SIST EN 13601:2021
(Main)Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross sections and size ranges are:
- round, square and hexagonal rod with diameters or widths across flats from 2 mm up to and including 160 mm;
- bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and including 250 mm;
- round, square, hexagonal and rectangular wire with diameters or widths across flats from 2 mm up to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.
NOTE Drawn, round copper wire - plain or tinned, single or multiline - for the manufacture of electrical conductors is specified in EN 13602.
Kupfer und Kupferlegierungen - Stangen und Drähte aus Kupfer für die allgemeine Anwendung in der Elektrotechnik
Dieses Dokument legt die Zusammensetzung, die Anforderungen an die Eigenschaften einschließlich elektrischer Eigenschaften, Grenzabmaße und Grenzabweichungen für die Form für Stangen und Drähte aus Kupfer für die allgemeine Anwendung in der Elektrotechnik fest. Die Querschnitte und Maßbereiche sind:
— runde, quadratische und sechseckige Stangen mit Durchmessern oder Schlüsselweiten von 2 mm bis 160 mm;
— Rechteckstangen mit Dicken von 2 mm bis 40 mm und Breiten von 3 mm bis 250 mm;
— runde, quadratische, sechseckige und rechteckige Drähte mit Durchmessern oder Schlüsselweiten von 2 mm bis 25 mm und für Dicken von 0,5 mm bis 12 mm bei Breiten von 1 mm bis 250 mm.
Der Ablauf der Probenentnahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen des Dokuments sind ebenfalls festgelegt.
ANMERKUNG Gezogener Runddraht aus Kupfer, blank oder verzinnt, einzeln oder mehrfach, für die Herstellung von elektrischen Leitern ist in EN 13602 festgelegt.
Cuivre et alliages de cuivre - Barres et fils en cuivre pour usages électriques généraux
Le présent document spécifie la composition, les exigences de propriétés, y compris les propriétés électriques, ainsi que les tolérances sur les dimensions et la forme des barres et fils en cuivre pour usages
électriques généraux. Les sections et les dimensions sont les suivantes :
— des barres rondes, carrées et hexagonales avec des diamètres ou des largeurs sur plats compris
entre 2 mm et 160 mm inclus ;
— des barres rectangulaires avec des épaisseurs comprises entre 2 mm et 40 mm inclus et des largeurs
comprises entre 3 mm et 250 mm inclus ;
— des fils ronds, carrés, hexagonaux et rectangulaires avec des diamètres ou des largeurs sur plats
compris entre 2 mm et 25 mm inclus, ainsi que des épaisseurs comprises entre 0,5 mm et 12 mm
inclus avec des largeurs comprises entre 1 mm et 250 mm inclus.
Les modes opératoires d’échantillonnage et les méthodes d’essai pour la vérification de la conformité aux exigences du présent document sont également spécifiés.
NOTE Les fils ronds en cuivre étirés, nus ou étamés, monofilaires ou multifilaires, pour la fabrication des conducteurs électriques sont spécifiés dans l’EN 13602.
Baker in bakrove zlitine - Drogovi, palice in žice za splošno uporabo v elektrotehniki
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13601:2021
01-september-2021
Nadomešča:
SIST EN 13601:2013
Baker in bakrove zlitine - Drogovi, palice in žice za splošno uporabo v
elektrotehniki
Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
Kupfer und Kupferlegierungen - Stangen und Drähte aus Kupfer für die allgemeine
Anwendung in der Elektrotechnik
Cuivre et alliages de cuivre - Barres et fils en cuivre pour usages électriques généraux
Ta slovenski standard je istoveten z: EN 13601:2021
ICS:
77.150.30 Bakreni izdelki Copper products
SIST EN 13601:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13601:2021
---------------------- Page: 2 ----------------------
SIST EN 13601:2021
EN 13601
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2021
EUROPÄISCHE NORM
ICS 77.150.30 Supersedes EN 13601:2013
English Version
Copper and copper alloys - Copper rod, bar and wire for
general electrical purposes
Cuivre et alliages de cuivre - Barres et fils en cuivre Kupfer und Kupferlegierungen - Stangen und Drähte
pour usages électriques généraux aus Kupfer für die allgemeine Anwendung in der
Elektrotechnik
This European Standard was approved by CEN on 12 April 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13601:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designations . 7
4.1 Material . 7
4.1.1 General. 7
4.1.2 Symbol . 7
4.1.3 Number . 7
4.2 Material condition . 8
4.3 Product . 8
5 Ordering information . 9
6 Requirements . 11
6.1 Composition . 11
6.2 Mechanical properties . 11
6.3 Bending characteristics . 11
6.4 Electrical properties . 11
6.5 Freedom from hydrogen embrittlement . 11
6.6 Dimensions and tolerances . 11
6.6.1 Diameter or width across-flats . 11
6.6.2 Corner configuration . 11
6.6.3 Length. 13
6.7 Form tolerances . 13
6.7.1 General. 13
6.7.2 Twist . 13
6.7.3 Straightness . 14
6.7.4 Flatness of bar . 15
6.8 Wire in coils . 15
6.9 Mass tolerances . 15
6.10 Surface condition . 15
7 Sampling . 15
7.1 General. 15
7.2 Analysis . 15
7.3 Mechanical and electrical tests . 16
8 Test methods . 16
8.1 Analysis . 16
8.2 Tensile test . 16
8.3 Hardness test . 16
8.4 Bend test . 16
