SIST EN ISO 19085-9:2020

Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2019)

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as “table saws” (in the USA), hereinafter referred to as “machines”, designed to cut wood and material with similar physical characteristics to wood, when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

Holzbearbeitungsmaschinen - Sicherheit - Teil 9: Tischkreissägemaschinen (mit und ohne Schiebetisch) (ISO 19085-9:2019)

Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen zur Verfügung für stationäre und verschiebbare Tischkreissägemaschinen (mit oder ohne Schiebetisch und/oder abnehmbarem Vorschubapparat), die (in den USA) auch als „table saws“ bekannt sind, nachfolgend als „Maschinen“ bezeichnet, die gestaltet sind zum Schneiden von Holz und Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz.
ANMERKUNG 1 Hinsichtlich der Definition von stationären und verschiebbaren Maschinen siehe ISO 19085-1:2017, 3.4 und 3.5.
Es behandelt alle in Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vom Hersteller vorgesehenen Bedingungen verwendet, eingestellt und gewartet werden, einschließlich des vernünftigerweise vorhersehbaren Fehlgebrauchs. Ferner werden die Phasen Transport, Montage, Demontage, Rückbau und Verschrottung berücksichtigt.
ANMERKUNG 2 Hinsichtlich zutreffender aber nicht signifikanter Gefährdungen, z. B. scharfe Kanten des Maschinengestells, siehe ISO 12100:2010.
Es gilt auch für Maschinen, die mit einer oder mehreren der folgenden Einrichtungen oder Arbeitsaggregate, deren Gefährdungen behandelt wurden, ausgestattet sind:
- Einrichtung zum Anheben und Absenken des Hauptsägeblatts und des Ritzsägeblatts durch den Tisch;
- Einrichtung zum Schrägstellen des Hauptsägeblatts und des Ritzsägeblatts für Winkelschnitte;
- Einrichtung zum Ritzsägen;
- Einrichtung zum Nuten mit Fräswerkzeug mit einer Breite von nicht mehr als 20 mm in einem Durchgang;
- abnehmbarer Vorschubapparat;
- zusätzlicher handbetätigter Schiebetisch;
- kraftbetätigte Werkstückspanneinrichtung.
ANMERKUNG 3 Tischkreissägemaschinen werden zum Besäumen, Querschneiden, für Formatschnitte und zum Nuten verwendet.
Dieses Dokument gilt nicht für:
a) transportable/verschiebbare Maschinen für die bestimmungsgemäße Verwendung im Freien auf Baustellen;
ANMERKUNG 4 Baustellenkreissägen unterliegen den Anforderungen in ISO 19085-10:2018.
b) handgeführte Holzbearbeitungsmaschinen einschließlich aller Anpassungen, die den Einsatz in einer anderen Betriebsart ermöglichen, z.B. Tischmontage;
c) Maschinen, die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind;
d) Maschinen, die vor dem Datum seiner Veröffentlichung als Internationale Norm hergestellt wurden;
e) transportable Maschinen mit einem größten Sägeblattdurchmesser ≤ 315 mm.
ANMERKUNG 5 Transportable motorbetriebene Elektrowerkzeuge werden in IEC 62841 1:2014 zusammen mit IEC 62841-3-1:2014 behandelt.

Machines à bois - Sécurité - Partie 9: Scies à table de menuisier (avec et sans table mobile) (ISO 19085-9:2019)

