SIST EN 60745-2-4:2010

Hand-held motor-operated electric tools - Safety -- Part 2-4: Particular requirements for sanders and polishers other than disk type

This clause of Part 1 is applicable, except as follows: Addition: This standard applies to sanders and polishers with the exception of all types of disc-type tools, which are covered by IEC 60745-2-3. Tools covered by this standard include but are not limited to belt sanders, reciprocating sanders or polishers, orbital sanders or polishers, and random orbit sanders or polishers.

Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit -- Teil 2-4: Besondere Anforderungen für Schleifer und Polierer außer Tellerschleifern

Outils électroportatifs à moteur - Sécurité -- Partie 2-4: Règles particulières pour les ponceuses et lustreuses, autres que du type à disque

Električna ročna orodja - Varnost - 2-4. del: Posebne zahteve za brusilnike in polirnike, razen diskovnih brusilnikov (IEC 60745-2-4:2002, spremenjen + A1:2008, spremenjen)

Uporablja se ta klavzula prvega dela, razen kot sledi: Dodatek: Ta standard velja za peskalnike in brusilnike z izjemo vseh vrst kolutnih orodij, ki so zajeta v IEC 60745-2-3. Orodja, zajeta v tem standardu, vsebujejo, vendar niso omejena na tračne brusilnike, recipročne peskalnike in brusilnike, vibracijske peskalnike in brusilnike ter izsredne peskalnike in brusilnike.

General Information

• Status: Withdrawn
• Publication Date: 14-Mar-2010
• Withdrawal Date: 19-Apr-2023
• ICS: 25.080.50 - Grinding and polishing machines
• ICS: 25.140.20 - Electric tools
• Technical Committee: VGA - Safety of household and similar electrical appliances
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 20-Apr-2023
• Due Date: 13-May-2023
• Completion Date: 20-Apr-2023
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 60745-2-4:2009 - Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type

Relations

• Revised: SIST EN 62841-2-4:2014 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type
• Effective Date: 06-May-2014
• Replaced By: SIST EN 62841-2-4:2014 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type
• Effective Date: 07-Jun-2022
• Amended By: SIST EN 60745-2-4:2010/A11:2012 - Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 07-Jun-2022
• Amended By: SIST EN 60745-2-4:2010/oprAB:2013 - Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 07-Jun-2022
• Replaces: SIST EN 60745-2-4:2003 - Hand-held motor-operated electric tools - Safety -- Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 01-Apr-2010
• Replaces: SIST EN 60745-2-4:2003/A11:2007 - Hand-held motor-operated electric tools - Safety -- Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 01-Apr-2010
• Replaces: SIST EN 60745-2-4:2003/A1:2009 - Hand-held motor-operated electric tools - Safety -- Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 01-Apr-2010
• Amended By: SIST EN 60745-2-4:2010/A11:2012 - Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 01-Mar-2011
• Replaced By: SIST EN 62841-2-4:2014 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type
• Effective Date: 08-Oct-2012
• Amended By: SIST EN 60745-2-4:2010/oprAB:2013 - Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 04-Oct-2011
• Replaces: SIST EN 60745-2-4:2003/A1:2009 - Hand-held motor-operated electric tools - Safety -- Part 2-4: Particular requirements for sanders and polishers other than disk type
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60745-2-4:2010
01-april-2010
1DGRPHãþD
SIST EN 60745-2-4:2003
SIST EN 60745-2-4:2003/A1:2009
SIST EN 60745-2-4:2003/A11:2007
(OHNWULþQDURþQDRURGMD9DUQRVWGHO3RVHEQH]DKWHYH]DEUXVLOQLNHLQ
SROLUQLNHUD]HQGLVNRYQLKEUXVLOQLNRY,(&VSUHPHQMHQ$
VSUHPHQMHQ
Hand-held motor-operated electric tools - Safety -- Part 2-4: Particular requirements for
sanders and polishers other than disk type
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit -- Teil 2-4: Besondere
Anforderungen für Schleifer und Polierer außer Tellerschleifern
Outils électroportatifs à moteur - Sécurité -- Partie 2-4: Règles particulières pour les
ponceuses et lustreuses, autres que du type à disque
Ta slovenski standard je istoveten z: EN 60745-2-4:2009
ICS:
25.080.50 Brusilni in polirni stroji Grinding and polishing
machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 60745-2-4:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60745-2-4:2010

