EN ISO 2538-1:2014
(Main)Geometrical product specifications (GPS) - Wedges - Part 1: Series of angles and slopes (ISO 2538-1:2014)
Geometrical product specifications (GPS) - Wedges - Part 1: Series of angles and slopes (ISO 2538-1:2014)
ISO 2538-1:2014 specifies terms and definitions for wedges, three series of wedge angles from 120° to 0° 30′ and a series of wedge slopes from 1:10 to 1:500, for general mechanical engineering purposes.
Geometrische Produktspezifikation (GPS) - Keile - Teil 1: Reihen von Winkeln und Neigungen (ISO 2538-1:2014)
Diese Internationale Norm legt Begriffe für Keile, drei Reihen von Keilwinkeln von 120° bis 0° 30' sowie eine Reihe von Keilsteigungen von 1:10 bis 1:500 für allgemeine technische Anwendungen fest.
Spécification géométrique des produits (GPS) - Coins - Partie 1: Séries d'angles et d'inclinaisons (ISO 2538-1:2014)
L'ISO 2538-1:2014 spécifie des termes et définitions pour coins, trois séries d'angles de coin allant de 120° à 0°30' et une série d'inclinaisons de coins allant de 1:10 à 1:500, à l'usage de la mécanique générale.
Specifikacija geometrijskih veličin izdelka (GPS) - Zagozde - 1. del: Vrste kotov in nagibov na poševninah (ISO 2538-1:2014)
Standard EN ISO 2538-1 določa izraze in definicije za zagozde, tri vrste kotov zagozd od 120° do 0° 30' in vrsto nagibov zagozd od 1 : 10 do 1 : 500 za splošne inženirske namene.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2014
1DGRPHãþD
SIST EN ISO 2538:2004
SIST ISO 2538:2001
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 =DJR]GHGHO 9UVWHNRWRYLQ
QDJLERYQDSRãHYQLQDK ,62
Geometrical product specifications (GPS) - Wedges - Part 1: Series of angles and slopes
(ISO 2538-1:2014)
Geometrische Produktspezifikation (GPS) - Keile - Teil 1: Reihen von Winkeln und
Neigungen an Prismen (ISO 2538-1:2014)
Spécification géométrique des produits (GPS) - Cales - Partie 1: Séries d'angles et
d'inclinaisons (ISO 2538-1:2014)
Ta slovenski standard je istoveten z: EN ISO 2538-1:2014
ICS:
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 2538-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2014
ICS 17.040.01 Supersedes EN ISO 2538:2003
English Version
Geometrical product specifications (GPS) - Wedges - Part 1:
Series of angles and slopes (ISO 2538-1:2014)
Spécification géométrique des produits (GPS) - Coins - Geometrische Produktspezifikation (GPS) - Keile - Teil 1:
Partie 1: Séries d'angles et d'inclinaisons (ISO 2538- Reihen von Winkeln und Neigungen (ISO 2538-1:2014)
1:2014)
This European Standard was approved by CEN on 9 August 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2538-1:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 2538-1:2014) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2015, and conflicting national standards shall be withdrawn at
the latest by March 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2538:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 2538-1:2014 has been approved by CEN as EN ISO 2538-1:2014 without any modification.
INTERNATIONAL ISO
STANDARD 2538-1
First edition
2014-09-01
Geometrical product specifications
(GPS) — Wedges —
Part 1:
Series of angles and slopes
Spécification géométrique des produits (GPS) — Coins —
Partie 1: Séries d’angles et d’inclinaisons
Reference number
ISO 2538-1:2014(E)
©
ISO 2014
ISO 2538-1:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 2538-1:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Terms and definitions . 1
3 Values . 4
Annex A (informative) Relation to the GPS matrix model . 6
Bibliography . 8
ISO 2538-1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. Th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.