Le présent document donne les exigences et les mesures de sécurité pour les scies à table de menuisier, fixes ou transportables, avec ou sans table mobile et/ou unité d'avance mécanisée démontable,), également connues en tant que «scies à table» (aux États-Unis), ci-après désignées «machines», conçues pour la coupe de bois et de matériau présentant des caractéristiques physiques similaires à celles du bois.
NOTE 1    Pour la définition de machine fixe et transportable, voir l'ISO 19085‑1:2017, 3.4 et 3.5.
Il traite de tous les phénomènes dangereux, situations dangereuses et événements dangereux significatifs, tels qu'énumérés à l'Article 4, applicables à ces machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut sont également prises en compte.
NOTE 2    Pour les phénomènes dangereux pertinents mais non significatifs, par exemple, les arêtes vives du bâti de la machine, voir l'ISO 12100:2010.
Il est également applicable aux machines équipées d'un ou plusieurs des dispositifs, ou unité de travail, suivants, dont les phénomènes dangereux ont été traités:
—          dispositif pour relever et abaisser la lame de scie principale et la lame de scie d'incision par rapport à la table;
—          dispositif pour incliner la lame de scie principale et la lame de scie d'incision pour une coupe en angle;
—          dispositif pour l'incision;
—          dispositif de rainurage à l'aide d'un outil de fraisage ayant une largeur ne dépassant pas 20 mm en une seule passe;
—          unité d'avance mécanisée démontable;
—          table mobile supplémentaire à commande manuelle;
—          dispositif mécanisé de bridage de la pièce.
NOTE 3    Les scies à table de menuisier sont utilisées pour le délignage, le tronçonnage, la coupe au format et le rainurage.
Le présent document ne s'applique pas:
a)    aux machines transportables/déplaçables destinées à une utilisation en extérieur ou sur les chantiers de construction;
NOTE 4    Les scies de chantier sont couvertes par les exigences de l'ISO 19085‑10:2018.
b)    aux machines à bois portatives, y compris toute adaptation permettant leur utilisation de manière différente, c'est-à-dire fixées sur un bâti;
c)    aux machines prévues pour une utilisation en atmosphère explosible;
d)    aux machines fabriquées avant sa date de publication comme Norme internationale;
e)    aux machines transportables ayant un diamètre maximal de lame de scie ≤ 315 mm.
NOTE 5    Les machines-outils électriques transportables sont couvertes par les IEC 62841‑1:2014 et IEC 62841‑3‑1:2014.

Lesnoobdelovalni stroji - Varnost - 9. del: Krožne žage (s podajalno mizo ali brez nje) (ISO 19085-9:2019)

General Information

• Status: Withdrawn
• Public Enquiry End Date: 06-Jul-2016
• Publication Date: 10-Sep-2020
• Withdrawal Date: 05-Dec-2024
• ICS: 13.110 - Safety of machinery
• ICS: 25.080.60 - Sawing machines
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: VSN - Safety of machinery
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Dec-2024
• Due Date: 28-Dec-2024
• Completion Date: 06-Dec-2024
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN ISO 19085-9:2020 - Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2019)

Relations

• Replaces: SIST EN 1870-19:2014 - Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws
• Effective Date: 08-Jun-2022
• Replaces: SIST EN 1870-19:2014 - Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws
• Effective Date: 15-Apr-2020
• Revises: SIST EN ISO 19085-9:2025 - Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2024)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2020
Nadomešča:
SIST EN 1870-19:2014
Lesnoobdelovalni stroji - Varnost - 9. del: Krožne žage (s podajalno mizo ali brez
nje) (ISO 19085-9:2019)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding
table) (ISO 19085-9:2019)
Holzbearbeitungsmaschinen - Sicherheit - Teil 9: Tischkreissägemaschinen (mit und
ohne Schiebetisch) (ISO 19085-9:2019)
Machines à bois - Sécurité - Partie 9: Scies à table de menuisier (avec et sans table
mobile) (ISO 19085-9:2019)
Ta slovenski standard je istoveten z: EN ISO 19085-9:2020
ICS:
13.110 Varnost strojev Safety of machinery
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19085-9
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 79.120.10; 13.110 Supersedes EN 1870-19:2013
English Version
Woodworking machines - Safety - Part 9: Circular saw
benches (with and without sliding table) (ISO 19085-
9:2019)
Machines à bois - Sécurité - Partie 9: Scies circulaires à Holzbearbeitungsmaschinen - Sicherheit - Teil 9:
table de menuisier (avec et sans table mobile) (ISO Tischkreissägemaschinen (mit und ohne Schiebetisch)
19085-9:2019) (ISO 19085-9:2019)
This European Standard was approved by CEN on 21 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-9:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 19085-9:2020) has been prepared by Technical Committee ISO/TC 39 "Machine
tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines - Safety” the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1870-19:2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19085-9:2019 has been approved by CEN as EN ISO 19085-9:2020 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396” to
provide one voluntary means of conforming to essential requirements of the new approach Machinery
Directive 2006/42/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard Directive 2006/42/EC
Essential Requirements (ERs) of Directive Clauses / subclauses of this EN Remarks/Notes
2006/42/EC
1.1.2 Principles of safety integration