8.5 Electrical resistivity test . 17
8.6 Hydrogen embrittlement test . 17
8.7 Retests . 17
2
---------------------- Page: 4 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
8.8 Rounding of results . 17
9 Declaration of conformity and inspection documentation . 18
9.1 Declaration of conformity . 18
9.2 Inspection documentation . 18
10 Marking, packaging, labelling . 18
Annex A (informative) Characteristics of coppers for electrical purposes . 27
A.1 General grouping of copper types . 27
A.2 General characteristics . 27
A.3 Particular characteristics . 27
Bibliography . 29
3
---------------------- Page: 5 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
European foreword
This document (EN 13601:2021) has been prepared by Technical Committee CEN/TC 133 “Copper and
copper alloys”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2021, and conflicting national standards
shall be withdrawn at the latest by November 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13601:2013.
In comparison with the previous edition, the following technical modifications have been made:
— maximum diameters or widths across flats for bar, square, hexagonal and rectangular have been
expanded;
— the Scope has been modified;
— in Clause 6.5, Freedom from hydrogen embrittlement, the alloys Cu-OFE (CW009A) and Cu-PHCE
(CW022A) have been added;
— Table 3 has been modified to correct incongruent values;
— tolerances on width and thickness of bar and rectangular wire and maximum twist of square or
hexagonal rod or rectangular bar have been modified (see Table 6 and Table 10).
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
Introduction
The products specified in this document are those which are especially suitable for electrical purposes,
i.e. with specified electrical properties. Copper rod, bar and wire for general purposes are specified in
EN 12163, EN 12166 and EN 12167.
Annex A (informative) gives guidance on the characteristics of coppers for electrical purposes.
This is one document of a series of European Standards for copper products for electrical purposes.
Other copper products are specified as follows:
— EN 13599, Copper and copper alloys — Copper plate, sheet and strip for electrical purposes
— EN 13600, Copper and copper alloys — Seamless copper tubes for electrical purposes
— EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical
conductors
— EN 13604, Copper and copper alloys — Semiconductor devices, electronic and vacuum products made
from high conductivity copper
— EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes
5
---------------------- Page: 7 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
1 Scope
This document specifies the composition, property requirements including electrical properties, and
tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross-
sections and size ranges are:
— round, square and hexagonal rod with diameters or widths across-flats from 2 mm up to and
including 160 mm;
— bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and
including 250 mm;
— round, square, hexagonal and rectangular wire with diameters or widths across-flats from 2 mm up
to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths
from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this
document are also specified.
NOTE Drawn, round copper wire, plain or tinned, single or multiline, for the manufacture of electrical
conductors is specified in EN 13602.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1976, Copper and copper alloys - Cast unwrought copper products
EN ISO 2626, Copper - Hydrogen embrittlement test (ISO 2626)
EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1)
EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1)
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature
(ISO 6892-1)
EN ISO 7438, Metallic materials - Bend test (ISO 7438)
IEC 60468, Method of measurement of resistivity of metallic materials
6
---------------------- Page: 8 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
bar
straight product of uniform rectangular cross-section along its whole length
[SOURCE: EN 12167:2016, 3.2]
3.2
rod
straight product of uniform cross-section along its whole length
[SOURCE: EN 12163:2016, 3.1]
3.3
wire
wound product of uniform cross-section along its whole length
Note 1 to entry: Rectangles may have round or sharp corners.
[SOURCE: EN 12166:2016, 3.1]
3.4
deviation from circular form
difference between the maximum and the minimum diameters measured at any one cross-section of a
round product
[SOURCE: EN 12163:2016, 3.2]
4 Designations
4.1 Material
4.1.1 General
The material is designated either by symbol or by number (see Table 1 and Table 2).
4.1.2 Symbol
The material symbol designation is based on the designation system given in ISO 1190-1.
NOTE Although material symbol designations used in this document might be the same as those in other
standards using the designation system given in ISO 1190-1, the detailed composition requirements are not
necessarily the same.
4.1.3 Number
The material number designation is in accordance with the system given in EN 1412.
