Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Round laminated rolled tubes

This part of IEC 61212 gives requirements for industrial rigid round laminated rolled tubes for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties are given in Table 1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Isolierstoffe - Runde Rohre und Stäbe aus technischen Schichtpressstoffen auf der Basis warmhärtender Harze für elektrotechnische Zwecke - Teil 3: Bestimmungen für einzelne Werkstoffe - Blatt 1: Runde, gewickelte Rohre aus technischen Schichtpressstoffen

Matériaux isolants - Tubes et barres industriels rigides, ronds, stratifiés, à base de résines thermodurcissables, à usages électriques - Partie 3: Spécifications pour matériaux particuliers - Feuille 1: Tubes ronds stratifiés enroulés

La CEI 61212-3-1:2013 donne les exigences relatives aux tubes industriels rigides ronds, stratifiés, enroulés, à usages électriques, à base de différentes résines et de différents matériaux de renfort. Les applications et les propriétés distinctives sont données au Tableau 1. Les matériaux qui sont conformes à cette spécification satisfont à des niveaux de performances établis. Cependant, il convient que le choix d'un matériau par un utilisateur et pour une application particulière soit fondé sur les exigences réelles nécessaires pour obtenir les performances satisfaisantes pour cette application, et non pas fondé sur cette seule spécification. Cette troisième édition annule et remplace la deuxième édition parue en 2006. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: Les détails d'essais relatifs à la résistance d'isolement, ainsi que les valeurs d'écart admissible par rapport au diamètre extérieur nominal des tubes ronds enroulés en l'état 'enroulé et traité' après immersion dans l'eau ont été modifiés. Mots clès: tubes industriels rigides ronds, stratifiés, enroulés

Izolacijski materiali - Industrijske toge okrogle laminirane cevi in palice na osnovi duromernih smol za elektrotehnične namene - 3. del: Specifikacije za posamezne materiale - List 1: Okrogle laminirane valjane cevi

Ta del standarda IEC 61212 navaja zahteve za industrijske toge okrogle lepljene valjane cevi za električne namene glede na različne smole in različne armature. Vrste uporabe in razlikovalne lastnosti so navedene v preglednici 1. Materiali, ki so skladni s to specifikacijo, ustrezajo določenim ravnem delovanja. Vendar mora uporabnik material za specifično uporabo izbrati glede na dejanske zahteve, ki omogočajo ustrezno delovanje pri tej uporabi, in ne samo na podlagi te specifikacije. Varnostno opozorilo: Končni uporabnik je odgovoren za zagotavljanje varne uporabe metod, ki so zajete ali omenjene v tem dokumentu.

General Information

Status
Published
Publication Date
10-Jul-2013
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
10-Jul-2013
Due Date
14-Sep-2013
Completion Date
11-Jul-2013

Relations

Buy Standard

Standard
EN 61212-3-1:2013
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61212-3-1:2013
01-september-2013
,]RODFLMVNLPDWHULDOL,QGXVWULMVNHWRJHRNURJOHODPLQLUDQHFHYLLQSDOLFHQDRVQRYL
GXURPHUQLKVPRO]DHOHNWURWHKQLþQHQDPHQHGHO6SHFLILNDFLMH]DSRVDPH]QH
PDWHULDOH/LVW2NURJOHODPLQLUDQHYDOMDQHFHYL
Insulating materials - Industrial rigid round laminated tubes and rods based on
thermosetting resins for electrical purposes - Part 3: Specifications for individual
materials - Sheet 1: Round laminated rolled tubes
Isolierstoffe - Runde Rohre und Stäbe aus technischen Schichtpressstoffen auf der Basis
warmhärtender Harze für elektrotechnische Zwecke - Teil 3: Bestimmungen für einzelne
Werkstoffe - Blatt 1: Runde, gewickelte Rohre aus technischen Schichtpressstoffen
Matériaux isolants - Tubes et barres industriels rigides, ronds, stratifiés, à base de
résines thermodurcissables, à usages électriques - Partie 3: Spécifications pour
matériaux particuliers - Feuille 1: Tubes ronds stratifiés enroulés
Ta slovenski standard je istoveten z: EN 61212-3-1:2013
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
SIST EN 61212-3-1:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61212-3-1:2013

EUROPEAN STANDARD
EN 61212-3-1

NORME EUROPÉENNE
July 2013
EUROPÄISCHE NORM

ICS 29.035.01 Supersedes EN 61212-3-1:2006


English version


Insulating materials -
Industrial rigid round laminated tubes and rods based on thermosetting
resins for electrical purposes -
Part 3: Specifications for individual materials -
Sheet 1: Round laminated rolled tubes
(IEC 61212-3-1:2013)


Matériaux isolants -  Isolierstoffe – Runde Rohre und Stäbe
Tubes et barres industriels rigides, ronds, aus technischen Schichtpressstoffen auf
stratifiés, à base de résines der Basis warmhärtender Harze für
thermodurcissables, à usages électriques elektrotechnische Zwecke – Teil 3:
- Bestimmungen für einzelne Werkstoffe –
Partie 3: Spécifications pour matériaux Blatt 1: Runde, gewickelte Rohre aus
particuliers - technischen Schichtpressstoffen
Feuille 1: Tubes ronds stratifiés enroulés (IEC 61212-3-1:2013)
(CEI 61212-3-1:2013)

