SIST EN ISO 4254-1:2013
(Main)Agricultural machinery - Safety - Part 1: General requirements (ISO 4254-1:2013)
Agricultural machinery - Safety - Part 1: General requirements (ISO 4254-1:2013)
This part of ISO 4254 specifies the safety requirements and the means of their verification for the design and construction of self-propelled ride-on machines, mounted, semi-mounted and trailed machines used in agriculture in order to deal with the hazards which are typical for most of the machines. In addition, it specifies the type of information on safe working practices including information about residual risks to be provided by the manufacturer. This document deals with significant hazards, hazardous situations and events, as listed in Annex A, relevant to this agricultural machinery when used as intended and under the conditions of misuse foreseeable by the manufacturer during normal operation and service. This part of ISO 4254 is not applicable to
— agricultural or forestry tractors,
— aircraft and air-cushion vehicles used in agriculture,
— lawn and garden equipment,
— machine-specific components or functions (e.g. working tools and/or processes). This part of ISO 4254 is not applicable to hazards related to periodic service, machine conversion and
repairs intended to be carried out by professional service personnel, environmental hazards, road safety (e.g. steering, braking), or to the power take-off (PTO) drive shaft; neither is it applicable to guards of moving parts for power transmission except for strength requirements for guards and barriers. This part of ISO 4254 is not applicable to machines which are manufactured before the date of its publication. Not all of the hazards dealt with by this part of ISO 4254 are necessarily present on a particular machine. A risk assessment should be carried out by the manufacturer to determine the hazards that are applicable and any hazards in addition to those dealt with by this part or a relevant machine-specific part. The requirements of a machine-specific part of ISO 4254 take precedence over the requirements of this part.
Landmaschinen - Sicherheit - Teil 1: Generelle Anforderungen (ISO 4254-1:2013)
Dieser Teil von ISO 4254 legt sicherheitstechnische Anforderungen und deren Überprüfung für die Gestaltung
und Konstruktion von selbstfahrenden Landmaschinen mit Fahrersitz und angebauten, aufgesattelten oder
gezogenen Landmaschinen, die in der Landwirtschaft eingesetzt werden, um die Gefährdungen zu
behandeln, die für die meisten Maschinen typisch sind fest. Zusätzlich legt er fest, welche Informationen zum
sicheren Betrieb (einschließlich Restgefahren) vom Hersteller zur Verfügung zu stellen sind.
Dieser Teil von ISO 4254 behandelt signifikante Gefährdungen (siehe Anhang A), Gefährdungssituationen
und Gefährdungsereignisse, die für diese Landmaschinen, die bestimmungsgemäß und unter den vom
Hersteller vorgesehenen Bedingungen im Rahmen des normalen Betriebes und Routineservicearbeiten
eingesetzt werden, relevant sind (siehe Abschnitt 4).
Dieser Teil von ISO 4254 findet keine Anwendung auf:
⎯ Land- oder forstwirtschaftliche Traktoren,
⎯ Luftfahrzeuge,
⎯ Luftkissenfahrzeuge,
⎯ Rasen- und Gartengeräte,
⎯ Maschinen-spezifische Bauteile oder Funktionen, z. B. Arbeitswerkzeuge und/oder -prozesse.
Dieser Teil von ISO 4254 gilt nicht für Gefährdungen in Hinblick auf turnusmäßigen Servicearbeiten,
Umrüstung oder Umbauten von Maschinen, von Fachservicekräften durchzuführende Reparaturarbeiten, die
Umwelt, den Straßenverkehr oder Gelenkwellen; er gilt ebenfalls nicht für Schutzeinrichtungen für bewegliche
Teile der Kraftübertragung mit Ausnahme der Festigkeitsanforderungen an Schutzeinrichtungen und Abweisbügel
(siehe 4.9).
Dieser Teil von ISO 4254 gilt nicht für Maschinen, die vor dem Veröffentlichungsdatum hergestellt wurden.
