SIST EN ISO 294-3:2003
(Main)Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002)
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002)
This part of ISO 294 specifies two two-cavity moulds, the type D1 and D2 ISO moulds, for the injection moulding of small plates measuring 60 mm × 60 mm with a preferred thickness of 1 mm (type D1) or 2 mm (type D2), which can be used for a variety of tests. The moulds may additionally be fitted with inserts for studying the effects of weld lines on the mechanical properties.
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 3: Kleine Platten (ISO 294-3:2002)
Dieser Teil von ISO 294 legt zwei Zweifachwerkzeuge fest, die ISO-Typ-D1- und D2-Werkzeuge zum Spritzgießen kleiner Platten 60 mm × 60 mm mit den Vorzugsdicken von 1 mm (Typ D1) und 2 mm (Typ D2), die für eine Vielzahl von Prüfungen benutzt werden können. Die Werkzeuge können zusätzlich mit Einsätzen versehen werden zur Untersuchung der Wirkung von Fließnähten auf mechanische Eigenschaften (siehe Anhang A).
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques - Partie 3: Plaques de petites dimensions (ISO 294-3:2002)
La présente partie de l'ISO 294 spécifie deux moules à deux empreintes de type moules ISO D1 et D2 pour le moulage par injection de petites plaques de 60 mm × 60 mm présentant une épaisseur préférentielle de 1 mm (type D1) ou 2 mm (type D2), qui peuvent être utilisés pour de multiples essais. Les moules peuvent, en outre, être équipés d'inserts en vue de l'étude de l'effet induit par les lignes de soudure sur les propriétés mécaniques.
Polimerni materiali - Vbrizgavanje plastomernih preskušancev - 3. del: Ploščice (ISO 294-3:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 294-3:2003
01-december-2003
1DGRPHãþD
SIST EN ISO 294-3:2000
3ROLPHUQLPDWHULDOL9EUL]JDYDQMHSODVWRPHUQLKSUHVNXãDQFHYGHO 3ORãþLFH
,62
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small
plates (ISO 294-3:2002)
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 3: Kleine Platten
(ISO 294-3:2002)
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques -
Partie 3: Plaques de petites dimensions (ISO 294-3:2002)
Ta slovenski standard je istoveten z: EN ISO 294-3:2003
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 294-3:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 294-3:2003
---------------------- Page: 2 ----------------------
SIST EN ISO 294-3:2003
EUROPEAN STANDARD
EN ISO 294-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2003
ICS 83.080.20 Supersedes EN ISO 294-3:1998
English version
Plastics - Injection moulding of test specimens of thermoplastic
materials - Part 3: Small plates (ISO 294-3:2002)
Plastiques - Moulage par injection des éprouvettes de Kunststoffe - Spritzgießen von Probekörpern aus
matériaux thermoplastiques - Partie 3: Plaques de petites Thermoplasten - Teil 3: Kleine Platten (ISO 294-3:2002)
dimensions (ISO 294-3:2002)
This European Standard was approved by CEN on 26 June 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 294-3:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 294-3:2003
EN ISO 294-3:2003 (E)
Foreword
The text of ISO 294-3:2002 has been prepared by Technical Committee ISO/TC 6 "Plastics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO
294-3:2003 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by
IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2004, and conflicting national
standards shall be withdrawn at the latest by January 2004.
This document supersedes EN ISO 294-3:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 294-3:2002 has been approved by CEN as EN ISO 294-3:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 294-3:2003
EN ISO 294-3:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 294-1 1996 Plastics - Injection moulding of test EN ISO 294-1 1998
specimens of thermoplastic materials
- Part 1: General principles, and
moulding of multipurpose and bar test
specimens
ISO 294-4 1997 Plastics - Injection moulding of test EN ISO 294-4 1998
specimens of thermoplastic materials
- Part 4: Determination of moulding
shrinkage
ISO 6603-1 2000 Plastics - Determination of puncture EN ISO 6603-1 2000
impact behaviour of rigid plastics -
Part 1: Non-instrumented impact
testing
ISO 6603-2 2000 Plastics - Determination of puncture EN ISO 6603-2 2000
impact behaviour of rigid plastics -
Part 2: Instrumented puncture test
3
---------------------- Page: 5 ----------------------
SIST EN ISO 294-3:2003
---------------------- Page: 6 ----------------------
SIST EN ISO 294-3:2003
INTERNATIONAL ISO
STANDARD 294-3
Second edition
2002-06-01
Plastics — Injection moulding of test
specimens of thermoplastic materials —
Part 3:
Small plates
Plastiques — Moulage par injection des éprouvettes de matériaux
thermoplastiques —
Partie 3: Plaques de petites dimensions
Reference number
ISO 294-3:2002(E)
©
ISO 2002
---------------------- Page: 7 ----------------------
SIST EN ISO 294-3:2003
ISO 294-3:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 294-3:2003
ISO 294-3:2002(E)
Contents Page
Foreword.iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Apparatus.2
5 Procedure.4
6 Report on test-specimen preparation.5
Annex A (informative) Weld lines .6
Bibliography.8
© ISO 2002 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 294-3:2003
ISO 294-3:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 294 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 294-3 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This second edition cancels and replaces the first edition (ISO 294-3:1996), which has been technically revised.
ISO 294 consists of the following parts, under the general title Plastics — Injection moulding of test specimens of
thermoplastic materials:
Part 1: General principles, and moulding of multipurpose and bar test specimens
Part 2: Small tensile bars
Part 3: Small plate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.