SIST EN 1218-3:2002
(Main)Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
This European Standard sets out the requirements and/or the measures to remove the hazards and limit the risks on hand fed tenoning machines with sliding table for cutting structural timbers, hereinafter referred to as "machines".
This European Standard does not apply to :
¾ machines where the tenon is produced by means of milling tools;
¾ machines designed for a tool spindle speed exceeding 6000 min-1;
¾ machines where the cuts are made on both ends of the workpiece during one cycle;
¾ combined machines used for tenoning (see EN 940 : 1997);
¾ the tenoning attachment on a vertical spindle moulding machine (see EN 848-1 : 1998).
This European Standard covers the hazards relevant to this machine as listed in clause 4.
For Computer Numerically Controlled (CNC) machines this European Standard does not cover hazards related to Electro-Magnetic Compatibility (EMC).
This European Standard is primarily directed to machines which are manufactured after the date of issue of this European Standard.
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 3: Abbundmaschinen mit von Hand bewegtem Schiebetisch
Diese Europäische Norm beschreibt die Anforderungen und/oder Maßnahmen für die Beseitigung von Gefähr-dun-gen und zur Begrenzung der Risiken an Abbundmaschinen mit Handvorschub des Schiebetisches - im Folgenden als ¿Maschinen" bezeichnet, die zum Schneiden von Massivholz bestimmt sind.
Diese Europäische Norm gilt nicht für:
¾ Maschinen, bei denen Schlitz/Zapfen mit Fräswerkzeugen hergestellt wird;
¾ Maschinen, bei denen die konstruktiv vorgesehene Drehzahl irgend einer Werkzeugspindel 6000 min-1 übersteigt;
¾ Maschinen, bei denen die Schnitte in einem Durchlauf an beiden Enden des Werkstücks durchgeführt werden;
¾ kombinierte Maschinen, die zum Zapfenschneiden/Schlitzen verwendet werden (siehe EN 940:1997);
¾ die Zapfenschneideinrichtung für Tischfräsmaschinen (siehe EN 848-1:1998).
Diese Europäische Norm behandelt die von der Maschine ausgehenden Gefährdungen, wie sie in Abschnitt 4 aufgelistet sind.
Diese Europäische Norm behandelt bei CNC-Maschinen nicht die Gefährdungen im Zusammenhang mit der elek-tromagnetischen Verträglichkeit (EMV).
Diese Europäische Norm gilt in erster Linie für Maschinen, die nach dem Ausgabedatum dieser Europäischen Norm hergestellt werden.
Sécurité des machines a bois - Tenonneuses - Partie 3: Machines a avance manuelle et a table roulante pour la coupe des éléments de charpente de toit en bois
La présente Norme européenne spécifie les prescriptions et/ou les mesures qui doivent être prises pour éliminer les phénomènes dangereux et limiter les risques sur les machines à avance manuelle et à table roulante pour la coupe des éléments de charpente de toit en bois, ci-après désignées par le terme "machines".
La présente Norme européenne ne s'applique pas :
¾ aux machines sur lesquelles le tenon est réalisé à l'aide d'outils à fraiser ;
¾ aux machines conçues pour une vitesse d'une broche porte-outil supérieure à 6 000 min-1 ;
¾ aux machines sur lesquelles les coupes sont effectuées aux deux extrémités de la pièce durant un seul cycle ;
¾ aux machines combinées utilisées pour le tenonnage (voir l'EN 940:1997) ;
¾ aux accessoires de tenonnage installés sur une toupie verticale (voir l'EN 848-1:1998).
La présente norme couvre les phénomènes dangereux applicables à ces machines dont une liste est donnée à l'article 4.
Pour les machines à commande numérique (CN), la présente norme européenne ne traite pas les phénomènes dangereux liés à la comptabilité électromagnétique (CEM).
La présente Norme européenne est applicable avant tout aux machines fabriquées après la date de publication de la présente Norme européenne.
Varnost lesnoobdelovalnih strojev - Stroji za izdelovanje čepov in utorov - 3. del: Stroji za razrez lesa z ročno podajalno mizo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2002
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
6WURML]DUD]UH]OHVD]URþQRSRGDMDOQRPL]R
Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning
machines with sliding table for cutting structural timbers
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 3: Abbundmaschinen mit von Hand bewegtem Schiebetisch
Sécurité des machines a bois - Tenonneuses - Partie 3: Machines a avance manuelle et
a table roulante pour la coupe des éléments de charpente de toit en bois
Ta slovenski standard je istoveten z: EN 1218-3:2001
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 1218-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2001
ICS 79.120.10
English version
Safety of woodworking machines - Tenoning machines - Part 3:
Hand fed tenoning machines with sliding table for cutting
structural timbers
Sécurité des machines à bois - Tenonneuses - Partie 3: Sicherheit von Holzbearbeitungsmaschinen -
Machines à avance manuelle et à table roulante pour la Zapfenschneid- und Schlitzmaschinen - Teil 3:
coupe des éléments de charpente de toit en bois Abbundmaschinen mit von Hand bewegtem Schiebetisch
This European Standard was approved by CEN on 30 September 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-3:2001 E
worldwide for CEN national Members.
