SIST EN ISO 11642:2013
(Main)Leather - Tests for colour fastness - Colour fastness to water (ISO 11642:2012)
Leather - Tests for colour fastness - Colour fastness to water (ISO 11642:2012)
This International Standard specifies a method for determining the colour fastness to water of leather of all kinds at all stages of processing.
Leder - Farbechtheitsprüfungen - Farbechtheit gegenüber Wasser (ISO 11642:2012)
Diese Internationale Norm legt ein Verfahren fest zur Bestimmung der Farbechtheit aller Arten von Leder in allen Verarbeitungsstufen gegenüber Wasser.
Cuir - Essais de solidité des coloris - Solidité des coloris à l'eau (ISO 11642:2012)
L'ISO 11642:2012 spécifie une méthode permettant de déterminer la solidité des coloris à l'eau des cuirs de toutes catégories à toutes les phases du traitement.
Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti vodi (ISO 11642:2012)
Ta mednarodni standard določa metodo za določevanje obstojnosti barve proti vodi za usnje vseh vrst in na vseh stopnjah obdelave.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti vodi (ISO 11642:2012)Leder - Farbechtheitsprüfungen - Farbechtheit gegenüber Wasser (ISO 11642:2012)Cuir - Essais de solidité des coloris - Solidité des coloris à l'eau (ISO 11642:2012)Leather - Tests for colour fastness - Colour fastness to water (ISO 11642:2012)59.140.30Usnje in krznoLeather and fursICS:Ta slovenski standard je istoveten z:EN ISO 11642:2012SIST EN ISO 11642:2013en01-november-2013SIST EN ISO 11642:2013SLOVENSKI
STANDARDSIST EN ISO 11642:20001DGRPHãþD
SIST EN ISO 11642:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 11642
November 2012 ICS 59.140.30 Supersedes EN ISO 11642:1998English Version
Leather - Tests for colour fastness - Colour fastness to water (ISO 11642:2012)
Cuir - Essais de solidité des coloris - Solidité des coloris à l'eau (ISO 11642:2012)
Leder - Farbechtheitsprüfungen - Farbechtheit gegenüber Wasser (ISO 11642:2012) This European Standard was approved by CEN on 14 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11642:2012: ESIST EN ISO 11642:2013
EN ISO 11642:2012 (E) 2 Contents Page Foreword .3SIST EN ISO 11642:2013
EN ISO 11642:2012 (E) 3 Foreword This document (EN ISO 11642:2012) has been prepared by Technical Committee CEN/TC 289 “Leather", the secretariat of which is held by UNI, in collaboration with the International Union of Leather Technologists and Chemists Societies. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 11642:1998. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11642:2012 has been approved by CEN as a EN ISO 11642:2012 without any modification.
SIST EN ISO 11642:2013
SIST EN ISO 11642:2013
Reference numberISO 11642:2012(E)IULTCS/IUF 421:2012(E)© ISO 2012
INTERNATIONAL STANDARD ISO11642IULTCS/IUF421Second edition2012-11-15Leather — Tests for colour fastness — Colour fastness to water Cuir — Essais de solidité des coloris — Solidité des coloris à l'eau
SIST EN ISO 11642:2013
ISO 11642:2012(E) IULTCS/IUF 421:2012(E)
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2012 – All rights reserved
SIST EN ISO 11642:2013
ISO 11642:2012(E) IULTCS/IUF 421:2012(E) © ISO 2012 – All rights reserved iii Contents Page Foreword . iv 1 Scope . 1 2 Normative references . 1 3 Principle . 2 4 Apparatus and materials. 2 5 Test specimens . 3 6 Procedure . 3 7 Evaluation . 4 8 Precision . 4 9 Test report . 4 Annex A (informative)
Commercial sources for apparatus and materials . 5
SIST EN ISO 11642:2013
ISO 11642:2012(E) IULTCS/IUF 421:2012(E) iv © ISO 2012 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11642 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, in collaboration with the Fastness Tests Commission of the International Union of Leather Technologists and Chemists Societies (IUF Commission, IULTCS), in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
The first edition of ISO 11642 was based on IUF 421 published in J. Soc. Leather Tech. Chem., 71, pp. 21-22, (1987), and declared an official method of the IULTCS in October 1989. This second edition of ISO 11642 cancels and replaces the first edition (ISO 11642:1993). This new version is an general update of the procedures and includes the option for instrumental grey scale evaluation (7.2). IULTCS, originally formed in 1897, is a worldwide organization of professional leather societies to further the advancement of leather science and technology. IULTCS has three Commissions, which are responsible for establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as an international standardizing body for the preparation of test methods for leather.
SIST EN ISO 11642:2013
INTERNATIONAL STANDARD ISO 11642:2012(E)IULTCS/IUF 421:2012(E) © ISO 2012 – All rights reserved 1 Leather — Tests for colour fastness — Colour fastness to water 1 Scope This International Standard specifies a method for determining the colour fastness to water of leather of all kinds at all stages of processing. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 105-A01, Textiles — Tests for colour fastness — Part A01: General principles of testing ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour ISO 105-A03, Textiles — Tests for colour fastness — Part A03: Grey scale for assessing staining ISO 105-A04, Textiles — Tests for col
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.