7
---------------------- Page: 9 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
4.2 Material condition
For the purposes of this document, the following designations, which are in accordance with the system
given in EN 1173, apply for the material condition:
D Material condition for the product as cold worked without specified mechanical properties;
H. Material condition designated by the minimum value of hardness requirement for the
product with mandatory hardness requirements;
R. Material condition designated by the minimum value of tensile strength requirement for the
product with mandatory tensile strength, 0,2 % proof strength and elongation
requirements.
Products in the H. condition may be specified to Vickers or Brinell hardness. The material condition
designation H. is the same for both hardness test methods.
Exact conversion between the material conditions designated H. and R. is not possible.
Material condition is designated by only one of the above designations.
4.3 Product
The product designation provides a standardized pattern of designation from which a rapid and
unequivocal description of a product can be conveyed in communication. It provides mutual
comprehension at the international level with regard to products which meet the requirements of the
relevant European Standard.
The product designation is no substitute for the full content of the standard.
The product designation for products to this document shall consist of:
a) denomination (rod, bar or wire);
b) number of this document (EN 13601);
c) material designation, either symbol or number (see Table 1 and Table 2);
d) material condition designation (see Table 3);
e) cross-sectional shape (the following designations shall be used as appropriate: RND for round, SQR
for square, HEX for hexagonal);
f) nominal cross-sectional dimensions:
1) round rod or wire: diameter;
2) square or hexagonal rod or wire: width across-flats;
3) bar or rectangular wire: thickness × width;
g) tolerance class for round, square or hexagonal rod or wire (see Table 5);
h) corner type for square or hexagonal rod, bar or rectangular wire (the following designations shall
be used as appropriate: SH for sharp, RD for rounded, CE for semi-circular edges) (see 6.6.2).
The derivation of a product designation is shown in Example 1 and other typical product designations
are shown in Example 2 and Example 3.
8
---------------------- Page: 10 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
EXAMPLE 1 Rod for electrical purposes conforming to this document, in material designated either Cu-ETP or
CW004A, in material condition H085, round, with nominal diameter 15 mm and tolerance Class A, will be
designated as follows:
Rod—EN 13601—Cu-ETP—H085—RND15A
or
EXAMPLE 2 Bar for electrical purposes conforming to this document, in material designated either CuAg0,10
or CW013A, in material condition R280, rectangular, nominal thickness 15 mm, nominal width 100 mm, semi-
circular edge, will be designated as follows:
Bar EN 13601—CuAg0,10—R280—15 × 100—CE
or
Bar EN 13601—CW013A—R280—15 × 100—CE
EXAMPLE 3 Wire for electrical purposes conforming to this document, in material designated either Cu-OF or
CW008A, in material condition H035, hexagonal, with nominal width across-flats 8 mm, tolerance Class B and
sharp corners, will be designated as follows:
Wire EN 13601—Cu-OF—H035—HEX8B—SH
or
Wire EN 13601—CW008A—H035—HEX8B—SH
5 Ordering information
In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser
and the supplier, the purchaser shall state on his enquiry and order the following information:
a) quantity of product required (mass, number of rods or bars or coils of wire);
b) denomination (rod, bar or wire);
c) number of this document (EN 13601);
d) material designation (see Table 1 and Table 2);
e) material condition designation (see 4.2 and Table 3);
f) cross-sectional shape (round, square, hexagonal or rectangular);
g) nominal dimensions (diameter, width across-flats or thickness × width);
9
---------------------- Page: 11 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
h) tolerance class for round, square or hexagonal rod or wire: either Class A (minus tolerance only) or
Class B (plus/minus tolerance) (see Table 5);
i) type of corner (see 6.6.2);
j) for rod or bar, the length required (see 6.6.3);
k) for wire, the coil type: pancake, traverse wound, bunch or on drums (see 6.8);
l) coil size requirements: inside and/or outside diameter and width or mass.
It is recommended that the product designation, as described in 4.3, is used for b) to i).
In addition, the purchaser shall also state on the enquiry and order any of the following, if required:
m) test method to be used for measurement of hardness, i.e. Brinell or Vickers (see 8.3) unless the test
method is to be left to the discretion of the supplier;
n) whether sawn or sheared ends are required (see 6.6.3);
o) whether special surface conditions are required (see 6.10);
p) whether a bend test is required (see 6.3);
q) whether form tolerances for wire are required (see 6.7.1);
r) whether length of wire is required (see 6.6.3);
s) whether sampling is required (see Clause 7);
t) whether a declaration of conformity is required (see 9.1);
u) whether an inspection document is required, and if so, which type (see 9.2);
v) whether there are any special requirements for marking, packaging or labelling (see Clause 10).