---------------------- Page: 2 ----------------------

SIST EN 60745-2-4:2010

EUROPEAN STANDARD
EN 60745-2-4

NORME EUROPÉENNE
December 2009
EUROPÄISCHE NORM

ICS 25.140.20; 25.140.30; 25.080.50 Supersedes EN 60745-2-4:2003 + A1:2009 + A11:2007


English version

Hand-held motor-operated electric tools -
Safety -
Part 2-4: Particular requirements for sanders and polishers
other than disk type
(IEC 60745-2-4:2002 + A1:2008, modified)


Outils électroportatifs à moteur -  Handgeführte motorbetriebene
Sécurité - Elektrowerkzeuge -
Partie 2-4: Règles particulières Sicherheit -
pour les ponceuses et les lustreuses Teil 2-4: Besondere Anforderungen
autres que du type à disque für Schleifer und Polierer
(CEI 60745-2-4:2002 außer Tellerschleifern
+ A1:2008, modifiés) (IEC 60745-2-4:2002,
+ A1:2008, modifiziert)


This European Standard was approved by CENELEC on 2009-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-4:2009 E

---------------------- Page: 3 ----------------------

SIST EN 60745-2-4:2010
EN 60745-2-4:2009 – 2 –
Foreword
The text of the International Standard IEC 60745-2-4:2002, prepared by SC 61F (transformed into
IEC TC 116, Safety of hand-held motor-operated electric tools), together with the common modifications
prepared by the Technical Committee CENELEC TC 61F (transformed into TC 116), was submitted to the
formal vote and was approved by CENELEC as EN 60745-2-4 on 2003-02-01.
A draft amendment (prAB) was prepared to align Subclause 6.2 with the new Subclause 6.2 in
EN 60745-1. Moreover, vibration values determined with the new 6.2 are complying with the requirements
of the Physical Agents Directive Vibration 2002/44/EC. The text of the draft was submitted to the Unique
Acceptance Procedure and was approved by CENELEC as amendment A11 to EN 60745-2-4:2003 on
2007-02-01.
The text of document 61F/733/FDIS, future amendment 1 to IEC 60745-2-4:2002, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60745-2-4:2003
on 2009-04-22.
A further draft amendment (prAC), extending Annex ZZ to include the new MD 2006/42/EC, was
submitted to the formal vote.
The combined texts were approved by CENELEC as a new edition of EN 60745-2-4 on 2009-09-01.
This European Standard supersedes EN 60745-2-4:2003 + A11:2007 + A1:2009.
The following dates were fixed:
- latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-02-01
- latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-05-01
This standard is divided into two parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of this
standard;
Part 2: Requirements for particular types of tools which either supplement or modify the requirements
given in Part 1 to account for the particular hazards and characteristics of these specific tools.
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and supports the essential requirements of
EC Directive 98/37/EC (Machinery Directive), amended by EC Directive 98/79/EC, and of EC Directive
2006/42/EC. See Annexes ZZA and ZZB.
Compliance with the clauses of Part 1 together with this Part 2 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
CEN/TC 255 is producing standards for non-electric sanders and polishers (EN 792-8).
Warning: Other requirements and other EC Directives can be applicable to the products falling within the
scope of this standard.
This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2.

---------------------- Page: 4 ----------------------

SIST EN 60745-2-4:2010
– 3 – EN 60745-2-4:2009
This Part 2-4 is to be used in conjunction with EN 60745-1:2009. When this standard states "addition",
"modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.
Subclauses and figures which are additional to those in Part 1 are numbered starting from 101.
Subclauses, tables and figures which are additional to those in IEC 60745-2-4 are prefixed “Z”.
NOTE In this standard, the following print types are used:
- requirements: in roman type;
- test specifications: in italic type;
- notes: in smaller roman type.

