oSIST prEN 14354:2024

Wood-based panels - Wood veneer floor coverings

This document defines terms and specifies requirements and test methods for wood veneer floor coverings for internal use.
This document is not applicable to multilayer parquets according to EN 13489 with a top layer thickness ≥ 2,5 mm and to modular mechanical locked floor covering (MMF) panels with wear resistant top layer according EN 16511.

Holzwerkstoffe - Furnierte Fußbodenbeläge

Dieses Dokument definiert Benennungen und legt Anforderungen und Prüfverfahren für furnierte Fußbodenbeläge zur Verwendung im Innenbereich fest.
Dieses Dokument gilt nicht für Mehrschichtparkett in Übereinstimmung mit EN 13489 mit einer Deckschichtdicke von ≥ 2,5 mm und für modulare mechanisch verriegelnde Bodenbeläge (MMF) mit verschleißfester Deckschicht in Übereinstimmung mit EN 16511.

Panneaux à base de bois - Revêtements de sol à placage bois

Lesne plošče - Furnirane talne obloge

General Information

• Status: Not Published
• Public Enquiry End Date: 24-Dec-2024
• ICS: 79.080 - Semi-manufactures of timber
• ICS: 97.150 - Floor coverings
• Technical Committee: LLZ - Les, lesni izdelki in zaščita lesa
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 08-Oct-2024
• Due Date: 25-Feb-2025
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Mandate: M/119 REV1 - Amendment to mandate to CEN and CENELEC concerning the execution of standardisation work for harmonised standards on floor coverings
• Ref Project: prEN 14354 - Wood-based panels - Wood veneer floor coverings

Relations

• Revises: SIST EN 14354:2017 - Wood-based panels - Wood veneer floor coverings
• Effective Date: 28-Feb-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2024
Lesne plošče - Furnirane talne obloge
Wood-based panels - Wood veneer floor coverings
Holzwerkstoffe - Furnierte Fußbodenbeläge
Panneaux à base de bois - Revêtements de sol à placage bois
Ta slovenski standard je istoveten z: prEN 14354
ICS:
79.080 Polizdelki iz lesa Semi-manufactures of timber
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2024
ICS 79.080 Will supersede EN 14354:2017
English Version
Wood-based panels - Wood veneer floor coverings
Panneaux à base de bois - Revêtements de sol à placage Holzwerkstoffe - Furnierte Fußbodenbeläge
bois
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 112.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14354:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Requirements . 12
4.1 General. 12
4.2 General requirements . 12
5 Classification requirements . 14
5.1 General. 14
5.2 Classification requirements for elements with film-forming coating . 16
6 Additional requirements. 18
7 Measures to extend the life span . 18
7.1 General. 18
7.2 Maintenance . 18
7.3 Local repair . 18
7.4 Renovation and refurbishment . 18
8 Marking and packaging . 19
8.1 Marking . 19
8.2 Packaging . 19
9 Test report . 19
Annex A (normative) Test methods for the determination of thickness, length, width,
squareness, deviation from edge straightness and cup . 21
A.1 General. 21
A.2 Sampling . 21
A.3 Conditioning . 21
A.4 Test equipment . 21
A.5 Procedure . 23
A.5.1 Determination of thickness t . 23
A.5.2 Determination of the thickness (t) of an element with pre-attached underlay . 24
A.5.3 Determination of length l . 24
A.5.4 Determination of width w and dimensions of squared elements . 25
A.5.5 Determination of deviation from squareness q . 25
A.5.6 Determination of deviation of edge straightness s . 26
A.5.7 Determination of cup f . 26
w
A.6 Calculation and expression of results . 26
A.6.1 Thickness t . 26
A.6.2 Width w . 27
A.6.3 Length l . 27
A.6.4 Deviation from squareness q . 27
A.6.5 Deviation from edge straightness s . 27
A.6.6 Cup f . 27
w
A.7 Test report . 27
Annex B (normative) Test method to determine the opening and lipping between elements
................................................................................................................................................................... 29
B.1 General . 29
B.2 Sampling . 29
B.3 Conditioning . 29
B.4 Test equipment. 29
B.5 Procedure . 29
B.5.1 Assembling . 29
B.5.2 Measuring of lipping . 30
B.5.3 Measuring of openings . 30
B.5.4 Calculation and expression of results . 30
B.6 Calculation and expression of results . 30
B.7 Test report . 30
Annex C (normative) Test method to determine the elasticity of lacquer . 31
C.1 General . 31
C.2 Sampling . 31
C.3 Apparatus . 31
C.4 Procedure . 31
C.5 Calculation and expression of results . 31
C.6 Evaluation of results, elasticity classification . 31
Annex D (normative) Determination of the wear resistance using the falling sand method
................................................................................................................................................................... 32
D.1 General . 32
D.2 Sampling . 32
D.3 Conditioning . 32
D.4 Apparatus . 33
D.4.1 Testing machine . 33
D.4.2 Grit feeder and accessories . 33
D.4.3 Additional material or equipment . 37
D.5 Procedure . 38
D.5.1 General . 38
D.5.2 Maintenance of the abrading wheels . 38
D.5.3 Operation of the abrader . 38
D.5.4 Calibration . 39
D.5.5 Abrasion of test specimen . 39
D.6 Expression of results . 41
D.7 Test report . 41
Annex E (normative) Determination of abrasion resistance using the sand paper method 42
E.1 General.
...