SIST EN ISO 19064-1:2016
(Main)Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19064-1:2015)
Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19064-1:2015)
This part of ISO 19064 establishes a system of designation for styrene/acrylonitrile (SAN) moulding
and extrusion materials, which may be used as the basis for specifications.
The types of styrene/acrylonitrile plastic are differentiated from each other by a classification system
based on appropriate levels of the designatory properties,
a) Vicat softening temperature,
b) melt mass-flow rate,
and on information about composition, intended application and/or method of processing, important
properties, additives, colorants, fillers and reinforcing materials.
This part of ISO 19064 is applicable to all copolymers of styrene and/or substituted styrene having
between 5 % (m/m) and 50 % (m/m) acrylonitrile.
It applies to materials ready for normal use, unmodified or modified by colorants, additives, fillers, etc.
This part of ISO 19064 does not apply to expandable materials.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This part of ISO 19064 does not provide engineering data, performance data or data on
processing conditions which may be required to specify a material for a particular application and/or
method of processing.
If such additional properties are required, they shall be determined in accordance with the test methods
specified in ISO 4894-2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, additional requirements may be given in data block 5 (see 3.1).
Kunststoffe - Styrol/Acrylnitril (SAN)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 19064-1:2015)
Der vorliegende Teil von ISO 19064 legt ein System für die Bezeichnung von Styrol/Acrylnitril (SAN)-Formmassen fest, das als Grundlage für Spezifikationen angewendet werden darf.
Die Typen der Styrol/Acrylnitril (SAN)-Formmassen werden mit Hilfe eines Einteilungssystems vonein-ander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften
a) Vicat-Erweichungstemperatur;
b) Schmelze-Massefließrate;
und auf Informationen über die Zusammensetzung, vorgesehene Anwendung und/oder Verarbeitungs-verfahren, wichtige Eigenschaften, Additive (Zusatzstoffe), Farbstoffe, Füll- und Verstärkungsstoffe beruht.
Dieser Teil von ISO 19064 gilt für alle Copolymere des Styrols und/oder substituierten Styrols mit einem Acrylnitrilgehalt von 5 % (Massenanteil) bis 50 % (Massenanteil).
Er gilt für gebrauchsfertige Formmassen, die unmodifiziert oder mit Farbstoffen, Zusatzstoffen, Füllstoffen usw. modifiziert sind.
Dieser Teil von ISO 19064 gilt nicht für schäumbare Formmassen.
Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise das Gleiche leisten. Dieser Teil von ISO 19064 enthält keine technischen Daten, Leistungsangaben oder Angaben zu Verarbeitungsbedingungen, die notwendig sein können, um eine Formmasse für eine bestimmte Anwen-dung und/oder Verarbeitungsart zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften erforderlich sind, müssen diese nach dem in der ISO 4894 2 festgelegten Prüfverfahren, soweit geeignet, bestimmt werden.
Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen im Datenblock 5 (siehe 3.1) zusätzliche Anforderungen gestellt werden.
Plastiques - Styrène/acrylonitrile (SAN) pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 19064-1:2015)
ISO 19064-1:2015 établit un système de désignation des matériaux styrène/acrylonitrile (SAN) pour moulage et extrusion, qui peut être utilisé comme base pour les spécifications.
Les types de plastique styrène/acrylonitrile sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés de propriétés de désignation,
a) température de ramollissement Vicat,
b) indice de fluidité à chaud en masse,
et des informations concernant la composition, l'application prévue et/ou la méthode de mise en ?uvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
ISO 19064-1:2015 est applicable à tous les copolymères de styrène et/ou de styrène substitué contenant 10 % (m/m) et 50 % (m/m) d'acrylonitrile.
Elle s'applique aux matériaux prêts à l'emploi normal, non modifiés ou modifiés par des colorants, additifs, charges etc.
ISO 19064-1:2015 ne s'applique pas aux matériaux extensibles.
Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. La présente partie de l'ISO 19064 ne comporte pas de données sur la conception, la performance ou les conditions de mise en ?uvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en ?uvre particulière.
Si de telles caractéristiques additionnelles sont nécessaires, elles doivent être déterminées conformément aux méthodes d'essai prescrites dans l'ISO 4894‑2, si appropriée.
Afin de prescrire un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en ?uvre reproductible, des exigences additionnelles peuvent être codées dans le bloc de données 5 (voir 3.1).
Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz kopolimerov stiren-akrilonitrila (SAN) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 19064-1:2015)
Ta del standarda ISO 19064 določa sistem označevanja materialov za oblikovanje
in ekstrudiranje iz kopolimerov stiren-akrilonitrila (SAN), ki jih je mogoče uporabiti kot podlago za specifikacije.