EXAMPLE 1 Ordering details for 250 pieces bar for general electrical purposes conforming to EN 13601, in
material designated either CuAg0,10 or CW013A, in material condition R280, rectangular, nominal thickness
15 mm, nominal width 100 mm, semi-circular edge, fixed length 4 500 mm:
250 pieces Bar EN 13601—CuAg0,10—R280—15 × 100—CE—4500 FL
or
250 pieces Bar EN 13601—CW013A—R280—15 × 100—CE—4500 FL
EXAMPLE 2 Ordering details for 1 000 kg wire for general electrical purposes conforming to EN 13601, in
material designated either Cu-OF or CW008A, in material condition H035, hexagonal, nominal width across flats
8 mm, tolerance Class B, with sharp corners, nominal inside diameter of coil 500 mm:
1 000 kg Wire EN 13601—Cu-OF—H035—HEX8B—SH—nominal inside diameter of coil 500 mm
or
1 000 kg Wire EN 13601—CW008A—H035—HEX8B—SH—nominal inside diameter of coil
500 mm
10
---------------------- Page: 12 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
6 Requirements
6.1 Composition
The composition shall conform to the requirements for the appropriate material given in Table 1 and
Table 2.
NOTE For characteristics of coppers for electrical purposes, see Annex A (informative).
6.2 Mechanical properties
The mechanical properties shall conform to the appropriate requirements given in Table 3. The tests
shall be carried out in accordance with either 8.2 (tensile test) or 8.3 (hardness test).
6.3 Bending characteristics
If required, bending characteristics shall be agreed between the purchaser and the supplier at the time
of enquiry and order. The test shall be carried out in accordance with 8.4.
6.4 Electrical properties
The electrical properties shall conform to the appropriate requirements given in Table 4. The test shall
be carried out in accordance with 8.5.
6.5 Freedom from hydrogen embrittlement
Rod, bar and wire in copper grades Cu-OF (CW008A), Cu-OFE (CW009A), CuAg0,04P (CW014A),
CuAg0,07P (CW015A), CuAg0,10P (CW016A), CuAg0,04(OF) (CW017A), CuAg0,07(OF) (CW018A),
CuAg0,10(OF) (CW019A), Cu-PHC (CW020A), Cu-HCP (CW021A) and Cu-PHCE (CW022A) shall show
no evidence of cracking, when tested and visually examined in accordance with 8.6.
6.6 Dimensions and tolerances
6.6.1 Diameter or width across-flats
The diameter or width across-flats of round, square, hexagonal or rectangular rod, bar or wire shall
conform to the appropriate tolerances given in Table 5 and Table 6.
6.6.2 Corner configuration
6.6.2.1 General
Rod, bar and wire may be supplied with sharp corners, rounded corners or semi-circular edges. The
type of corner shall be specified at the time of order [see Clause 5 list entry i)].
11
---------------------- Page: 13 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
6.6.2.2 Sharp corners
Sharp corners (SH) of square, hexagonal and rectangular rod, bar and wire (see Figure 1) shall conform
to Table 7.
Figure 1 — Sharp corner
6.6.2.3 Rounded corners
Rounded corners (RD) of square, hexagonal and rectangular rod, bar and wire (see Figure 2) shall
conform to Table 8.
Figure 2 — Rounded corner
6.6.2.4 Semi-circular edge
The radius of semi-circular edges (CE) of rectangular bar and wire (see Figure 3) is half the thickness
and shall conform to a tolerance of ± 20 % of the radius; the arc of curvature shall merge smoothly into
the adjacent flat side and shall be free from sharp, rough or projecting corners.
Figure 3 — Semi-circular edge
12
---------------------- Page: 14 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
6.6.3 Length
6.6.3.1 General
Rod and bar shall be supplied either in manufactured length (ML) or fixed length (FL), with ends either
sawn or sheared.
If required, the length of wire shall be agreed between the purchaser and the supplier.
6.6.3.2 Manufactured lengths (ML)
Manufactured lengths (ML) shall be supplied in the nominal lengths. The tolerances are by agreement
between the purchaser and the supplier.
It is permissible for 10 % of the number of rods and bars in a consignment to be shorter, but not less
than 50 % of the nominal length.
6.6.3.3 Fixed lengths (FL)
The lengths supplied as fixed lengths shall conform to the tolerances given in Table 9.
The deviation from squareness of the cut shall be a maximum of 2 % of the diameter or width or major
across-flats dimension of the rod and bar and is included in the fixed length tolerance.
6.7 Form tolerances
6.7.1 General
The form tolerances given in 6.7.2 to 6.7.4 shall apply to the following:
a) rod and bar only; if necessary, form tolerances for wire shall be agreed between the supplier and
the purchaser;
b) diameters, widths across-flats or widths of bar equal to or greater than 10 mm;
c) all material conditions except D and H035/R200 (annealed).
