SIST EN 80:1998/A1:1998
(Amendment)Wall hung urinals without built-in trap - Connecting dimensions
- BACK
- 30-Nov-1998
- 30-Nov-2001
- 91.140.70
- 89/106/EEC
- IOVO
Wall hung urinals without built-in trap - Connecting dimensions
Wandurinale ohne eingebauten Geruchverschluß - Anschlußmaße
Urinoirs muraux sans siphon incorporé - Cotes de raccordement
Zidni pisoar brez vgrajene smradne zapore - Priključne mere
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 80:1998/A1:1998
01-december-1998
=LGQLSLVRDUEUH]YJUDMHQHVPUDGQH]DSRUH3ULNOMXþQHPHUH
Wall hung urinals without built-in trap - Connecting dimensions
Wandurinale ohne eingebauten Geruchverschluß - Anschlußmaße
Urinoirs muraux sans siphon incorporé - Cotes de raccordement
Ta slovenski standard je istoveten z: EN 80:1978/A1:1978
ICS:
91.140.70 Sanitarne n
...
This May Also Interest You
This document specifies:
- the dimensional, mechanical, hydraulic and acoustic characteristics with which sanitary tapware aerators (with and without flow regulation) should comply;
- the procedures for testing these characteristics.
This document is applicable to:
- Sanitary tapware aerators intended to be mounted on tapware used with sanitary appliances in toilets, bathrooms and kitchens (e.g. single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
—-Sanitary tapware aerators used under the following pressure and temperature conditions:
Note 1: Sanitary tapware aerators can only be connected downstream of the obturator of the sanitary tapware product.
Note 2: For the purposes of brevity, sanitary tapware aerators will be detailed only as aerators in the rest of this document.
Note 3: The tests described in this document are type tests (laboratory tests) and not quality control tests carried out during manufacture.
- Standard19 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft19 pagesEnglish languagesale 10% offe-Library read for×1 day
This document describes the installation rules that must be followed to ensure proper functioning of the drainage system depending on the specified performance of the sanitary appliances.
These performance characteristics of sanitary appliances (defined in the harmonized standards EN 997, EN 13407, EN 14688, EN 14528 and EN 14527) are explained and brought into line with the application rules of standard series EN 12056.
According to Regulation (EU) 305/2011, legally binding information on building requirements must be provided by the National Product Information Point. Therefore, additional national requirements are mentioned informatively where information is available.
- Technical report27 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft27 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the connecting dimensions of WC pans and WC suites regardless of the materials used for their manufacture.
This document does not apply to siphonic action WC pans and WC suites.
NOTE 1 Other connecting dimensions are permitted, e. g. special designs of WC pans, if the manufacturer supplies or recommends the appropriate fittings.
NOTE 2 The shape of the appliance in the figures is for illustration only; it in no way prejudices the final shape of the appliance, which is left to the initiative of the manufacturer.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies "characteristics", test methods and procedures for evaluation of conformity for baths used for domestic purposes and personal hygiene, which ensure that the product, when installed and maintained in accordance with the manufacturer's instructions, will satisfy requirements for cleanability and durability.
This European Standard is applicable to all sizes and shapes of baths.
This European Standard does not cover baths for use with medical provisions.
NOTE 1 For the purpose of this standard the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings.
NOTE 2 Annex A lists characteristics of materials commonly used for manufacturing baths.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies "characteristics", test methods and procedures for evaluation of conformity for shower trays used for domestic purposes which ensure that the product, when installed, used and maintained in accordance with the manufacturer's instructions, will satisfy cleanability and durability when used for personal hygiene.
This standard is applicable to all sizes and shapes of shower trays.
This standard does not cover shower trays for use with medical provisions.
NOTE 1 For the purpose of this standard the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings.
NOTE 2 Annex A lists characteristics of materials commonly used for manufacturing shower trays.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies "characteristics" for whirlpool baths, having a rated voltage of not more than 250 V for single phase appliances and 480 V for other appliances, which are intended to be installed in indoor domestic situations and used in accordance with the manufacturer’s instructions for personal hygiene. Such whirlpool baths are tested and supplied as a complete independent unit designed to be drained down after every use. They may be transported in several separate parts, for assembly on site, to facilitate delivery.
Safety aspects of Whirlpool baths (except use by young children and slow moving/weak elderly or disabled individuals) are covered by EN 60335 2 60.
Exclusions: this standard does not cover additional requirements for whirlpool baths intended for uses where specific medical provisions are required, or whirlpool baths for communal uses where they are not drained down after every use. Portable whirlpool devices are not covered by this standard.
For the purposes of this standard the term ‘domestic situations’ includes use in hotels, accommodation for students, hospitals and similar buildings.
Warning: Slow moving elderly or disabled persons should take care when using whirlpool baths. Young children should not be allowed to use whirlpool baths without supervision.
NOTE 1 It is unrealistic to expect manufacturers to provide a definition of what constitutes a ‘slow moving elderly or disabled person’, or ‘young children’. The former is the responsibility of the individual or a carer. The latter is a parental responsibility.
NOTE 2 When EN 60335-2-60 is amended to cover use of whirlpool baths by slow moving elderly or disabled persons and young children the warning given above will be deleted from this standard.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies "characteristics" for shower enclosures for domestic purposes which ensure that the product, when installed in accordance with the manufacturer's installation instructions, gives satisfactory performance when used as intended.
This European Standard does not apply to shower cabinets or curtains and does not specify aesthetic and dimensional "characteristics".
NOTE For the purposes of this document the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required.
- Standard37 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies design, performance requirements and the test methods for WC and urinal flushing cisterns with flushing mechanism, inlet valve and overflow.
This document covers flushing cisterns designed to be connected to drinking water installations inside buildings.
This standard does not cover automatic valveless siphon flushing cisterns for flushing urinals.
NOTE Flushing cisterns for one-piece WCs and close-coupled suites are covered by EN 997.
- Standard48 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies constructional and performance requirements together with test methods for close-coupled suites, one-piece and independent WC pans with integral trap used for personal hygiene manufactured from glazed ceramics or stainless steel.
This European Standard does not apply to squatting toilets, WC pans without integral trap or flushing cisterns as separate appliances.
In the case of independent WC pans, the associated flushing cisterns and pressure valves are covered by other standards and the reference to cisterns in this standard is related only to the definition and requirements of flushing volume.
In the case of close-coupled suites and one-piece WCs, this standard also specifies design, performance requirements and the test methods for designated flushing cisterns with flushing mechanisms, inlet valves and overflows. For these products, this standard covers flushing cisterns designed to be connected to drinking water installations inside buildings.
Before installation of WCs, EN 12056 2 and national requirements need to be taken into consideration.
- Standard64 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the functional characteristics and test methods for wash basins for domestic purposes.
NOTE 1 For the purposes of this standard the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required.
NOTE 2 All drawings are examples only. The shape of the appliance is left to the discretion of the manufacturer.
- Standard24 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.