Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT). The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test temperature, determined during this standardized procedure, at which the tested material
a) does not ignite, or
b) if sustained and continuous flaming combustion does not occur for a time longer than 5 s for any single flame event and the specimen is not totally consumed. This test is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire flammability index (GWFI) test method for materials, IEC 60695-2-12, can then be used in a preselection process in accordance with IEC 60695-1-30 to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests may allow a reduction of end product testing. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Prüfungen zur Beurteilung der Brandgefahr - Teil 2-13: Prüfverfahren mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entzündbarkeit (GWIT) von Werkstoffen

Essais relatifs aux risques du feu - Partie 2-13: Essais au fil incandescent/chauffant - Méthode d'essai de température d'allumabilité au fil incandescent (GWIT) pour matériaux

IEC 60695-2-13:2014 Amendement 1

Preskušanje požarne ogroženosti - 2-13. del: Preskusne metode z žarilno žico - Preskusna metoda za materiale: temperatura vžiga žareče žice (GWIT) - Dopolnilo A1 (IEC 60695-2-13:2010/A1:2014)

Ta del IEC 60695 določa podrobnosti preskusa z žarilno žico, ki se uporablja za preskus vzorca trdnih električnih izolacijskih materialov ali trdnih materialov za preskušanje vnetljivosti, da se ugotovi temperatura vžiga žareče žice (GWIT). GWIT je temperatura, ki je za 25 K (ali 30 K) višja od maksimalne preskusne temperature, ugotovljena med tem standardiziranim postopkom, pri katerem se preskusni material:
a) ne vname ali
b) če se ne pojavi stalno in neprekinjeno zgorevanje s plamenom v času, ki presega 5 s za katero koli posamično gorenje, in se vzorec ne porabi v celoti. Ta preskus je preskus materialov, izveden na seriji standardnih preskusnih vzorcev. Pridobljeni podatki, skupaj s podatki preskusne metode indeksa vnetljivosti žarilne žice (GWFI) za materiale, IEC 60695-2-12, se lahko uporabijo v predizbirnem postopku v skladu z IEC 60695-1-30, da se presodi, ali materiali lahko izpolnjujejo zahteve iz IEC 60695-2-11. OPOMBA Kot posledica izvajanja ocene požarne ogroženosti primerno zaporedje predizbirnih preskusov vnetljivosti in vžiga lahko omogoči zmanjševanje preskušanja končnega proizvoda. Ta osnovna varnostna publikacija je namenjena temu, da jo uporabljajo tehnični odbori pri pripravi standardov v skladu z načeli, opredeljenimi v IEC Guide 104 in ISO/IEC Guide 51. Ena od odgovornosti tehničnega odbora je, če je to primerno, uporabiti temeljne varnostne publikacije pri pripravi svojih publikacij. Zahteve, preskusne metode ali preskusni pogoji te temeljne varnostne publikacije se ne uporabljajo, razen če se ustrezne publikacije nanje izrecno sklicujejo ali jih vključujejo.

General Information

Status
Published
Publication Date
03-Jul-2014
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Jun-2014
Due Date
21-Aug-2014
Completion Date
04-Jul-2014

RELATIONS

Buy Standard

Amendment
SIST EN 60695-2-13:2011/A1:2014
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 60695-2-13:2011/A1:2014
01-september-2014
3UHVNXãDQMHSRåDUQHRJURåHQRVWLGHO3UHVNXVQHPHWRGH]åDULOQRåLFR
3UHVNXVQDPHWRGD]DPDWHULDOHWHPSHUDWXUDYåLJDåDUHþHåLFH *:,7 'RSROQLOR
$ ,(&$

Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition

temperature (GWIT) test method for materials

Prüfungen zur Beurteilung der Brandgefahr - Teil 2-13: Prüfverfahren mit dem Glühdraht

- Prüfung mit dem Glühdraht zur Entzündbarkeit (GWIT) von Werkstoffen

Essais relatifs aux risques du feu - Partie 2-13: Essais au fil incandescent/chauffant -