The deviation shall be measured with the rod or bar supported on a horizontal reference plane, such
that the deviation is minimized by the mass of the rod or bar.
6.7.2 Twist
Square or hexagonal rod and bar shall conform to the twist tolerances given in Table 10 (see 6.7.1).
The twist v shall be measured as indicated in Figure 4.
13
---------------------- Page: 15 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
Key
1 reference plane
a thickness
b width
v twist
Figure 4 — Measurement of twist
6.7.3 Straightness
Rod and bar shall conform to the straightness tolerances given in Table 11 (see 6.7.1).
The deviations from straightness h and h shall be measured as indicated in Figure 5.
1 2
Key
1 reference plane
h , h deviations from straightness
1 2
l , l
measuring lengths
1 2
Figure 5 — Measurement of straightness
14
---------------------- Page: 16 ----------------------
SIST EN 13601:2021
EN 13601:2021 (E)
6.7.4 Flatness of bar
Bars shall conform to the flatness tolerances given in Table 12 (see 6.7.1).
The deviation from flatness e of bar (thickness a, width b) shall be measured as indicated in Figure 6.
Key
1 reference plane
a thickness
b width
e deviation from flatness
Figure 6 — Measurement of flatness
6.8 Wire in coils
The type of coil, its inside and/or outside diameter, its width or its mass shall be spec
...
SLOVENSKI STANDARD
oSIST prEN 13601:2020
01-april-2020
Baker in bakrove zlitine - Drogovi, palice in žice za splošno uporabo v
elektrotehniki
Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
Kupfer und Kupferlegierungen - Stangen und Drähte aus Kupfer für die allgemeine
Anwendung in der Elektrotechnik
Cuivre et alliages de cuivre - Barres et fils en cuivre pour usages électriques généraux
Ta slovenski standard je istoveten z: prEN 13601
ICS:
77.150.30 Bakreni izdelki Copper products
oSIST prEN 13601:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13601:2020
---------------------- Page: 2 ----------------------
oSIST prEN 13601:2020
DRAFT
EUROPEAN STANDARD
prEN 13601
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2020
ICS 77.150.30 Will supersede EN 13601:2013
English Version
Copper and copper alloys - Copper rod, bar and wire for
general electrical purposes
Cuivre et alliages de cuivre - Barres et fils en cuivre Kupfer und Kupferlegierungen - Stangen und Drähte
pour usages électriques généraux aus Kupfer für die allgemeine Anwendung in der
Elektrotechnik
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 133.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13601:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designations . 7
4.1 Material . 7
4.1.1 General. 7
4.1.2 Symbol . 7
4.1.3 Number . 7
4.2 Material condition . 8
4.3 Product . 8
5 Ordering information . 10
6 Requirements . 11
6.1 Composition . 11
6.2 Mechanical properties . 11
6.3 Bending characteristics . 11
6.4 Electrical properties . 11
6.5 Freedom from hydrogen embrittlement . 11
6.6 Dimensions and tolerances . 11
6.6.1 Diameter or width across-flats . 11
6.6.2 Corner configuration . 12
6.6.3 Length. 13
6.7 Form tolerances . 13
6.7.1 General. 13
6.7.2 Twist . 13
6.7.3 Straightness . 14
6.7.4 Flatness of bar . 14
6.8 Wire in coils . 15
6.9 Mass tolerances . 15
6.10 Surface condition . 15
7 Sampling . 15
7.1 General. 15
7.2 Analysis . 15
7.3 Mechanical and electrical tests . 16
8 Test methods . 16
8.1 Analysis . 16
8.2 Tensile test . 16
8.3 Hardness test . 16
8.4 Bend test . 16
8.5 Electrical resistivity test . 16
2
---------------------- Page: 4 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
8.6 Hydrogen embrittlement test . 17
8.7 Retests . 17
8.8 Rounding of results . 17
9 Declaration of conformity and inspection documentation . 17
9.1 Declaration of conformity . 17
9.2 Inspection documentation . 17
10 Marking, packaging, labelling . 17
Annex A (informative) Characteristics of coppers for electrical purposes . 26
A.1 General grouping of copper types . 26
A.2 General characteristics . 26
A.3 Particular characteristics . 26
Bibliography . 28
3
---------------------- Page: 5 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
European foreword
This document (prEN 13601:2020) has been prepared by Technical Committee CEN/TC 133 “Copper
and copper alloys”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN enquiry.
This document will supersede EN 13601:2013.