Alle in diesem Teil von ISO 4254 behandelten Gefährdungen sind nicht notwendigerweise an einer
spezifische Maschine vorhanden. Eine Maschine kann auch spezifische Gefährdungen aufweisen, z. B. in
Bezug auf Arbeitswerkzeuge und/oder -prozesse, die nicht in diesem Teil von ISO 4254 behandelt werden. In
Bezug auf alle von diesem Teil von ISO 4254 erfassten Maschinen gilt: die Festlegungen des Teiles von
ISO 4254, sofern vorhanden, der direkt auf den jeweiligen Maschinetyp anzuwenden ist, haben Vorrang vor
den Festlegungen dieses Teiles von ISO 4254.
Matériel agricole - Sécurité - Partie 1: Exigences générales (ISO 4254-1:2013)
Kmetijski stroji - Varnost - 1. del: Splošne zahteve (ISO 4254-1:2013)
Ta del standarda ISO 4254 določa varnostne zahteve in način njihovega preverjanja za zasnovo in izdelavo samognanih strojev s sedežem, priklopnih, polpriklopnih in vlečenih strojev, ki se uporabljajo v kmetijstvu, z namenom obravnave tveganj, ki so značilna za večino vrst strojev. Določa tudi vrsto informacij o varnih delovnih praksah, vključno z informacijami o ostalih tveganjih, ki jih mora zagotoviti proizvajalec. Ta dokument obravnava večja tveganja, nevarne razmere in dogodke, opisane v dodatku A, ki so pomembni za te kmetijske stroje, ko se med normalnim delovanjem in vzdrževanjem uporabljajo v skladu z njihovim namenom in pod pogoji pričakovane nepravilne uporabe, ki jih določa proizvajalec. Ta del standarda ISO 4254 se ne uporablja za:
– kmetijske ali gozdarske traktorje,
– letala ali vozila z zračno blazino, ki se uporabljajo v kmetijstvu,
– kosilnice ali vrtno opremo,
– dele ali funkcije, ki so specifične za stroj (npr. delovna orodja in/ali postopki).
Ta del standarda ISO 4254 se ne uporablja za tveganja, ki so povezana z rednim vzdrževanjem, predelavo stroja in popravili, ki jih izvaja profesionalno servisno osebje, okoljskimi tveganji, cestno varnostjo (npr. krmiljenjem, zaviranjem) ali pogonsko gredjo za prenos moči (PTO); ne uporablja se tudi za zaščitne ali gibajoče se dele menjalnika, razen za zahteve glede trdnosti ščitnikov in pregrad. Ta del standarda ISO 4254 se ne uporablja za stroje, izdelane pred datumom njegove objave. Vsa tveganja, ki jih obravnava ta del standarda ISO 4254, niso nujna za določeni stroj. Proizvajalec mora izvesti oceno tveganja, da ugotovi morebitna tveganja in dodatna tveganja poleg tveganj, ki jih obravnava ta del standarda ali ustrezen del, ki je povezan z določenim strojem. Zahteve dela standarda ISO 4254, ki je povezan z določenim strojem, imajo prednost pred zahtevami tega dela.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4254-1:2013
01-junij-2013
1DGRPHãþD
SIST EN ISO 4254-1:2010
SIST EN ISO 4254-1:2010/AC:2011
Kmetijski stroji - Varnost - 1. del: Splošne zahteve (ISO 4254-1:2013)
Agricultural machinery - Safety - Part 1: General requirements (ISO 4254-1:2013)
Landmaschinen - Sicherheit - Teil 1: Generelle Anforderungen (ISO 4254-1:2013)
Matériel agricole - Sécurité - Partie 1: Exigences générales (ISO 4254-1:2013)
Ta slovenski standard je istoveten z: EN ISO 4254-1:2013
ICS:
65.060.01 Kmetijski stroji in oprema na Agricultural machines and
splošno equipment in general
SIST EN ISO 4254-1:2013 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4254-1:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 4254-1:2013
EUROPEAN STANDARD
EN ISO 4254-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2013
ICS 65.060.01 Supersedes EN ISO 4254-1:2009
English Version
Agricultural machinery - Safety - Part 1: General requirements
(ISO 4254-1:2013)
Matériel agricole - Sécurité - Partie 1: Exigences générales Landmaschinen - Sicherheit - Teil 1: Generelle
(ISO 4254-1:2013) Anforderungen (ISO 4254-1:2013)
This European Standard was approved by CEN on 25 April 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4254-1:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 4254-1:2013
EN ISO 4254-1:2013 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5
2
---------------------- Page: 4 ----------------------
SIST EN ISO 4254-1:2013
EN ISO 4254-1:2013 (E)
Foreword
This document (EN ISO 4254-1:2013) has been prepared by Technical Committee ISO/TC 23 "Tractors and
machinery for agriculture and forestry" in collaboration with Technical Committee CEN/TC 144 “Tractors and
machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2013, and conflicting national standards shall be withdrawn
at the latest by November 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4254-1:2009.