This European Standard was approved by CENELEC on 2013-06-03. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61212-3-1:2013 E

---------------------- Page: 2 ----------------------

SIST EN 61212-3-1:2013
EN 61212-3-1:2013 - 2 -
Foreword
The text of document 15/699/FDIS, future edition 3 of IEC 61212-3-1, prepared by IEC/TC 15 "Solid
electrical insulating materials", was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 61212-3-1:2013.
The following dates are fixed:
(dop) 2014-03-03
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2016-06-03

standards conflicting with the
document have to be withdrawn

This document supersedes EN 61212-3-1:2006.
EN 61212-3-1:2013 includes the following significant technical changes with respect to
EN 61212-3-1:2006:

Details of test for insulation resistance after immersion in water and values for permissible deviation from
nominal external diameter of round rolled tubes in the “as rolled and cured” condition are changed.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 61212-3-1:2013 was approved by CENELEC as a European
Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61212-3 series NOTE  Harmonized in EN 61212-3 series (not modified).
ISO 472:1999 NOTE  Harmonized as EN ISO 472:2001 (not modified).

---------------------- Page: 3 ----------------------

SIST EN 61212-3-1:2013
- 3 - EN 61212-3-1:2013
Annex ZA
(normative)
Normative references to i nternational publications
with their corresponding European publications


The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 61212-1 - Insulating materials - Industrial rigid round EN 61212-1 -
laminated tubes and rods based on
thermosetting resins for electrical purposes -
Part 1: Definitions, designations and general
requirements


IEC 61212-2 2006 Insulating materials - Industrial rigid round EN 61212-2 2006
laminated tubes and rods based on
thermosetting resins for electrical purposes -
Part 2: Methods of test

---------------------- Page: 4 ----------------------

SIST EN 61212-3-1:2013

---------------------- Page: 5 ----------------------

SIST EN 61212-3-1:2013



IEC 61212-3-1

®


Edition 3.0 2013-04




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Insulating materials – Industrial rigid round laminated tubes and rods based on

thermosetting resins for electrical purposes –

Part 3: Specifications for individual materials – Sheet 1: Round laminated rolled


tubes



Matériaux isolants – Tubes et barres industriels rigides, ronds, stratifiés, à base


de résines thermodurcissables, à usages électriques –

Partie 3: Spécifications pour matériaux particuliers – Feuille 1: Tubes ronds

stratifiés enroulés










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX P


ICS 29.035.01 ISBN 978-2-83220-760-4



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 6 ----------------------

SIST EN 61212-3-1:2013
– 2 – 61212-3-1 © IEC:2013
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Designations and abbreviations . 7
4.1 General . 7
4.2 Designation . 7
4.3 Abbreviations . 7
5 Requirements . 7
Bibliography . 16

Table 1 – Types of industrial round rolled tubes . 8
Table 2 – Permissible deviation from nominal external diameter of round rolled tubes
in the “as rolled and cured” condition . 9
Table 3 – Permissible deviation from nominal external diameter of round rolled tubes
in ground or turned condition, all types . 9
Table 4 – Permissible deviation from nominal internal diameter of round rolled tubes,
all types . 10
Table 5 – Tolerance on wall thickness for round rolled tubes . 10
Table 6 – Departure from straightness for round rolled tubes . 11
Table 7– Property requirements for round rolled tubes . 12
Table 8 – Electric strength at 90 °C in oil, perpendicular to laminations, for round
a
rolled tubes (1 min proof test or 20 s step-by-step test) (kV/mm) . 15

---------------------- Page: 7 ----------------------

SIST EN 61212-3-1:2013
61212-3-1 © IEC:2013 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

INSULATING MATERIALS – INDUSTRIAL RIGID ROUND
LAMINATED TUBES AND RODS BASED ON THERMOSETTING
RESINS FOR ELECTRICAL PURPOSES –

Part 3: Specifications for individual materials –
Sheet 1: Round laminated rolled tubes

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61212-3-1 has been prepared by IEC technical committee 15:
Solid electrical insulating materials.
This third edition cancels and replaces the second edition published in 2006. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
Details of test for insulation resistance after immersion in water and values for permissible
deviation from nominal external diameter of round rolled tubes in the “as rolled and cured”
condition are changed.

---------------------- Page: 8 ----------------------

SIST EN 61212-3-1:2013
– 4 – 61212-3-1 © IEC:2013
The text of this standard is based on the following documents:
FDIS Report on voting
15/699/FDIS 15/709/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 61212 series, under the general title Insulating materials –
Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical
purposes, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 9 ----------------------

SIST EN 61212-3-1:2013
61212-3-1 © IEC:2013 – 5 –
INTRODUCTION
This part of IEC 61212 is one of a series which deals with industrial rigid round laminated
tubes and rods based on thermosetting resins for electrical purposes.
This series consists of three parts:
Part 1: Definitions, designations and gen
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.