SIST EN ISO 3380:2015
(Main)Leather - Physical and mechanical tests - Determination of shrinkage temperature up to 100 degrees C (ISO 3380:2015)
Leather - Physical and mechanical tests - Determination of shrinkage temperature up to 100 degrees C (ISO 3380:2015)
This International Standard specifies a method for determination of the shrinkage temperature of
leather up to 100 °C. It is applicable to all leathers.
Leder - Physikalische und mechanische Prüfungen - Bestimmung der Schrumpfungstemperatur bis 100 °C (ISO 3380:2015)
Cuir - Essais physiques et mécaniques - Détermination de la température de rétrécissement jusqu'à 100 degrés C (ISO 3380:2015)
L'ISO 3380:2015 spécifie une méthode de détermination de la température de rétrécissement du cuir jusqu'à 100 °C. Elle est applicable à tous les cuirs.
Usnje - Fizikalni in mehanski preskusi - Ugotavljanje temperature krčenja do 100 °C (ISO 3380:2015)
Ta mednarodni standard določa metodo za ugotavljanje temperature krčenja
usnja do 100 °C. Uporablja se za vse vrste usnja.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3380:2015
01-december-2015
1DGRPHãþD
SIST EN ISO 3380:2003
8VQMH)L]LNDOQLLQPHKDQVNLSUHVNXVL8JRWDYOMDQMHWHPSHUDWXUHNUþHQMDGRƒ
& ,62
Leather - Physical and mechanical tests - Determination of shrinkage temperature up to
100 degrees C (ISO 3380:2015)
Leder - Physikalische und mechanische Prüfungen - Bestimmung der
Schrumpfungstemperatur bis 100 °C (ISO 3380:2015)
Cuir - Essais physiques et mécaniques - Détermination de la température de
rétrécissement jusqu'à 100 degrés C (ISO 3380:2015)
Ta slovenski standard je istoveten z: EN ISO 3380:2015
ICS:
59.140.30 Usnje in krzno Leather and furs
SIST EN ISO 3380:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3380:2015
---------------------- Page: 2 ----------------------
SIST EN ISO 3380:2015
EN ISO 3380
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2015
EUROPÄISCHE NORM
ICS 59.140.30 Supersedes EN ISO 3380:2002
English Version
Leather - Physical and mechanical tests - Determination of
shrinkage temperature up to 100 °C (ISO 3380:2015)
Cuir - Essais physiques et mécaniques - Détermination Leder - Physikalische und mechanische Prüfungen -
de la température de rétrécissement jusqu'à 100 °C Bestimmung der Schrumpfungstemperatur bis 100 °C
(ISO 3380:2015) (ISO 3380:2015)
This European Standard was approved by CEN on 8 August 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3380:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3380:2015
EN ISO 3380:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3380:2015
EN ISO 3380:2015 (E)
European foreword
This document (EN ISO 3380:2015) has been prepared by Technical Committee CEN/TC 289 “Leather”,
the secretariat of which is held by UNI, in collaboration with Technical Committee IULTCS
“International Union of Leather Technologists and Chemists Societies”.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
This document supersedes EN ISO 3380:2002.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 3380:2015 has been approved by CEN as EN ISO 3380:2015 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 3380:2015
---------------------- Page: 6 ----------------------
SIST EN ISO 3380:2015
INTERNATIONAL ISO
STANDARD 3380
IULTCS/IUP 16
Third edition
2015-09-01
Leather — Physical and mechanical
tests — Determination of shrinkage
temperature up to 100 °C
Cuir — Essais physiques et mécaniques — Détermination de la
température de rétrécissement jusqu’à 100 °C
Reference numbers
ISO 3380:2015(E)
IULTCS/IUP 16:2015(E)
©
ISO 2015
---------------------- Page: 7 ----------------------
SIST EN ISO 3380:2015
ISO 3380:2015(E)
IULTCS/IUP 16:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3380:2015
ISO 3380:2015(E)
IULTCS/IUP 16:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Sampling and sample preparation . 2
6 Procedure. 3
7 Test report . 3
Annex A (informative) Sources of test apparatus . 4
© ISO 2015 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 3380:2015
ISO 3380:2015(E)
IULTCS/IUP 16:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent r
...
SLOVENSKI STANDARD
kSIST FprEN ISO 3380:2015
01-julij-2015
8VQMH)L]LNDOQLLQPHKDQVNLSUHVNXVL8JRWDYOMDQMHWHPSHUDWXUHNUþHQMDGRƒ
& ,62)',6
Leather - Physical and mechanical tests - Determination of shrinkage temperature up to
100 degrees C (ISO/FDIS 3380:2015)
Leder - Physikalische und mechanische Prüfungen - Bestimmung der
Schrumpfungstemperatur bis 100 °C (ISO/FDIS 3380:2015)
Cuir - Essais physiques et mécaniques - Détermination de la température de
rétrécissement jusqu'à 100 degrés C (ISO/FDIS 3380:2015)
Ta slovenski standard je istoveten z: FprEN ISO 3380 rev
ICS:
59.140.30 Usnje in krzno Leather and furs
kSIST FprEN ISO 3380:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 3380:2015
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 3380:2015
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 3380
IULTCS/IUP 16
IULTCS
Leather — Physical and mechanical
Voting begins
on: 201 5-05-07
tests - Determination of shrinkage
Voting terminates temperature up to 100 °C
on: 201 5-07-07
Cuir — Essais physiques et mécaniques - Détermination de la
température de rétrécissement jusqu’à 100 °C
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference numbers
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 3380:2015(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
IULTCS/IUP 16:2015(E)
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2015
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 3380:2015
ISO/FDIS 3380:2015(E)
IULTCS/IUP 16:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 3380:2015
ISO/FDIS 3380:2015(E)
IULTCS/IUP 16:2015(E)
ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the European Committee for Standardization (CEN), and processed
under the CEN-lead mode of collaboration as defined in the Vienna Agreement. The final draft was established
on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel two-
month approval vote in ISO and two month formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
© ISO 2015 – All rights reserved iii
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 3380:2015
ISO/FDIS 3380:2015(E)
IULTCS/IUP 16:2015(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Sampling and sample preparation . 2
6 Procedure. 3
7 Test report . 3
Annex A (informative) Sources of test apparatus . 4
iv © ISO 2015 – All rights reserved
---------------------- Page: 6 ----------------------
kSIST FprEN ISO 3380:2015
ISO/FDIS 3380:2015(E)
IULTCS/IUP 16:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to
further the advancement of leather science and technology. IULTCS has three Commissions, which are
responsible for establishing international methods for the sampling and testing of leather. ISO recognizes
IULTCS as an international standardizing body for the preparation of test methods for leather.
ISO 3380 was prepared by the Physical Test Commission of the International Union of Leather
Technologists and Chemists Societies (IUP Commission, IULTCS) in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, the secretariat of
which is held by UNI, in accordance with the Agreement on
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.