This third edition cancels and replaces the second edition (EN ISO 4254-1:2009), which has been technically
revised.
The following major changes were introduced:
requirements related the protection from moving parts involved in the work have been added in 4.2;
requirements related to vibration have been added in 4.3;
requirements related to automatic mode of operation have been added in 4.6;
requirements related to foldable barriers have been added in 4.9;
requirements related to operating fluids have been added in 4.15;
requirements related to emergency stop controls have been added in 4.19;
requirements related to safety related parts of control systems have been added in 4.20;
requirements related to roll-over and tip-over hazards have been added in 5.7;
requirements related to PTO drive shaft guard clearance have been added in 6.4.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive
2006/42/EC. It is intended to be used together with EN 15811:2009 "Agricultural machinery – Guards for
moving parts of power transmission – Guard opening with tool (ISO/TS 28923:2007 modified)".
NOTE It is intended to replace EN 15811:2009 by a new edition based on ISO/TS 28923:2012.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 4254-1:2013
EN ISO 4254-1:2013 (E)
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4254-1:2013 has been approved by CEN as EN ISO 4254-1:2013 without any modification.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 4254-1:2013
EN ISO 4254-1:2013 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements of that Directive and associated EFTA regulations, except Essential
Requirements 1.7.3 and 3.6.2.
NOTE Compliance with EN ISO 4254-1 and a machine-specific part of EN ISO 4254 is required to achieve
presumption of conformity with the corresponding Essential Requirements of the Directive and associated EFTA
regulations. Conformity with ESR 1.7.4.2 u) 4th paragraph, 2nd sentence (uncertainty of noise measurement) can only be
claimed if the relevant machine-specific part of EN ISO 4254 includes specifications of the noise measurement
uncertainty.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
5
---------------------- Page: 7 ----------------------
SIST EN ISO 4254-1:2013
---------------------- Page: 8 ----------------------
SIST EN ISO 4254-1:2013
INTERNATIONAL ISO
STANDARD 4254-1
Fifth edition
2013-05-01
Agricultural machinery — Safety —
Part 1:
General requirements
Matériel agricole — Sécurité —
Partie 1: Exigences générales
Reference number
ISO 4254-1:2013(E)
©
ISO 2013
---------------------- Page: 9 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Safety requirements and/or measures applicable to all machines.5
4.1 Fundamental principles, design guidance . 5
4.2 Protection from moving parts involved in the work . 5
4.3 Noise . 5
4.4 Vibration . 6
4.5 Controls . 6
4.6 Automatic mode of operation . 7
4.7 Operator stations . 7
4.8 Other than operator stations .10
4.9 Folding elements .12
4.10 Strength requirements for guards and barriers .12
4.11 Supports for service and maintenance.12
4.12 Electric equipment .13
4.13 Hydraulic components and fittings .13
4.14 Pneumatic systems .13
4.15 Operating fluids .13
4.16 Manual operation of individual assemblies .14
4.17 Service and handling of machine parts .14
4.18 Electromagnetic compatibility .14
4.19 Emergency stop .14
4.20 Safety-related parts of control systems .15
5 Safety requirements and/or measures — Self-propelled ride-on machines .15
5.1 Operator station .15
5.2 Moving the machine .18
5.3 Electric .19
5.4 Fuel tank .19
5.5 Hot surfaces .19
5.6 Exhaust gases .19
5.7 Roll- and tip-over .19
6 Safety requirements and/or measures — Mounted, semi-mounted and trailed machines 20
6.1 Controls .20
6.2 Stability .20
6.3 Hitches for towing .21