In comparison with the previous edition, the following technical modifications have been made:
• maximum diameters or widths across flats for bar, square, hexagonal and rectangular have been
expanded;
• scope clause has been modified;
• in Clause 6.5 Freedom from hydrogen embrittlement, the alloys Cu-OFE (CW009A) and Cu-PHCE
(CW022A) have been added;
• Table 3 has been modified to correct incongruent values;
• tolerances on width and thickness of bar and rectangular wire and maximum twist of square or
hexagonal rod or rectangular bar have been modified (see Table 6 and Table 10).
4
---------------------- Page: 6 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
Introduction
The products specified in this document are those which are especially suitable for electrical purposes,
i.e. with specified electrical properties. Copper rod, bar and wire for general purposes are specified in
EN 12163, EN 12166 and EN 12167.
Annex A (informative) gives guidance on the characteristics of coppers for electrical purposes.
This is one of a series of European Standards for copper products for electrical purposes. Other copper
products are specified as follows:
• EN 13599, Copper and copper alloys — Copper plate, sheet and strip for electrical purposes
• EN 13600, Copper and copper alloys — Seamless copper tubes for electrical purposes
• EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical
conductors
• EN 13604, Copper and copper alloys — Semiconductor devices, electronic and vacuum products made
from high conductivity copper
• EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes
5
---------------------- Page: 7 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
1 Scope
This document specifies the composition, property requirements including electrical properties, and
tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross-
sections and size ranges are:
• round, square and hexagonal rod with diameters or widths across-flats from 2 mm up to and
including 160 mm;
• bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and
including 250 mm;
• round, square, hexagonal and rectangular wire with diameters or widths across-flats from 2 mm up
to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths
from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this
document are also specified.
NOTE Drawn, round copper wire — plain or tinned, single or multiline — for the manufacture of electrical
conductors is specified in EN 13602.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1655, Copper and copper alloys - Declarations of conformity
EN 1976, Copper and copper alloys - Cast unwrought copper products
EN 10204, Metallic products - Types of inspection documents
EN ISO 2626, Copper - Hydrogen embrittlement test (ISO 2626:1973)
EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1)
EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1)
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO
6892-1)
EN ISO 7438, Metallic materials - Bend test (ISO 7438)
IEC 60468, Method of measurement of resistivity of metallic materials
6
---------------------- Page: 8 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
bar
straight product of uniform rectangular cross-section along its whole length
[SOURCE: EN 12167:2016, 3.2]
3.2
rod
straight product of uniform cross-section along its whole length
[SOURCE: EN 12163:2016, 3.1]
3.3
wire
wound product of uniform cross-section along its whole length
Note 1 to entry: Rectangles may have round or sharp corners.
[SOURCE: EN 12166:2016, 3.1]
3.4
deviation from circular form
difference between the maximum and the minimum diameters measured at any one cross-section of a
round product
[SOURCE: EN 12163:2016, 3.2]
4 Designations
4.1 Material
4.1.1 General
The material is designated either by symbol or by number (see Table 1 and Table 2).
4.1.2 Symbol
The material symbol designation is based on the designation system given in ISO 1190-1.
NOTE Although material symbol designations used in this standard might be the same as those in other
standards using the designation system given in ISO 1190-1, the detailed composition requirements are not
necessarily the same.
4.1.3 Number
The material number designation is in accordance with the system given in EN 1412.
7
---------------------- Page: 9 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
4.2 Material condition
For the purposes of this document, the following designations, which are in accordance with the system
given in EN 1173, apply for the material condition:
D Material condition for the product as cold worked without specified mechanical properties;
H. Material condition designated by the minimum value of hardness requirement for the
product with mandatory hardness requirements;
R. Material condition designated by the minimum value of tensile strength requirement for the
product with mandatory tensile strength, 0,2 % proof strength and elongation
requirements.
Products in the H. condition may be specified to Vickers or Brinell hardness. The material condition
designation H. is the same for both hardness test methods.
Exact conversion between the material conditions designated H. and R. is not possible.
Material condition is designated by only one of the above designations.
4.3 Product
The product designation provides a standardized pattern of designation from which a rapid and
unequivocal description of a product can be conveyed in communication. It provides mutual
comprehension at the international level with regard to products which meet the requirements of the
relevant European Standard.
The product designation is no substitute for the full content of the standard.
The product designation for products to this document shall consist of:
a) denomination (rod, bar or wire);
b) number of this European Standard (EN 13601);
c) material designation, either symbol or number (see Table 1 and Table 2);
d) material condition designation (see Table 3);
e) cross-sectional shape (the following designations shall be used as appropriate: RND for round, SQR
for square, HEX for hexagonal);
f) nominal cross-sectional dimensions:
1) round rod or wire: diameter;
2) square or hexagonal rod or wire: width across-flats;
3) bar or rectangular wire: thickness × width;
g) tolerance class for round, square or hexagonal rod or wire (see Table 4);
h) corner type for square or hexagonal rod, bar or rectangular wire (the following designations shall
be used as appropriate: SH for sharp, RD for rounded, CE for semi-circular edges) (see 6.6.2).