Vrste polimernih materialov na osnovi stiren-akrilonitrila se ločujejo glede na sistem razvrščanja,
ki temelji na ustreznih ravneh označevalnih lastnosti:
a) temperaturi zmehčišča po Vicatu,
b) prostorninskem pretoku taline
in informacijah o sestavi, nameravani uporabi in/ali metodi obdelave, pomembnih
lastnostih, aditivih, barvilih, polnilih ter materialih za ojačanje.
Ta del standarda ISO 19064 velja za vse kopolimere stirena in/ali zamenjanega stirena z vsebnostjo akrilonitrila med 5 % (m/m) in 50 % (m/m).
Uporablja se za materiale, pripravljene za običajno uporabo, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.
Ta del standarda ISO 19064 ne velja za razširljive materiale.
Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta del standarda ISO 19064 ne zagotavlja inženirskih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so lahko potrebni za določitev materiala za določeno uporabo in/ali metodo obdelave.
Če so take dodatne lastnosti zahtevane, jih je treba določiti v skladu s preskusnimi metodami
iz standarda ISO 4894-2, če je to primerno. Da bi se določil termoplastični material za določeno uporabo ali da bi se zagotovila obnovljiva obdelava, se lahko v podatkovnem bloku 5 navedejo dodatne zahteve (glej točko 3.1).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19064-1:2016
01-februar-2016
1DGRPHãþD
SIST EN ISO 4894-1:2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]NRSROLPHURYVWLUHQ
DNULORQLWULOD 6$1 GHO 6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH ,62
Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1:
Designation system and basis for specifications (ISO 19064-1:2015)
Kunststoffe - Styrol/Acrylnitril (SAN)-Formmassen - Teil 1: Bezeichnungssystem und
Basis für Spezifikationen (ISO 19064-1:2015)
Plastiques - Styrène/acrylonitrile (SAN) pour moulage et extrusion - Partie 1: Système de
désignation et base de spécification (ISO 19064-1:2015)
Ta slovenski standard je istoveten z: EN ISO 19064-1:2015
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 19064-1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19064-1:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 19064-1:2016
EN ISO 19064-1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2015
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 4894-1:1999
English Version
Plastics - Styrene/acrylonitrile (SAN) moulding and
extrusion materials - Part 1: Designation system and basis
for specifications (ISO 19064-1:2015)
Plastiques - Styrène/acrylonitrile (SAN) pour moulage Kunststoffe - Styrol/Acrylnitril (SAN)-Formmassen -
et extrusion - Partie 1 : Système de désignation et base Teil 1: Bezeichnungssystem und Basis für
de spécification (ISO 19064-1:2015) Spezifikationen (ISO 19064-1:2015)
This European Standard was approved by CEN on 26 September 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19064-1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19064-1:2016
EN ISO 19064-1:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19064-1:2016
EN ISO 19064-1:2015 (E)
European foreword
This document (EN ISO 19064-1:2015) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 4894-1:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19064-1:2015 has been approved by CEN as EN ISO 19064-1:2015 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 19064-1:2016
---------------------- Page: 6 ----------------------
SIST EN ISO 19064-1:2016
INTERNATIONAL ISO
STANDARD 19064-1
First edition
2015-11-15
Plastics — Styrene/acrylonitrile (SAN)
moulding and extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Styrène/acrylonitrile (SAN) pour moulage et extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 19064-1:2015(E)
©
ISO 2015
---------------------- Page: 7 ----------------------
SIST EN ISO 19064-1:2016
ISO 19064-1:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19064-1:2016
ISO 19064-1:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Designation system . 2
3.1 General . 2
3.2 Data block 1 . 2
3.3 Data block 2 . 3
3.4 Data block 3 . 3
3.5 Data block 4 . 4
3.5.1 Vicat softening temperature . 4
3.5.2 Melt mass-flow rate . 5
3.6 Data block 5 . 5
4 Examples of designations . 5
© ISO 2015 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 19064-1:2016
ISO 19064-1:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 19064-1 cancels and replaces ISO 4894-1:1997, which has been technically
revised to introduce a new designation system.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 4894-1. If the existing ISO 4894-1 would be replaced by the new designation system, these
documents would refer to the incorrect designation system.
In order to give users time to switch from ISO 4894-1 to ISO 19064-1, any designation system according
to ISO 4894-1 is to be phased out in 5 to 10 years. During this period, ISO 4894-2 will effectively be Part
2 of this International Standard.
ISO 19064 consists of the following parts, under the general title Plasti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.