SIST EN ISO 25137-1:2017

Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 25137-1:2009)

ISO 25137-1:2009 establishes a system of designation for sulfone polymer moulding and extrusion materials, including polysulfone (PSU), polyethersulfone (PESU) and polyphenylsulfone (PPSU), which may be used as the basis for specifications.
The types of sulfone plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties
temperature of deflection under load,
melt mass-flow rate,
Charpy notched impact strength,
tensile modulus and
yield stress,
and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.
This part of ISO 25137 is applicable to all sulfone polymers that contain ether oxygen, which is a necessary component of the polymers as in the diphenyl sulfone moiety.
It applies to sulfone polymer materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, additives, fillers, etc.

Kunststoffe - Sulfonpolymer-Werkstoffe - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 25137-1:2009)

1.1   Der vorliegende Teil von ISO 25137 legt ein System für die Bezeichnung von Sulfonpolymer-Werkstoffen für das Spritzgießen und die Extrusion fest, einschließlich Polysulfon (PSU), Polyethersulfon (PESU) und Polyphenylsulfon (PPSU), das als Grundlage für Spezifikationen angewendet werden kann.
1.2   Die Typen der Sulfonpolymer-Werkstoffe werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften
a)   Wärmeformbeständigkeitstemperatur,
b)   Schmelze-Massefließrate,
c)   Charpy-Kerbschlagzähigkeit,
d)   Zugmodul und
e)   Streckspannung,
und auf Informationen über die Zusammensetzung, vorgesehene Anwendung und/oder Verarbeitungs-verfahren, wichtige Eigenschaften, Additive (Zusatzstoffe), Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3   Dieser Teil von ISO 25137 gilt für alle Sulfonpolymere, die Ethersauerstoff enthalten, welcher ein wichtiger Bestandteil der Polymere ist, wie der Diphenylsulfon-Rest.
Er gilt für gebrauchsfertige Sulfonpolymer-Werkstoffe in Form von Pulver, Granulaten oder Pellets, die unmodifiziert oder mit Farbstoffen, Zusatzstoffen, Füllstoffen usw. modifiziert sind.
1.4   Es soll nicht unterstellt werden, dass Werkstoffe mit gleicher Bezeichnung notwendigerweise das Gleiche leisten. Dieser Teil von ISO 25137 enthält keine technischen Daten, Leistungsangaben oder Angaben zu Verarbeitungsbedingungen, die erforderlich sein können, um einen Werkstoff für eine bestimmte Anwendung und/oder Verarbeitungsart zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften erforderlich sind, müssen sie nach den in Teil 2 dieser Internationalen Norm festgelegten Prüfverfahren, soweit geeignet, bestimmt werden.
1.5   Um einen thermoplastischen Werkstoff für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen im Datenblock 5 (siehe 3.1) zusätzliche Anforderungen angegeben werden.

Plastiques - Matériaux pour moulage et extrusion à base de polymères sulfone - Partie 1: Système de désignation et base de spécifications (ISO 25137-1:2009)

L'ISO 25137-1:2009 établit un système de désignation des matériaux pour moulage et extrusion à base de polymères sulfone, y compris le polysulfone (PSU), le polyéthersulfone (PESU) et le polyphénylsulfone (PPSU), qui peut être utilisé comme base pour les spécifications.
Les types de matériaux à base de polymères sulfone sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation:
a) température de fléchissement sous charge,
b) indice de fluidité à chaud en masse,
c) résistance au choc Charpy avec entaille,
d) module en traction, et
e) contrainte au seuil d'écoulement,
et des informations concernant la composition, l'application prévue et/ou la méthode de mise en oeuvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
L'ISO 25137-1:2009 s'applique à tous les polymères sulfone qui contiennent de l'éther-oxyde, qui est un composant nécessaire des polymères comme dans le groupe fonctionnel diphénylsulfone.
Elle s'applique aux matériaux à base de polymères sulfone prêts à l'emploi normal sous forme de poudre, de grains ou de granulés, non modifiés ou modifiés par des colorants, des additifs, des charges, etc.
Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. L'ISO 25137-1:2009 ne comporte pas de données sur la conception, la performance ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en oeuvre particulière.
Si de telles caractéristiques supplémentaires sont nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans la Partie 2 de cette Norme internationale, s'il y a lieu.
Afin de spécifier un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en oeuvre reproductible, des exigences supplémentaires peuvent être codées dans le bloc de données 5.