Contents
Foreword.3
0 Introduction .4
1 Scope .4
2 Normative references .4
3 Terms and definitions.6
3.1 Terms .6
3.2 Definitions.6
4 List of hazards.9
5 Safety requirements and/or measures .11
5.1 Controls .11
5.2 Protection against mechanical hazards .14
5.3 Protection against non-mechanical hazards .23
6 Information for use .26
6.1 Warning devices.26
6.2 Marking .26
6.3 Instruction handbook .26
Annex A (normative) Transportable machine stability test .28
A.1 Tilting Test.28
A.2 Displacement test .28
Annex B (normative) Saw spindle dimensional tolerances .30
Annex C (normative) Riving knife lateral stability test.31
Annex D (normative) Operating conditions for noise emission measurement .32
D.1 General.32
D.2 Noise measurements.32
Annex E (informative) Safe working practice .37
E.1 General.37
E.2 Sawblades.37
E.3 Workpiece.38
E.4 Sliding table.38
E.5 Noise .38
E.6 Dust .38
Annex ZA (informative) Relationship of this document with EC Directives.39
Bibliography .40
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 142 "Woodworking machines -
Safety", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2002, and conflicting national standards shall be withdrawn at the latest by
April 2002.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative annex ZA, which is an integral part of this document.
Organisations contributing to the preparation of this European Standard include European Committee of
Woodworking Machinery Manufacturers Association "EUMABOIS".
The annexes A, B, C and D are normative and annexes E and ZA are informative.
This standard includes a Bibliography.
The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement the
relevant A and B Standards on the subject of general safety (see introduction of EN 292-1 : 1991 for a description
of A, B and C standards).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.
0 Introduction
This European Standard has been prepared to be a harmonised standard to provide one means of conforming to
the essential safety requirements of the Machinery Directive, and associated EFTA regulations. This European
Standard is a type "C“ standard as defined in EN 292-1 : 1991.
The extent to which hazards are covered is indicated in the scope of this European Standard.
The requirements of this European Standard concern designers, manufacturers, suppliers and importers of hand
fed tenoning machines with sliding table for cutting structural timbers.
This European Standard also includes information to be provided by the manufacturer to the user.
Common requirements for tooling are given in EN 847-1 : 1997.
1 Scope
This European Standard sets out the requirements and/or the measures to remove the hazards and limit the risks
on hand fed tenoning machines with sliding table for cutting structural timbers, hereinafter referred to as
"machines".
This European Standard does not apply to :
machines where the tenon is produced by means of milling tools;
-1
machines designed for a tool spindle speed exceeding 6000 min ;
machines where the cuts are made on both ends of the workpiece during one cycle;
combined machines used for tenoning (see EN 940 : 1997);
the tenoning attachment on a vertical spindle moulding machine (see EN 848-1 : 1998).
This European Standard covers the hazards relevant to this machine as listed in clause 4.
For Computer Numerically Controlled (CNC) machines this European Standard does not cover hazards related to
Electro-Magnetic Compatibility (EMC).
This European Standard is primarily directed to machines which are manufactured after the date of issue of this
European Standard.
2 Normative references
This European Standard incorporates by dated or undated reference provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 292-1 : 1991 Safety of machinery - Basic concepts, general principles for design - Part 1 :
Basic terminology and methodology.
EN 292-2 : 1991 Safety of machinery - Basic concepts, general principles for design - Part 2 :
EN 292-2/A1 : 1995 Technical principles and specifications.
EN 418 : 1992 Safety of machines - Emergency stop equipment - Functional aspects –
Principles for design.
EN 847-1 : 1997 Tools for woodworking - Safety requirements – Part 1 : Milling tools and circular
sawblades.
EN 954-1 : 1996 Safety of machinery - Safety related parts of control systems - Part 1 : General
principles for design.
EN 982 : 1996 Safety requirements for fluid power systems and components – Hydraulics.
EN 983 : 1996 Safety requirements for fluid power systems and components – Pneumatics.
EN 1088 : 1995 Safety of machinery - Interlocking devices associated with guards – Principles
for design and selection.
EN 60204-1 : 1992 Safety of machinery - Electrical equipment of machines - Part 1 : General
requirements (IEC 204-1 : 1992, modified).
EN 60529 : 1991 Degree of protection provided by enclosures (IP code) (IEC 60529 : 1989).
EN 60825-1 : 1994 Safety of laser products - Part 1 : Equipment classification, requirements and
users guide (IEC 60825-1 : 1993).
EN 60947-4-1 : 1992 Low voltage switchgear and control gear - Part 4 : Contactors and motor starters
- Section 1 : Electromechanical contactors and motor starters
(IEC 60947-4-1 : 1990).
EN 60947-5-1 : 1997 Low voltage switchgear and control gear - Part 5 : Control circuit devices and
switching elements – Section 1 : Electromechanical control circuit devices
(IEC 60947-5-1 : 1997).
EN ISO 3743-1 : 1995 Acoustics – Determination of sound power levels of noise sources - Engineering
methods for small, moveable sources in reverberant fields - Part 1 : Comparison
method for hard wall test rooms (ISO 3743-1 : 1994).
EN ISO 3743-2 : 1996 Acoustics - Determination of sound power levels of noise sources - Engineering
methods for small, moveable sources in reverberant fields - Part 2 : Method for
special reverberation test rooms (ISO 3743-2 : 1994).
EN ISO 3744 : 1995 Acoustics - Determination of sound power levels of noise sources using sound
pressure engineering methods in an essentially free field over a reflecting plane
(ISO 3744 : 1994).
EN ISO 3746 : 1995 Acoustics – Determination of sound power levels of noise sources using sound
pressure – Survey method employing an enveloping measurement surface over
a reflecting plane (ISO 3746 : 1995).
EN ISO 4871 : 1996 Acoustics – Determination and verification of noise emission values of
machinery and equipment (ISO 4871 : 1996).
EN ISO 9614-1 : 1995 Acoustics - Determination of sound power levels of noise sources using sound
intensity - Part 1 : Measurement at discrete points (ISO 9614-1 : 1993).
EN ISO 11202 : 1995 Acoustics -
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.