The derivation of a product designation is shown in Example 1 and other typical product designations
are shown in Example 2 and Example 3.
8
---------------------- Page: 10 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
EXAMPLE 1 Rod for electrical purposes conforming to this standard, in material designated either Cu-ETP or
CW004A, in material condition H085, round, with nominal diameter 15 mm and tolerance Class A, will be
designated as follows:
Rod — EN 13601 — Cu-ETP — H085 — RND15A
or
Rod — EN 13601 — CW004A — H085 — RND15A
Denomination
Number of this European Standard
Material designation
Material condition designation
Cross-sectional shape, nominal cross-sectional
dimension in millimetres, tolerance class
EXAMPLE 2 Bar for electrical purposes conforming to this standard, in material designated either CuAg0,10 or
CW013A, in material condition R280, rectangular, nominal thickness 15 mm, nominal width 100 mm, semi-
circular edge, will be designated as follows:
Bar EN 13601 — CuAg0,10 — R280 — 15 × 100 — CE
or
Bar EN 13601 — CW013A— R280 — 15 × 100 — CE
EXAMPLE 3 Wire for electrical purposes conforming to this standard, in material designated either Cu-OF or
CW008A, in material condition H035, hexagonal, with nominal width across-flats 8 mm, tolerance Class B and
sharp corners, will be designated as follows:
Wire EN 13601 — Cu-OF— H035 — HEX8B — SH
or
Wire EN 13601 — CW008A — H035 — HEX8B — SH
9
---------------------- Page: 11 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
5 Ordering information
In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser
and the supplier, the purchaser shall state on his enquiry and order the following information:
a) quantity of product required (mass, number of rods or bars or coils of wire);
b) denomination (rod, bar or wire);
c) number of this European Standard (EN 13601);
d) material designation (see Table 1 and Table 2);
e) material condition designation (see 4.2 and Table 3);
f) cross-sectional shape (round, square, hexagonal or rectangular);
g) nominal dimensions (diameter, width across-flats or thickness × width);
h) tolerance class for round, square or hexagonal rod or wire: either Class A (minus tolerance only) or
Class B (plus/minus tolerance) (see Table 4);
i) type of corner (see 6.6.2);
j) for rod or bar, the length required (see 6.6.3);
k) for wire, the coil type: pancake, traverse wound, bunch or on drums (see 6.8);
l) coil size requirements: inside and/or outside diameter and width or mass.
It is recommended that the product designation, as described in 4.3, is used for b) to i).
In addition, the purchaser shall also state on the enquiry and order any of the following, if required:
m) test method to be used for measurement of hardness, i.e. Brinell or Vickers (see 8.3) unless the test
method is to be left to the discretion of the supplier;
n) whether sawn or sheared ends are required (see 6.6.3);
o) whether special surface conditions are required (see 6.10);
p) whether a bend test is required (see 6.3);
q) whether form tolerances for wire are required (see 6.7.1);
r) whether length of wire is required (see 6.6.3);
s) whether sampling is required (see Clause 7);
t) whether a declaration of conformity is required (see 9.1);
u) whether an inspection document is required, and if so, which type (see 9.2);
v) whether there are any special requirements for marking, packaging or labelling (see Clause 10).
10
---------------------- Page: 12 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
EXAMPLE 1 Ordering details for 250 pieces bar for general electrical purposes conforming to EN 13601, in
material designated either CuAg0,10 or CW013A, in material condition R280, rectangular, nominal thickness
15 mm, nominal width 100 mm, semi-circular edge, fixed length 4 500 mm:
250 pieces Bar EN 13601— CuAg0,10 — R280 — 15 × 100 — CE— 4500 FL
or
250 pieces Bar EN 13601— CW013A — R280 — 15 × 100 — CE—4500 FL
EXAMPLE 2 Ordering details for 1 000 kg wire for general electrical purposes conforming to EN 13601, in
material designated either Cu-OF or CW008A, in material condition H035, hexagonal, nominal width across flats
8 mm, tolerance Class B, with sharp corners, nominal inside diameter of coil 500 mm:
1 000 kg Wire EN 13601— Cu-OF — H035 — HEX8B — SH— nominal inside diameter of coil 500 mm
or
1 000 kg Wire EN 13601— CW008A — H035 — HEX8B — SH— nominal inside diameter of coil
500 mm
6 Requirements
6.1 Composition
The composition shall conform to the requirements for the appropriate material given in Table 1 and
Table 2.
NOTE For characteristics of coppers for electrical purposes, see Annex A.
6.2 Mechanical properties
The mechanical properties shall conform to the appropriate requirements given in Table 3. The tests
shall be carried out in accordance with either 8.2 (tensile test) or 8.3 (hardness test).
