Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO 15877-2:2009)

This part of ISO 15877 specifies the general requirements of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1).

Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-C) - Teil 2: Rohre

Dieser Teil von ISO/DIS 15877 legt Anforderungen an Rohre aus chloriertem Polyvinylchlorid (PVC-C) für Rohrleitungssysteme fest, die in der Warm- und Kaltwasserinstallation innerhalb von Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) und in Heizungsanlagen unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen (siehe Tabelle 1 von ISO/DIS 15877-1) eingesetzt werden.
Diese Norm enthält Festlegungen zu Anwendungsklassen, die sich auf Betriebsbedingungen beziehen, sowie Festlegungen über zulässige Betriebsdrücke und Rohrserien. Diese Norm gilt nicht, wenn für TD, Tmax und Tmal höhere als die in Tabelle 1 von ISO/DIS 15877-1 aufgeführten Werte zugrunde gelegt werden.
ANMERKUNG   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
Sie legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird.
Zusammen mit den übrigen Teilen der ISO/DIS 15877 (siehe Vorwort) gilt dieser Teil für Rohre aus PVC-C, deren Verbindungen untereinander sowie mit anderen Rohrleitungsteilen aus PVC-C, anderen Kunststoffen oder metallenen Werkstoffen, die für die Warm- und Kaltwasserinstallation vorgesehen sind.

Systemes de canalisations en plastique pour les installations d'eau chaude et froide - Poly(chlorure de vinyle) chloré (PVC-C) - Partie 2: Tubes (ISO 15877-2:2009)

L'ISO 15877-2:2009 spécifie les exigences des tubes en poly(chlorure de vinyle) chloré (PVC-C) pour les systèmes de canalisations destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments pour le transport de l'eau, destinée ou non à la consommation humaine (systèmes domestiques) et aux systèmes de chauffage, à des pressions et des températures de service correspondant à la classe d'application.
L'ISO 15877-2:2009 couvre une gamme de conditions de service (classes d'application), de pressions de service et de séries de tubes. L'ISO 15877-2:2009 spécifie également les paramètres d'essai pour les méthodes d'essai auxquelles elle fait référence.
Conjointement avec les autres parties de l'ISO 15877, elle s'applique aux tubes en PVC-C, aux raccords, à leurs assemblages et aux assemblages avec des composants faits en d'autres matériaux, plastiques ou non plastiques, pouvant être utilisés avec des installations d'eau chaude et froide.

Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Klorirani polivinilklorid (PVC-C) - 2. del: Cevi (ISO 15877-2:2009)

General Information

Status
Published
Publication Date
11-May-2009
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Apr-2009
Due Date
26-Jun-2009
Completion Date
12-May-2009

Relations

Buy Standard

Standard
EN ISO 15877-2:2009
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15877-2:2009
01-junij-2009
1DGRPHãþD
SIST EN ISO 15877-2:2004
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
.ORULUDQLSROLYLQLONORULG 39&& GHO&HYL ,62
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl
chloride) (PVC-C) - Part 2: Pipes (ISO 15877-2:2009)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes
Polyvinylchlorid (PVC-C) - Teil 2: Rohre
Systemes de canalisations en plastique pour les installations d'eau chaude et froide -
Poly(chlorure de vinyle) chloré (PVC-C) - Partie 2: Tubes (ISO 15877-2:2009)
Ta slovenski standard je istoveten z: EN ISO 15877-2:2009
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 15877-2:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15877-2:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 15877-2:2009
EUROPEAN STANDARD
EN ISO 15877-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2009
ICS 23.040.20; 91.140.60 Supersedes EN ISO 15877-2:2003
English Version
Plastics piping systems for hot and cold water installations -
Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO
15877-2:2009)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Poly(chlorure de Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-
vinyle) chloré (PVC-C) - Partie 2: Tubes (ISO 15877- C) - Teil 2: Rohre (ISO 15877-2:2009)
2:2009)
This European Standard was approved by CEN on 28 February 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15877-2:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15877-2:2009
EN ISO 15877-2:2009 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15877-2:2009
EN ISO 15877-2:2009 (E)
Foreword
This document (EN ISO 15877-2:2009) has been prepared by Technical Committee CEN/TC 155 "Plastics
piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2009, and conflicting national standards shall be
withdrawn at the latest by September 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15877-2:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 15877-2:2009

---------------------- Page: 6 ----------------------

SIST EN ISO 15877-2:2009

INTERNATIONAL ISO
STANDARD 15877-2
Second edition
2009-03-15


Plastics piping systems for hot and cold
water installations — Chlorinated
poly(vinyl chloride) (PVC-C) —
Part 2:
Pipes
Systèmes de canalisations en plastique pour les installations d’eau
chaude et froide — Poly(chlorure de vinyle) chloré (PVC-C) —
Partie 2: Tubes





Reference number
ISO 15877-2:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 15877-2:2009
ISO 15877-2:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15877-2:2009
ISO 15877-2:2009(E)
Contents Page
Foreword. iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols. 2
4 Material . 2
4.1 General. 2
4.2 Pipe material. 2
4.3 Evaluation of σ -values. 2
LPL
4.4 Influence on water intended for human consumption. 6
5 General characteristics . 6
5.1 Appearance . 6
5.2 Chamfering . 6
5.3 Opacity. 6
6 Geometrical characteristics. 6
6.1 General. 6
6.2 Dimensions of pipes. 7
6.3 Wall thicknesses and their tolerances. 7
7 Mechanical characteristics . 8
7.1 Resistance to internal pressure . 8
7.2 Impact resistance. 9
7.3 Tensile strength . 10
8 Physical characteristics. 10
9 Performance requirements . 11
10 Adhesives . 11
11 Marking . 12
11.1 General. 12
11.2 Minimum required marking. 12
11.3 Additional marking . 12
Annex A (informative) Derivation of the maximum calculated pipe value, S . 13
calc,max
Bibliography . 15

© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 15877-2:2009
ISO 15877-2:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15877-2 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes
and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This part of ISO 15877 is a part of a System Standard for plastics piping systems of a particular material for a
specified application. There are a number of such System Standards.
The System Standards are consistent with general standards on functional requirements and recommended
practices for installation.
This second edition cancels and replaces the first edition (ISO 15877-2:2003).
1)
ISO 15877 consists of the following parts , under the general title Plastics piping systems for hot and cold
water installations — Chlorinated poly(vinyl chloride) (PVC-C):
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fittings
⎯ Part 5: Fitness for purpose of the system
⎯ Part 7: Guidance for the assessment of conformity [Technical Specification].

1) This System Standard does not incorporate a Part 4: Ancillary equipment or a Part 6: Guidance for installation. For
ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made from different
[5]
materials, intended to be used for hot and cold water installations, is covered by ENV 12108 .
iv © ISO 2009 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 15877-2:2009
ISO 15877-2:2009(E)
At the date of publication of this part of ISO 15877, System Standards Series for piping systems of other
plastics materials used for hot and cold water installations are the following:
ISO 15874 (all parts), Plastics piping systems for hot and cold water installations ― Polypropylene (PP)
ISO 15875 (all parts), Plastics piping systems for hot and cold water installations ― Crosslinked polyethylene
(PE-X)
ISO 15876 (all parts), Plastics piping systems for hot and cold water installations ― Polybutylene (PB)
2)
ISO 22391:— (all parts), Plastics piping systems for hot and cold water installations ― Polyethylene of
raised temperature resistance (PE-RT)

2) To be published. (Revisions of ISO 22391-1:2007, ISO 22391-2:2007, ISO 22391-3:2007, ISO 22391-5:2007.)
© ISO 2009 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 15877-2:2009
ISO 15877-2:2009(E)
Introduction
The System Standard, of which this is Part 2, specifies the requirements for a piping system when made from
chlorinated poly(vinyl chloride) (PVC-C). The piping system is intended to be used for hot and cold water
installations and for heating system installations.
In respect of potential adverse effects on the quality of water intended for human consumption caused by the
product covered by this part of ISO 15877, the following are relevant.
a) This part of ISO 15877 provides no information as to whether the product may be used without restriction
in any of the Member States of the EU or EFTA.
b) It should be noted that, while awaiting the adoption of verifiable European criteria, existing national
regulations concerning the use and/or the characteristics of this product remain in force.
When using solvent cement, relevant national safety rules or regulations concerning their use (e.g. protection
of workers) are to be observed.
Requirements and test methods for material and components other than pipes are specified in ISO 15877-1
and ISO 15877-3. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 15877-5.
ISO/TS 15877-7 gives guidance for the assessment of conformity.
This part of ISO 15877 specifies the characteristics of pipes.
vi © ISO 2009 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 15877-2:2009
INTERNATIONAL STANDARD ISO 15877-2:2009(E)

Plastics piping systems for hot and cold water installations —
Chlorinated poly(vinyl chloride) (PVC-C) —
Part 2:
Pipes
1 Scope
This part of ISO 15877 specifies the requirements of pipes made from chlorinated poly(vinyl chloride) (PVC-C)
for piping systems intended to be used for hot and cold water installations within buildings for the conveyance
of water, whether or not intended for human consumption (domestic systems) and for heating systems, under
design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 15877-1:2009).
This part of ISO 15877 covers a range of service conditions (application classes), design pressures and pipe
series. For values of T , T and T in excess of those in Table 1 of ISO 15877-1:2009, this part of
D max mal
ISO 15877 does not apply.
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the test parameters for the test methods referred to in this part of ISO 15877.
In conjunction with the other parts of ISO 15877, it is applicable to PVC-C pipes, their joints and joints with
components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water
installations.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids ― Determination of
the resistance to internal pressure ― Part 1: General method
ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids ― Determination of
the resistance to internal pressure ― Part 2: Preparation of pipe test pieces
ISO 2505, Thermoplastics pipes ― Longitudinal reversion ― Test methods and parameters
ISO 3126, Plastics piping systems ― Plastics components ― Determination of dimensions
ISO 6259-1, Thermoplastics pipes ― Determination of tensile properties ― Part 1: General test method
ISO 6259-2, Thermoplastics pipes ― Determination of tensile properties ― Part 2: Pipes made of
unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) and high-impact
poly(vinyl chloride) (PVC-HI)
ISO 7686, Plastics pipes and fittings ― Determination of opacity
© ISO 2009 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 15877-2:2009
ISO 15877-2:2009(E)
ISO 9080, Plastics piping and ducting systems ― Determination of the long-term hydrostatic strength of
thermoplastics materials in pipe form by extrapolation
ISO 15877-1:2009, Plastics piping systems for hot and cold water installations ― Chlorinated
poly(vinyl chloride) (PVC-C) ― Part 1: General
ISO 15877-3:2009, Plastics piping systems for hot and cold water installations ― Chlorinated
poly(vinyl chloride) (PVC-C) ― Part 3: Fittings
ISO 15877-5:2009, Plastics piping systems for hot and cold water installations ― Chlorinated
poly(vinyl chloride) (PVC-C) ― Part 5: Fitness for purpose of the system
EN 727, Plastics piping and ducting systems ― Thermoplastics pipes and fittings ― Determination of Vicat
softening temperature (VS
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.