iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12636:2000

(Main)

Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to concrete

Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to concrete

This European Standard describes methods for the measurement of the adhesion of structural bonding agents between fresh or hardened concrete and a hardened concrete substrate

Produkte für den Schutz und die Instandsetzung von Betontragwerken - Prüfverfahren - Bestimmung der Verbundwirkung Beton-Beton

Die Europäische Norm beschreibt Verfahren für die Messung der Verbundwirkung von Bauhaftmitteln zwischen Frisch- oder Festbeton und einem Festbetonuntergrund

Produits et systemes pour la protection et la réparation des structures en béton - Méthodes d'essais - Détermination de l'adhérence béton sur béton

La présente norme européenne décrit des méthodes permettant de mesurer l'adhérence des agents adhésifs structurels utilisés entre un béton frais ou durci et un subfectile en béton durci.

Proizvodi in sistemi za zaščito in popravilo betonskih konstrukcij - Preskusne metode - Določevanje sprijetosti betona na beton

General Information

Status
Published
Publication Date
30-Apr-2000
ICS
91.080.40 - Concrete structures
Technical Committee
BBB - Concrete, reinforced concrete and prestressed concrete
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-May-2000
Due Date
01-May-2000
Completion Date
01-May-2000
Directive
89/106/EEC - Construction products
Mandate
M/128 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on products for concrete, mortar and grout
Ref Project
EN 12636:1999 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to concrete

Buy Standard

EN 12636:2000EN 12636:2000
PreviousNext
Standard
EN 12636:2000
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Produkte für den Schutz und die Instandsetzung von Betontragwerken - Prüfverfahren - Bestimmung der Verbundwirkung Beton-BetonProduits et systemes pour la protection et la réparation des structures en béton - Méthodes d'essais - Détermination de l'adhérence béton sur bétonProducts and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 17678-1:2023(Main)
Installation of post-tensioning kits for prestressing of structures - Part 1: Competence of personnel
EN 17678-1:2022

This document indicates the minimum training and registration requirements for post-tensioning personnel involved in the installation of PT kits in concrete structures using bonded or unbonded tendons in accordance with the relevant execution specifications, product standard and/or European Technical Assessment (ETA).
This document describes the tasks that the various categories of PT personnel can undertake.
For the purposes of this document, PT personnel means: PT-Manager, Supervisors, Operatives and Trainees who are directly employed or indirectly employed on a sub-contract basis.
This document does not cover general safety and health aspects.
This document does not cover contractual issues.
prEN 17678-2 deals with the assessment of competence.
Note: It is within the concept of this document that supplementing requirements can be given in the execution specification or in a national annex.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17086:2020(Main)
Further guidance on the application of EN 13791:2019 and background to the provisions
CEN/TR 17086:2020

This Technical Report explains the reasoning behind the requirements and procedures given in EN 13791 [1] and why some concepts and procedures given in EN 13791:2007 [2] were not adopted in the 2017 revision. The annex comprises worked examples of the procedures given in EN 13791.

  • Technical report
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13791:2019(Main)
Assessment of in-situ compressive strength in structures and precast concrete components
EN 13791:2019

(1)   This European Standard:
-   gives methods and procedures for the estimation of the in-situ compressive strength and characteristic in-situ compressive strength of concrete in structures and precast concrete components using direct methods (core testing) and indirect methods, e.g. ultra-sonic pulse velocity, rebound number;
-   provides principles and guidance for establishing the relationships between test results from indirect test methods and the in-situ compressive strength;
-   provides procedures and guidance on in-situ assessment of the compressive strength class of concrete where there is doubt over the strength of concrete recently supplied to a structure or precast concrete component.
This European Standard does not include the following cases:
-   assessment based on cores less than 50 mm in diameter, micro-cores;
-   assessment of the quality of concrete for properties other than compressive strength, e.g. durability-related properties;
-   specific provisions for lightweight concretes;
-   use of pull-out testing;
-   in the Clause 8 procedures, provisions for less than 8 cores without indirect testing;
-   use of comparative testing (see CEN/TR Further guidance on the application of EN 13791:2016 and background to the provisions [1] for explanation).
(2)   This European Standard is not for the assessment of conformity of concrete compressive strength in accordance with EN 206 or EN 13369 except as indicated in EN 206:2013, 5.5.1.2 or 8.4.
(3)   This European Standard does not cover the procedures or criteria for the routine conformity control of precast concrete components using either direct or indirect measurements of the in-situ strength.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 15673:2018
Guidelines for the simplified design of structural reinforced concrete for buildings
ISO 15673:2016

