SIST EN ISO 2538:2004
(Main)Geometrical product specfications (GPS) - Series of angles and slopes on prisms (ISO 2538:1998)
Geometrical product specfications (GPS) - Series of angles and slopes on prisms (ISO 2538:1998)
Geometrische Produktspezifikation (GPS) - Reihen von Winkeln und Neigungen an Prismen (ISO 2538:1998)
Spécification géométrique des produits (GPS) - Séries d'angles et d'inclinaisons de prismes (ISO 2538:1998)
La présente Norme internationale spécifie deux séries d'angles de prismes allant de 120° à 0°30'et une série d'inclinaisons de prismes allant de 1:10 à 1:500, à l'usage de la mécanique générale.
Geometrical product specfications (GPS) - Series of angles and slopes on prisms (ISO 2538:1998)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 2538:2004
01-maj-2004
Geometrical product specfications (GPS) - Series of angles and slopes on prisms
(ISO 2538:1998)
Geometrical product specfications (GPS) - Series of angles and slopes on prisms (ISO
2538:1998)
Geometrische Produktspezifikation (GPS) - Reihen von Winkeln und Neigungen an
Prismen (ISO 2538:1998)
Spécification géométrique des produits (GPS) - Séries d'angles et d'inclinaisons de
prismes (ISO 2538:1998)
Ta slovenski standard je istoveten z: EN ISO 2538:2003
ICS:
17.040.01 Linearne in kotne meritve na Linear and angular
splošno measurements in general
SIST EN ISO 2538:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 2538:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 2538:2004
EUROPEAN STANDARD
EN ISO 2538
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2003
ICS 17.040.01
English version
Geometrical product specfications (GPS) - Series of angles and
slopes on prisms (ISO 2538:1998)
Spécification géométrique des produits (GPS) - Séries Geometrische Produktspezifikation (GPS) - Reihen von
d'angles et d'inclinaisons de prismes (ISO 2538:1998) Winkeln und Neigungen an Prismen (ISO 2538:1998)
This European Standard was approved by CEN on 15 November 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden, Switzerland and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2538:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 2538:2004
EN ISO 2538:2003 (E)
Foreword
The text of ISO 2538:1998 has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" of the International
Organization for Standardization (ISO) and has been taken over as EN ISO 2538:2003 by
Technical Committee CEN/TC 290 "Dimensional and geometrical product specification and
verification", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by August 2003, and conflicting national
standards shall be withdrawn at the latest by August 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden,
Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2538:1998 has been approved by CEN as EN ISO 2538:2003 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 2538:2004
INTERNATIONAL ISO
STANDARD 2538
Second edition
1998-09-15
Geometrical Product Specifications
(GPS) — Series of angles and slopes on
prisms
Spécification géométrique des produits (GPS) — Séries d'angles et
d'inclinaisons de prismes
A
Reference number
ISO 2538:1998(E)
---------------------- Page: 5 ----------------------
SIST EN ISO 2538:2004
ISO 2538:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO collab-
orates closely with the International Electrotechnical Commission (IEC) on
all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 2538 was prepared by the Technical Committee
ISO/TC 213, Dimensional and geometrical product specifications and
verification.
This second edition cancels and replaces the first edition (ISO 2538:1974),
of which the tables have been corrected and updated, but not technically
modified.
Annexes A and B of this International Standard are for information only.
© ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
---------------------- Page: 6 ----------------------
SIST EN ISO 2538:2004
©
ISO ISO 2538:1998(E)
Introduction
This International Standard is a geometrical product specification (GPS)
standard and is to be regarded as a general GPS standard (see
ISO/TR 14638). It influences chain links 1 and 2 of the chain of standards
on angle.
For more detailed information of the relation of this International Standard
to other standards and the GPS matrix model, see anne
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.