6.4 Transmission of mechanical power between self-propelled machines/tractors and
recipient machinery .21
6.5 Hydraulic, pneumatic and electrical connections with a self-propelled machine or
towing vehicle .22
7 Verification of safety requirements or protective measures .22
8 Information for use .23
8.1 General .23
8.2 Operator’s manual.23
8.3 Safety and instructional signs .24
8.4 Marking .25
Annex A (informative) List of significant hazards.26
Annex B (normative) Noise test code (engineering method grade 2) .30
© ISO 2013 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
Annex C (normative) Strength tests.34
Annex D (informative) Stability of tractor machine combinations .36
Bibliography .38
iv © ISO 2013 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 3, Safety and comfort.
This fifth edition of ISO 4254-1 cancels and replaces the fourth edition (ISO 4254-1:2008), which has
been technically revised. In particular, requirements relating to the following have been introduced:
— vibrations;
— protection of moving parts;
— operation of machine parts;
— operating fluids;
— foldable barriers;
— PTO drive shaft guard clearance;
— emergency stop controls;
— safety related parts of control systems;
— roll-over and tip-over hazards.
ISO 4254 consists of the following parts, under the general title Agricultural machinery — Safety:
— Part 1: General requirements
— Part 5: Power-driven soil-working machines
— Part 6: Sprayers and liquid fertilizer distributors
— Part 7: Combine harvesters, forage harvesters and cotton harvesters
— Part 8: Solid fertilizer distributors
— Part 9: Seed drills
— Part 10: Rotary tedders and rakes
© ISO 2013 – All rights reserved v
---------------------- Page: 13 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
— Part 11: Pick-up balers
— Part 12: Rotary disc and drum mowers and flail mowers
— Part 13: Large rotary mowers
ISO 4254-2, Anhydrous ammonia applicators, has been withdrawn.
ISO 4254-3, Tractors, has been cancelled and replaced by ISO 26322 (all parts), Tractors for agriculture
and forestry — Safety.
ISO 4254-4, Tractors and machinery for agriculture and forestry — Technical means for providing safety —
Part 4: Forestry winches, has been cancelled and replaced by ISO 19472, Machinery for forestry —
Winches — Dimensions, performance and safety.
vi © ISO 2013 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
Introduction
This document is a type-C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered
are indicated in the scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or
type-B standards, the requirements of this type-C standard take precedence over the requirements of
the other standards for machines that have been designed and built according to the requirements of
this type-C standard.
© ISO 2013 – All rights reserved vii
---------------------- Page: 15 ----------------------
SIST EN ISO 4254-1:2013
---------------------- Page: 16 ----------------------
SIST EN ISO 4254-1:2013
INTERNATIONAL STANDARD ISO 4254-1:2013(E)
Agricultural machinery — Safety —
Part 1:
General requirements
1 Scope
This part of ISO 4254 specifies the safety requirements and the means of their verification for the design
and construction of self-propelled ride-on machines, mounted, semi-mounted and trailed machines used
in agriculture in order to deal with the hazards which are typical for most of the machines. In addition,
it specifies the type of information on safe working practices including information about residual risks
to be provided by the manufacturer.
This document deals with significant hazards, hazardous situations and events, as listed in Annex A,
relevant to this agricultural machinery when used as intended and under the conditions of misuse
foreseeable by the manufacturer during normal operation and service.