This document provides guidelines for the design and construction of low-rise concrete building
structures of small area to be built in the less developed areas of the world.
This document is applicable to the planning, design and construction of structural reinforced concrete
structures to be used in new low-rise buildings of restricted occupancy, number of stories, and area.
This document can be used as an alternative to the development of a National Concrete Building Code,
or equivalent document in countries where no national design codes are available by themselves, or as
an alternative to the National Concrete Building Code in countries where specifically considered and
accepted by the national standard body or other appropriate regulatory organization.

  • Standard
    192 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    182 pages
    English language
    sale 15% off
  • Draft
    192 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1504-10:2017(Main)
Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works
EN 1504-10:2017

This part of EN 1504 gives requirements for
-   substrate condition before and during application of systems and products;
-   storage of systems and products;
-   structural stability during preparation, protection and repair;
-   methods of protection and repair;
-   quality control for execution of work;
-   maintenance of the structure.
These aspects include effects on health and safety, the working environment, the environment and the economy.

  • Standard
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13670:2010/A101:2010/AC:2017
Execution of concrete structures - National Annex - Corrigendum AC
  • Corrigendum
    2 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1766:2017(Main)
Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing
EN 1766:2017

This European Standard specifies the composition, characteristics and preparation procedure for reference concrete substrates which are to be used in the test methods to measure performance requirements of products and systems for the repair and protection of concrete structures.
The provisions of this standard are applicable to concrete with a maximum aggregate size of 16 mm or 20 mm or with a maximum aggregate size of 8 mm or 10 mm.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1504-8:2016(Main)
Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and AVCP - Part 8: Quality control and Assessment and verification of the constancy of performance (AVCP)
EN 1504-8:2016

This Part of this European Standard specifies procedures for quality control and evaluation of conformity, including marking and labelling of products and systems for the protection and repair of concrete according to EN 1504, Parts 2 to 7.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1504-5:2013(Main)
Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection
EN 1504-5:2013

This European Standard specifies requirements and conformity criteria for the identification, performance (including durability aspects) and safety of injection products for the repair and protection of concrete structures, used for: - force transmitting filling of cracks, voids and interstices in concrete (category F, see 3.1); - ductile filling of cracks, voids and interstices in concrete (category D, see 3.1); - swelling fitted filling of cracks, voids and interstices in concrete (category S, see 3.1). The performance requirements in this part of this document may not be applicable to highly specialised applications in extreme environmental conditions, e.g. cryogenic use, nor do they cover specialised circumstances such as accidental impact, e.g. due to traffic or ice, or earthquake loading, where specific performance requirements will apply.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 16204:2012
Durability - Service life design of concrete structures
ISO 16204:2012

This International Standard specifies principles and recommends procedures for the verification of the durability of concrete structures subject to: - known or foreseeable environmental actions causing material deterioration ultimately leading to failure of performance; - material deterioration without aggressiveness from the external environment of the structure, termed selfageing. This International Standard is intended for use by national standardization bodies when establishing or validating their requirements for durability of concrete structures. It may also be applied: - for the assessment of remaining service life of existing structures; and - for the design of service life of new structures provided quantified parameters on levels of reliability and design parameters are given in a national annex to this International Standard. Fatigue failure due to cyclic stress is not within the scope of this International Standard.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    31 pages
    English language
    sale 15% off