---------------------- Page: 5 ----------------------

SIST EN 60745-2-4:2010
EN 60745-2-4:2009 – 4 –
Endorsement notice
The text of the International Standard IEC 60745-2-4:2002 + A1:2008 was approved by CENELEC as a
European Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
1 Scope
Replace the first paragraph of the addition by:
This standard applies to sanders and polishers with the exception of all types of rotating disc-type
sanders, which are covered by EN 60745-2-3.
3 Terms and definitions
Add the following new definition:
3.Z101
mass of the tool
mass of the complete tool as prepared for the test with all equipment needed for normal use, but without
the cable
6 Void
Replace by:
6 Environmental requirements
This clause of Part 1 is applicable except as follows:
6.1.2.4 Modification:
Sanders and polishers are suspended. The plate of the tool shall be horizontal.
6.1.2.5 Modification:
Sanders and polishers are tested at no-load.
6.2 Vibration
6.2.4.2 Location of the measurement
Addition:
Figures Z101 and Z102 show the positions for different sanders and polishers.

---------------------- Page: 6 ----------------------

SIST EN 60745-2-4:2010
– 5 – EN 60745-2-4:2009
6.2.6.3 Operating conditions
Modification:
Sanders and polishers are tested under load observing the conditions shown in Tables Z101 and Z102.
Table Z101 - Operating conditions for sanders
Orientation
Sanding a horizontal steel plate 400 mm × 400 mm × 20 mm mounted on a
bench
Tool bit Recommended sanding paper for steel with a grain size of 180
Feed force 30 N ± 5 N, if the mass of the tool is less than 1,5 kg
50 N ± 5 N, if the mass of the tool is equal or greater than 1,5 kg
Pre-test requirements With a new sanding sheet carry out 1 min sanding before starting measurements

Table Z102 - Operating conditions for polishers
Orientation
Polishing a horizontal steel plate 400 mm × 400 mm × 20 mm mounted on a
bench
Tool bit Polishing pad
Feed force 30 N ± 5 N, if the mass of the tool is less than 1,5 kg
50 N ± 5 N, if the mass of the tool is equal or greater than 1,5 kg

6.2.7.2 Declaration of the vibration total value
Addition:
The vibration total value a of the handle with the highest emission and the uncertainty K shall be
h
declared.
8 Marking and instructions
Add:
8.12.2 Za) Addition:
101) for sanders:
instructions how to deal with harmful/toxic dusts arising from sanding e.g. lead painted surfaces,
woods and metals. These instructions shall be proceeded by a warning that contact with or inhalation
of these dusts can endanger the health of operator and bystanders. These instructions shall include
the use of appropriate personal protective equipment.

---------------------- Page: 7 ----------------------

SIST EN 60745-2-4:2010
EN 60745-2-4:2009 – 6 –
21 Construction
Replace by:
This clause of Part 1 is applicable except as follows:
21.Z1 Addition:
Sanders for woodworking are considered to be tools where a considerable amount of dust is produced.

---------------------- Page: 8 ----------------------

SIST EN 60745-2-4:2010
– 7 – EN 60745-2-4:2009
Add the following new figures:



Figure Z101 - Position of transducers for sanders and polishers

---------------------- Page: 9 ----------------------

SIST EN 60745-2-4:2010
EN 60745-2-4:2009 – 8 –
Bibliography
Replace the addition by:
EN 60745-2-3:2007, Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements
for grinders, polishers and disk-type sanders (IEC 60745-2-3:2006, mod)

---------------------- Page: 10 ----------------------

SIST EN 60745-2-4:2010
– 9 – EN 60745-2-4:2009
Add the following annex:
Annex ZZ
(informative)
Annex ZZA
(informative)

Coverage of Essential Requirements of Directive 98/37/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 98/37/EC (Machinery Directive), amended by
Directive 98/79/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
Annex ZZB
(informative)

Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.

---------------------- Page: 11 ----------------------

SIST EN 60745-2-4:2010

---------------------- Page: 12 ----------------------

SIST EN 60745-2-4:2010
IEC 60745-2-4
Edition 2.1 2008-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Hand-held motor-operated electric tools – Safety –
Part 2-4: Particular requirements for sanders and polishers other than disk type

Outils électroportatifs à moteur – Sécurité –
Partie 2-4: Règles particulières pour les ponceuses et les lustreuses autres que
du type à disque

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CB
CODE PRIX
ICS 25.140.20; 24.140.30; 25.080.50 ISBN 2-8318-9909-5
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 13 ----------------------

SIST EN 60745-2-4:2010
– 2 – 60745-2-4 © IEC:2002+A1:2008
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________

HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS –
SAFETY –

Part 2-4: Particular requirements for sanders and polishers
other than disk type



FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standard
...