This part of ISO 4254 is not applicable to
— agricultural or forestry tractors,
— aircraft and air-cushion vehicles used in agriculture,
— lawn and garden equipment,
— machine-specific components or functions (e.g. working tools and/or processes).
This part of ISO 4254 is not applicable to hazards related to periodic service, machine conversion and
repairs intended to be carried out by professional service personnel, environmental hazards, road safety
(e.g. steering, braking), or to the power take-off (PTO) drive shaft; neither is it applicable to guards of
moving parts for power transmission except for strength requirements for guards and barriers.
This part of ISO 4254 is not applicable to machines which are manufactured before the date of its publication.
Not all of the hazards dealt with by this part of ISO 4254 are necessarily present on a particular machine.
A risk assessment should be carried out by the manufacturer to determine the hazards that are applicable
and any hazards in addition to those dealt with by this part or a relevant machine-specific part. The
requirements of a machine-specific part of ISO 4254 take precedence over the requirements of this part.
2 Normative references
The following referenced documents, in whole or in part, are normatively referenced in this document
and are indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 3600:1996, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Operator’s manuals — Content and presentation
ISO 3744:2010, Acoustics — Determination of sound power levels and sound energy levels of noise sources
using sound pressure — Engineering methods for an essentially free field over a reflecting plane
ISO 3767-1:1998, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Symbols for operator controls and other displays — Part 1: Common symbols
© ISO 2013 – All rights reserved 1
---------------------- Page: 17 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
ISO 3767-2:2008, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Symbols for operator controls and other displays — Part 2: Symbols for agricultural tractors and machinery
ISO 3776-1:2006, Tractors and machinery for agriculture — Seat belts — Part 1: Anchorage location requirements
ISO 3776-2:2013, Tractors and machinery for agriculture — Seat belts — Part 2: Anchorage strength requirements
ISO 3776-3:2009, Tractors and machinery for agriculture — Seat belts — Part 3: Requirements for assemblies
ISO 3795:1989, Road vehicles, and tractors and machinery for agriculture and forestry — Determination of
burning behaviour of interior materials
ISO 4253:1993, Agricultural tractors — Operator’s seating accommodation — Dimensions
ISO 4413:2010, Hydraulic fluid power — General rules and safety requirements for systems and their components
ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their components
ISO 5008:2002, Agricultural wheeled tractors and field machinery — Measurement of whole-body vibration
of the operator
ISO 5353:1995, Earth-moving machinery, and tractors and machinery for agriculture and forestry —
Seat index point
ISO 10975:2009, Tractors and machinery for agriculture — Auto-guidance systems for operator-controlled
tractors and self-propelled machines — Safety requirements
ISO 11201:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission
sound pressure levels at a work station and at other specified positions in an essentially free field over a
reflecting plane with negligible environmental corrections
ISO 11204:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission sound
pressure levels at a work station and at other specified positions applying accurate environmental corrections
ISO 11684:1995, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Safety signs and hazard pictorials — General principles
ISO/TR 11688-1:1995, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning
ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 13849-1:2006, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design
ISO 13849-2:2012, Safety of machinery — Safety-related parts of control systems — Part 2: Validation
ISO 13850:2006, Safety of machinery — Emergency stop — Principles for design
ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by upper
and lower limbs
ISO 14982:1998, Agricultural and forestry machinery — Electromagnetic compatibility — Test methods
and acceptance criteria
ISO 15077:2008, Tractors and self-propelled machinery for agriculture — Operator controls — Actuating
forces, displacement, location and method of operation
ISO 16231-1:2013, Self-propelled agricultural machinery — Assessment of stability — Part 1: Principles
ISO 25119-1:2010, Tractors and machinery for agriculture and forestry — Safety-related parts of control
systems — Part 1: General principles for design and development
2 © ISO 2013 – All rights reserved
---------------------- Page: 18 ----------------------
SIST EN ISO 4254-1:2013
ISO 4254-1:2013(E)
ISO 25119-2:2010, Tractors and mac
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.