Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminium wire (IEC 60317-0-3:2024)

This part of IEC 60317 specifies the general requirements of enamelled round aluminium
winding wires with or without a bonding layer.
The range of nominal conductor diameters is given in the relevant specification sheet.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-3: Allgemeine Anforderungen - Lackisolierte Runddrähte aus Aluminiumdraht (IEC 60317-0-3:2024)

Spécifications pour types particuliers de fils de bobinage - Partie 0-3: Exigences générales - Fil de section circulaire en aluminium émaillé (IEC 60317-0-3:2024)

IEC 60317-0-3:2024 est disponible sous forme de IEC 60317-0-3:2024 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

L'IEC 60317-0-3:2024 spécifie les exigences générales pour les fils de bobinage de section circulaire en aluminium émaillé, avec ou sans couche adhérente. La plage des diamètres nominaux des conducteurs est donnée dans la feuille de spécification appropriée.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) révision de l'Article 7, pour indiquer que l'essai ne s'applique pas;
b) révision de l'Article 10, pour indiquer que l'essai ne s'applique pas.

Specifikacije za posebne vrste navijalnih žic - 0-3. del: Splošne zahteve - Emajliran okrogel aluminijev vodnik (IEC 60317-0-3:2024)

General Information

Status
Published
Public Enquiry End Date
31-Oct-2023
Publication Date
27-Oct-2024
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
23-Oct-2024
Due Date
28-Dec-2024
Completion Date
28-Oct-2024

Relations

Buy Standard

Standard
EN IEC 60317-0-3:2024
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2024
Specifikacije za posebne vrste navijalnih žic - 0-3. del: Splošne zahteve - Emajliran
okrogel aluminijev vodnik (IEC 60317-0-3:2024)
Specifications for particular types of winding wires - Part 0-3: General requirements -
Enamelled round aluminium wire (IEC 60317-0-3:2024)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-3:
Allgemeine Anforderungen - Lackisolierte Runddrähte aus Aluminiumdraht (IEC 60317-0
-3:2024)
Spécifications pour types particuliers de fils de bobinage - Partie 0-3: Exigences
générales - Fil de section circulaire en aluminium émaillé (IEC 60317-0-3:2024)
Ta slovenski standard je istoveten z: EN IEC 60317-0-3:2024
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60317-0-3

NORME EUROPÉENNE
EUROPÄISCHE NORM October 2024
ICS 29.060.10 Supersedes EN 60317-0-3:2008;
EN 60317-0-3:2008/A1:2013;
EN 60317-0-3:2008/A2:2019
English Version
Specifications for particular types of winding wires - Part 0-3:
General requirements - Enamelled round aluminium wire
(IEC 60317-0-3:2024)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-3: Exigences générales - Fil de section circulaire Wickeldrähten - Teil 0-3: Allgemeine Anforderungen -
en aluminium émaillé Lackisolierte Runddrähte aus Aluminium
(IEC 60317-0-3:2024) (IEC 60317-0-3:2024)
This European Standard was approved by CENELEC on 2024-10-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-3:2024 E

European foreword
The text of document 55/2049/FDIS, future edition 4 of IEC 60317-0-3, prepared by TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-10-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-10-31
document have to be withdrawn
This document supersedes EN 60317-0-3:2008 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60317-0-3:2024 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60264 (series) NOTE Approved as EN 60264 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the EN IEC 60172 -
temperature index of enamelled and tape
wrapped winding wires
IEC 60317 series Specifications for particular types of EN 60317 series
winding wires
IEC 60851 series Winding wires - Test methods EN IEC 60851 series
ISO 3 - Preferred numbers - Series of preferred - -
numbers
ASTM B233-97 - Standard Specification for Aluminum 1350 - -
Drawing Stock for Electrical Purposes
Aluminium and aluminium alloys - Drawing EN 1715-2 -
stock - Part 2: Specific requirements for
electrical applications
IEC 60317-0-3 ®
Edition 4.0 2024-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 0-3: General requirements – Enamelled round aluminium wire

Spécifications pour types particuliers de fils de bobinage –

Partie 0-3: Exigences générales – Fil de section circulaire en aluminium émaillé

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10  ISBN 978-2-8322-9617-2

– 2 – IEC 60317-0-3:2024 © IEC 2024
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes, and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor diameter . 9
4.2 Out of roundness of conductor . 11
4.3 Minimum increase in diameter due to the insulation and the bonding layer . 11
4.3.1 Enamelled wires without a bonding layer . 11
4.3.2 Enamelled wires with a bonding layer . 11
4.4 Maximum overall diameter . 11
4.4.1 Enamelled wires without a bonding layer . 11
4.4.2 Enamelled wires with a bonding layer . 12
5 Electrical resistance . 12
6 Elongation . 12
7 Springiness . 12
8 Flexibility and adherence . 12
8.1 Mandrel winding test (nominal conductor diameters up to and including
1,600 mm) . 12
8.2 Stretching test (nominal conductor diameters over 1,600 mm) . 13
8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) . 13
8.4 Peel test (nominal conductor diameters over 1,000 mm) . 13
9 Heat shock . 13
9.1 Nominal conductor diameters up to and including 1,600 mm . 13
9.2 Nominal conductor diameters over 1,600 mm . 13
10 Cut-through . 13
11 Resistance to abrasion . 13
12 Resistance to solvents . 13
13 Breakdown voltage . 14
13.1 General . 14
13.2 Nominal conductor diameters up to and including 2,500 mm . 14
13.3 Nominal conductor diameters over 2,500 mm . 14
14 Continuity of insulation (nominal conductor diameters up to and including
1,600 mm) . 15
15 Temperature index . 15
16 Resistance to refrigerants . 15
17 Solderability . 15
18 Heat or solvent bonding . 15
19 Dielectric dissipation factor . 16

IEC 60317-0-3:2024 © IEC 2024 – 3 –
20 Resistance to transformer oil . 16
21 Loss of mass . 16
23 Pin hole test . 16
30 Packaging . 16
Annex A (informative) Dimensions for intermediate nominal conductor diameters
(R 40) . 17
A.1 General . 17
A.2 Enamelled wires without a bonding layer. 17
A.3 Enamelled wires with a bonding layer . 18
Annex B (normative) Method for the calculation of linear resistance . 19
Annex C (informative) Resistance . 20
Bibliography . 21

Table 1 – Dimensions of enamelled wires (R 20). 10
Table 2 – Dimensions of enamelled wires with a bonding layer (R 20) . 11
Table 3 – Elongation . 12
Table 4 – Mandrel winding . 12
Table 5 – Heat shock .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.