Polimerni materiali - Sulfonski polimerni materiali za brizganje in ekstrudiranje - 1. del: Sistem označevanja in podlage za specifikacije (ISO 25137-1:2009)

Standard ISO 25137-1:2009 določa sistem označevanja za sulfonske polimerne materiale za brizganje in ekstrudiranje, vključno s polisulfonom (PSU), polietersulfonom (PESU) in polifenilsulfonom (PPSU), ki se lahko uporabljajo kot podlaga za specifikacije.
Vrste sulfonskih polimernih materialov se med seboj ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh označevalnih lastnosti
temperature upogiba pod obremenitvijo,
prostorninskega pretoka taline,
zarezne udarne žilavosti po Charpyju,
nateznega modula in
obremenitve meje prožnosti
ter informacijah o sestavi, predvideni uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih in materialih za ojačanje.
Ta del standarda ISO 25137 se uporablja za vse sulfonske polimere, ki vsebujejo eter-kisik, ki je nujna komponenta polimerov, npr. skupina difenil sulfona.
Uporablja se za sulfonske polimerne materiale v obliki praška, granul ali peletov, pripravljene za običajno uporabo, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 13-Oct-2016
• Publication Date: 01-Feb-2017
• Withdrawal Date: 03-Jun-2020
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 04-Jun-2020
• Due Date: 27-Jun-2020
• Completion Date: 04-Jun-2020
• Ref Project: EN ISO 25137-1:2017 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 25137-1:2009)

Relations

• Replaced By: SIST EN ISO 24025-1:2020 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24025-1:2020)
• Effective Date: 03-Jun-2020
• Revised: SIST EN ISO 24025-1:2020 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24025-1:2020)
• Effective Date: 16-Jan-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 25137-1:2017
01-marec-2017
3ROLPHUQLPDWHULDOL6XOIRQVNLSROLPHUQLPDWHULDOL]DEUL]JDQMHLQHNVWUXGLUDQMH
GHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH,62
Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system
and basis for specifications (ISO 25137-1:2009)
Kunststoffe - Sulfonpolymer-Werkstoffe - Teil 1: Bezeichnungssystem und Basis für
Spezifikationen (ISO 25137-1:2009)
Plastiques - Matériaux pour moulage et extrusion à base de polymères sulfone - Partie 1:
Système de désignation et base de spécifications (ISO 25137-1:2009)
Ta slovenski standard je istoveten z: EN ISO 25137-1:2017
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 25137-1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 25137-1:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 25137-1:2017


EN ISO 25137-1
EUROPEAN STANDARD

NORME EUROPÉENNE

January 2017
EUROPÄISCHE NORM
ICS 83.080.20
English Version

Plastics - Sulfone polymer moulding and extrusion
materials - Part 1: Designation system and basis for
specifications (ISO 25137-1:2009)
Plastiques - Matériaux pour moulage et extrusion à Kunststoffe - Sulfonpolymer-Werkstoffe - Teil 1:
base de polymères sulfone - Partie 1: Système de Bezeichnungssystem und Basis für Spezifikationen
désignation et base de spécifications (ISO 25137- (ISO 25137-1:2009)
1:2009)
This European Standard was approved by CEN on 20 December 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25137-1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 25137-1:2017
EN ISO 25137-1:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 25137-1:2017
EN ISO 25137-1:2017 (E)
European foreword
The text of ISO 25137-1:2009 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 25137-1:2017
by Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be
withdrawn at the latest by July 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 25137-1:2009 has been approved by CEN as EN ISO 25137-1:2017 without any
modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 25137-1:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 25137-1:2017

INTERNATIONAL ISO
STANDARD 25137-1
First edition
2009-01-15

Plastics — Sulfone polymer moulding
and extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux pour moulage et extrusion à base de
polymères sulfone —
Partie 1: Système de désignation et base de spécifications




Reference number
ISO 25137-1:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 25137-1:2017
ISO 25137-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 25137-1:2017
ISO 25137-1:2009(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 2
3 Designation system. 2
3.1 General. 2
3.2 Data block 1. 2
3.3 Data block 2. 3
3.4 Data block 3. 4
3.5 Data block 4. 7
3.6 Data block 5. 7
4 Examples of designations . 8
4.1 Designation only. 8
4.2 Designation transformed into a specification . 10
Bibliography . 11

© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 25137-1:2017
ISO 25137-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 25137-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
ISO 25137 consists of the following parts, under the general title Plastics — Sulfone polymer moulding and
extrusion materials:
⎯ Part 1: Designation system and basis for specifications
⎯ Part 2: Preparation of test specimens and determination of properties

iv © ISO 2009 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 25137-1:2017
INTERNATIONAL STANDARD ISO 25137-1:2009(E)

Plastics — Sulfone polymer moulding and extrusion
materials —
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of ISO 25137 establishes a system of designation for sulfone polymer moulding and extrusion
materials, including polysulfone (PSU), polyethersulfone (PESU) and polyphenylsulfone (PPSU), which may
be used as the basis for specifications.
1.2 The types of sulfone polymer materials are differentiated from each other by a classification system
based on appropriate levels of the designatory properties
a) temperature of deflection under load,
b) melt mass-flow rate,
c) Charpy notched impact strength,
d) tensile modulus and
e) yield stress,
and on information about composition, intended application and/or method of processing, important properties,
additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 25137 is applicable to all sulfone polymers that contain ether oxygen, which is a
necessary component of the polymers as in the diphenyl sulfone moiety.
It applies to sulfone polymer materials ready for normal use in the form of powder, granules or pellets,
unmodified or modified by colorants, additives, fillers, etc.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 25137 does not provide engineering data, performance data or data on
processing conditions which may be required to specify a material for a particular application and/or method of
processing.
If such additional properties are required, they shall be determined in accordance with the test methods
specified in Part 2 of this International Standard, if suitable.
1.5 In order to specify a thermoplastic material for a
...