6.3 Bending characteristics
If required, bending characteristics shall be agreed between the purchaser and the supplier at the time
of enquiry and order. The test shall be carried out in accordance with 8.4.
6.4 Electrical properties
The electrical properties shall conform to the appropriate requirements given in Table 4. The test shall
be carried out in accordance with 8.5.
6.5 Freedom from hydrogen embrittlement
Rod, bar and wire in copper grades Cu-OF (CW008A), Cu-OFE (CW009A), CuAg0,04P (CW014A),
CuAg0,07P (CW015A), CuAg0,10P (CW016A), CuAg0,04(OF) (CW017A), CuAg0,07(OF) (CW018A),
CuAg0,10(OF) (CW019A), Cu-PHC (CW020A), Cu-HCP (CW021A) and Cu-PHCE (CW022A) shall show
no evidence of cracking, when tested and visually examined in accordance with 8.6.
6.6 Dimensions and tolerances
6.6.1 Diameter or width across-flats
The diameter or width across-flats of round, square, hexagonal or rectangular rod, bar or wire shall
conform to the appropriate tolerances given in Table 5 and Table 6.
11
---------------------- Page: 13 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
6.6.2 Corner configuration
6.6.2.1 General
Rod, bar and wire may be supplied with sharp corners, rounded corners or semi-circular edges. The
type of corner shall be specified at the time of order [see Clause 5 list entry i)].
6.6.2.2 Sharp corners
Sharp corners (SH) of square, hexagonal and rectangular rod, bar and wire (see Figure 1) shall conform
to Table 7.
Figure 1 — Sharp corner
6.6.2.3 Rounded corners
Rounded corners (RD) of square, hexagonal and rectangular rod, bar and wire (see Figure 2) shall
conform to Table 8.
Figure 2 — Rounded corner
6.6.2.4 Semi-circular edge
The radius of semi-circular edges (CE) of rectangular bar and wire (see Figure 3) is half the thickness
and shall conform to a tolerance of ± 20 % of the radius; the arc of curvature shall merge smoothly into
the adjacent flat side and shall be free from sharp, rough or projecting corners.
12
---------------------- Page: 14 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
Figure 3 — Semi-circular edge
6.6.3 Length
6.6.3.1 General
Rod and bar shall be supplied either in manufactured length (ML) or fixed length (FL), with ends either
sawn or sheared.
If required, the length of wire shall be agreed between the purchaser and the supplier.
6.6.3.2 Manufactured lengths (ML)
Manufactured lengths (ML) shall be supplied in the nominal lengths. The tolerances are by agreement
between the purchaser and the supplier.
It is permissible for 10 % of the number of rods and bars in a consignment to be shorter, but not less
than 50 % of the nominal length.
6.6.3.3 Fixed lengths (FL)
The lengths supplied as fixed lengths shall conform to the tolerances given in Table 9.
The deviation from squareness of the cut shall be a maximum of 2 % of the diameter or width or major
across-flats dimension of the rod and bar and is included in the fixed length tolerance.
6.7 Form tolerances
6.7.1 General
The form tolerances given in 6.7.2 to 6.7.4 shall apply to the following:
a) rod and bar only; if necessary, form tolerances for wire shall be agreed between the supplier and
the purchaser;
b) diameters, widths across-flats or widths of bar equal to or greater than 10 mm;
c) all material conditions except D and H035/R200 (annealed).
The deviation shall be measured with the rod or bar supported on a horizontal reference plane, such
that the deviation is minimized by the mass of the rod or bar.
6.7.2 Twist
Square or hexagonal rod and bar shall conform to the twist tolerances given in Table 10 (see 6.7.1).
The twist v shall be measured as indicated in Figure 4.
13
---------------------- Page: 15 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
Key
1 reference plane
a thickness
b width
v twist
Figure 4 — Measurement of twist
6.7.3 Straightness
Rod and bar shall conform to the straightness tolerances given in Table 11 (see 6.7.1).
The deviations from straightness h and h shall be measured as indicated in Figure 5.
1 2
Key
1 reference plane
h , h deviations from straightness
1 2
l1, l2 measuring lengths
Figure 5 — Measurement of straightness
6.7.4 Flatness of bar
Bars shall conform to the flatness tolerances given in Table 12 (see 6.7.1).
The deviation from flatness e of bar (thickness a, width b) shall be measured as indicated in Figure 6.
14
---------------------- Page: 16 ----------------------
oSIST prEN 13601:2020
prEN 13601:2020 (E)
Key
1 reference plane
a thickness
b width
e deviation from
flatness
Figure 6 — Measurement of flatness
6.8 Wire in coils
The type of coil, its inside and/or outside diameter, its
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.