a) fitted for its function Clauses 5, 6, 7, 8
b) eliminate or reduce the risks, give measures, Clauses 5, 6, 7, 8

inform
c) intended use and reasonably foreseeable Clauses 5, 6, 7, 8

misuse
d) constraints in use 7.5, 8.3

e) equipment 6.1, 8.3
1.1.3 Materials and products 6.2, 7.3

1.1.4 Lighting 8.3
1.1.5 Design of machinery to facilitate its 8.3

handling
1.1.6 Ergonomics 7.5
1.1.7 Operating position 5.2
1.2.1 Safety and reliability of control systems 5.1, 5.7, 5.8, 5.11, 5.12, 5.13, 6.5, 6.6,

7.7
1.2.2 Control devices 5.2, 5.3, 5.4, 5.7

1.2.3 Starting 5.3
1.2.4 Stopping 5.4, 5.5, 6.4
1.2.4.1 Normal stop 5.4.2
1.2.4.3 Emergency stop 5.4.4
1.2.6 Failure of the power supply 5.8, 7.7

1.3.1 Risk of loss of stability 6.1, 8.3
1.3.2 Risk of break-up during operation 6.2, 8.3

1.3.3 Risks due to falling or ejected objects 6.2, 6.3, 6.5, 6.8, 6.9, 8.3

1.3.6 Risks relating to variations in the operating 5.7, 6.6

conditions
1.3.7 Risks related to moving parts 6.6, 6.7, 8.3

1.3.8 Choice of protection against risks related to 6.5, 6.6, 6.7, 8.3

moving parts
1.3.8.1 Moving transmission parts 6.6.3

1.3.8.2 Moving parts involved in the process 6.6.2

1.3.9 Risk of uncontrolled movements 6.1.1

1.4.1 General requirements 6.9

1.4.2.1 Fixed guards 6.5.1
1.4.2.2 Interlocking movable guards 6.5.2

1.4.2.3 Adjustable guards restricting access 6.6.2

1.4.3 Special requirements for protective devices 6.5.3

1.5.1 Electricity supply 7.4, 7.13

1.5.2 Static electricity 7.11
1.5.3 Energy supply other than electricity 7.7

1.5.4 Errors of fitting 7.12
1.5.6 Fire 7.1
1.5.8 Noise 7.2
1.5.11 External radiation 7.9
1.5.12 Laser equipment 7.10
1.5.13 Emission of hazardous materials and 7.3

substances
1.6.1 Machinery maintenance 7.14, 8.3

1.6.2 Access to operating position and servicing 7.14, 8.3

points
1.6.3 Isolation of energy sources 7.13, 8.3

1.6.4 Operator intervention 7.14, 8.3

1.6.5 Cleaning of internal parts 7.14, 8.3

1.7.1 Information and warnings on the 7.10, 8.1, 8.2

machinery
1.7.2 Warning devices 7.10, 8.1

1.7.3 Marking of machinery 8.2

1.7.4 Instructions 7.10, 8.3
2.3 Machinery for working wood and analogous

materials
a) guiding 6.10, 6.11
b) ejection 6.2, 6.3, 6.5, 6.6, 6.8, 6.9, 8.3

c) brake 5.5, 6.4
d) accidental tool contact 6.6.2, 8.3

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 19085-9
First edition
2019-04
Woodworking machines — Safety —
Part 9:
Circular saw benches (with and
without sliding table)
Machines à bois — Sécurité —
Partie 9: Scies circulaires à table de menuisier (avec et sans table
mobile)
Reference number
ISO 19085-9:2019(E)
©
ISO 2019
ISO 19085-9:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 19085-9:2019(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 List of significant hazards . 3
5 Safety requirements and measures for controls . 5
5.1 Safety and reliability of control systems . 5
5.2 Control devices . 5
5.3 Start . 6
5.4 Safe stops . 7
5.4.1 General. 7
5.4.2 Normal stop . 7
5.4.3 Operational stop . 7
5.4.4 Emergency stop . 7
5.5 Braking function of tool spindles . 7
5.6 Mode selection . 7
5.7 Spindle speed changing . 7
5.7.1 Spindle speed changing by changing belts on the pulleys . 7
5.7.2 Spindle speed changing by incremental speed change motor . 7
5.7.3 Infinitely variable speed by frequency inverter . 7
5.8 Failure of any power supply .
...