SIST EN 12697-21:2012
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
This European Standard specifies a test method for measuring the indentation of mastic asphalt when it is penetrated at a given temperature, load and for a fixed time period by a standardised cylindrical indentor pin with a circular flat-ended base. This European Standard applies to mastic asphalt with aggregates of maximum nominal size less or equal to 16 mm.
Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an Platten
Die vorliegende Europäische Norm legt ein Prüfverfahren zur Messung der Eindringtiefe in Guss¬asphalt fest, wenn bei einer festgelegten Temperatur, einer festgelegten Beanspruchung und für eine bestimmte Zeit ein genormter zylindrischer Prüfstempel mit einer kreisrunden flachen Grundfläche in diesen Asphalt eindringt. Diese Europäische Norm gilt für Gussasphalt mit einer maximalen Nennkorngröße gleich oder kleiner als 16 mm.
Mélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 21: Essai d'indentation de plaques
La présente Norme européenne spécifie une méthode d’essai permettant de mesurer l’indentation d’un asphalte coulé lorsqu’il est soumis à la pénétration d’un poinçon normalisé cylindrique à embout plat circulaire, à des valeurs données de température et de charge et pour un temps d’application fixé. Cette Norme européenne s’applique à des asphaltes coulés dont la dimension nominale maximale des granulats est inférieure ou égale à 16 mm.
Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 21. del: Preskus z vtiskanjem na plošče
Ta evropski standard določa preskusno metodo za merjenje vtisa v litem asfaltu, ko se prebada pri določeni temperaturi in bremenu ter v določenem časovnem obdobju s standardiziranim valjastim vtisnim sornikom z okroglo ploščato osnovo. Ta evropski standard se uporablja za liti asfalt z agregati z največjo nominalno velikostjo, ki je manjša ali enaka 16 mm.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an PlattenMélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 21: Essai d'indentation de plaquesBituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-21:2012SIST EN 12697-21:2012en,fr,de01-junij-2012SIST EN 12697-21:2012SLOVENSKI
STANDARDSIST EN 12697-21:2004/AC:2007SIST EN 12697-21:20041DGRPHãþD
SIST EN 12697-21:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-21
April 2012 ICS 93.080.20 Supersedes EN 12697-21:2003English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 21: Essai d'indentation de plaques
Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an Platten This European Standard was approved by CEN on 26 February 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-21:2012: ESIST EN 12697-21:2012
EN 12697-21:2012 (E) 2 Contents Page Foreword .31Scope .72Normative references .73Apparatus .73.1Moulding of test plates of mastic asphalt .73.2Apparatus for the indentation test .74Sampling and preparation of laboratory sample .84.1Sampling .84.2Preparation of the samples .85Procedure .96Calculation and expression of results .97Precision . 108Test report . 10Bibliography . 11 SIST EN 12697-21:2012
EN 12697-21:2012 (E) 3 Foreword This document (EN 12697-21:2012) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12697-21:2003. The following is a list of significant technical changes since the last edition: test cubes renamed as test plates and height of cylindrical specimens defined; the system to apply the load clarified, including that the equipment is suitable; pneumatic thrusters redefined as pneumatic actuator; clarification that the water bath only has to be capable of maintaining the temperature in the vicinity of the sample; in the preparation of samples, the temperature of mastic asphalt with modified binders and/or for low temperature mastic asphalt shall be in accordance with the producer’s instructions; requirement added about the storage of specimens prior to the start of testing from the time of their manufacture. This European Standard is one of a series of standards as listed below: EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays SIST EN 12697-21:2012
EN 12697-21:2012 (E) 4 EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or cylindrical specimens EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor SIST EN 12697-21:2012
EN 12697-21:2012 (E) 5 EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared by roller compactor EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test EN 12697-35, Bituminous mixtures — Test meth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.