Méthode d'essai de température d'allumabilité au fil incandescent (GWIT) pour matériaux

Ta slovenski standard je istoveten z: EN 60695-2-13:2010/A1:2014
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
SIST EN 60695-2-13:2011/A1:2014 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60695-2-13:2011/A1:2014
---------------------- Page: 2 ----------------------
SIST EN 60695-2-13:2011/A1:2014
EUROPEAN STANDARD EN 60695-2-13:2010/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 13.220.40; 29.020
English Version
Fire hazard testing - Part 2-13: Glowing/hot-wire based test
methods - Glow-wire ignition temperature (GWIT) test method
for materials
(IEC 60695-2-13:2010/A1:2014)

Essais relatifs aux risques du feu - Partie 2-13: Essais au fil Prüfungen zur Beurteilung der Brandgefahr - Teil 2-13:

incandescent/chauffant - Méthode d'essai de température Prüfverfahren mit dem Glühdraht - Prüfung mit dem

d'allumabilité au fil incandescent (GWIT) pour matériaux Glühdraht zur Entzündbarkeit (GWIT) von Werkstoffen

(CEI 60695-2-13:2010/A1:2014) (IEC 60695-2-13:2010/A1:2014)

This amendment A1 modifies the European Standard EN 60695-2-13:2010; it was approved by CENELEC on 2014-03-19. CENELEC

members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the

status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the

responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 60695-2-13:2010/A1:2014 E
---------------------- Page: 3 ----------------------
SIST EN 60695-2-13:2011/A1:2014
---------------------- Page: 4 ----------------------
SIST EN 60695-2-13:2011/A1:2014
EN 60695-2-13:2010 /A1:2014 - 2 -
Foreword

The text of document 89/1199/FDIS, future IEC 60695-2-13:2010/A1, prepared by IEC TC 89, Fire hazard

testing, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60695-

2-13:2010/A1:2014.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent

rights.
The following dates were fixed:
– latest date by which the EN has to be implemented (dop) 2014-12-19
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2017-03-19
with the EN have to be withdrawn
Endorsement notice

The text of the International Standard IEC 60695-2-13:2010/A1:2014 was approved by CENELEC as a

European Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60695-2-11 NOTE Harmonized as EN 60695-2-11.
ISO/IEC 13943:2008 NOTE Harmonized as EN ISO 13943:2010.
---------------------- Page: 5 ----------------------
SIST EN 60695-2-13:2011/A1:2014
- 3 - EN 60695-2-13:2010/A1:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
Publication Year Title EN/HD Year

In Annex ZA of EN 60695-2-13:2010, remove the dates from the following existing references:

IEC Guide 104 - The preparation of safety publications and - -
the use of basic safety publications and
group safety publications
ISO 293 - Plastics - Compression moulding of test EN ISO 293 -
specimens of thermoplastic materials
ISO 295 - Plastics_- Compression moulding of test EN ISO 295 -
specimens of thermosetting materials
ISO/IEC Guide 51 - Safety aspects - Guidelines for their - -
inclusion in standards
In Annex ZA of EN 60695-2-13:2010, remove the following references:
IEC 60695-2-11 2000 Fire hazard testing - EN 60695-2-11 2001
Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test
method for end-products
ISO 13943 2008 Fire safety - Vocabulary EN ISO 13943 2010
---------------------- Page: 6 ----------------------
SIST EN 60695-2-13:2011/A1:2014
IEC 60695-2-13
Edition 2.0 2014-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
BA SIC SAFETY PUBLICATION
PU BLICATION FONDAMENTALE DE SÉCURITÉ
AMENDMENT 1
AMENDEMENT 1
Fire hazard testing –
Part 2-13: Glowing/hot-wire based test methods – Glow-wire ignition
temperature (GWIT) test method for materials
Essais relatifs aux risques du feu –
Partie 2-13: Essais au fil incandescent/chauffant – Méthode d’essai de
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.