SIST EN ISO 15181-1:2007

Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 1: General method for extraction of biocides (ISO 15181-1:2007)

This part of ISO 15181 specifies a general method for extracting biocides from antifouling paint films into artificial seawater under specified laboratory conditions. It is used in conjunction with the other parts of ISO 15181 to determine the amounts of specific biocides in the extract, for example copper and/or certain organic biocides, and to enable the release rate of those biocides from the paint film under the specified laboratory conditions to be calculated.

Beschichtungsstoffe - Bestimmung der Auswaschrate von Bioziden aus Antifouling-Beschichtungen - Teil 1: Allgemeines Verfahren zur Extraktion von Bioziden (ISO 15181-1:2007)

Dieser Teil von ISO 15181 legt ein allgemeines Verfahren zum Extrahieren von Bioziden aus Antifouling-Beschichtungen mit künstlichem Meerwasser unter festgelegten Bedingungen fest. Das Verfahren wird in Verbindung mit anderen Teilen von ISO 15181 zum Bestimmen des Gehaltes an bestimmten Bioziden im Extrakt, zum Beispiel Kupfer und/oder bestimmte organische Biozide, unter festgelegten Laborbedingungen und zum Berechnen der Auswaschrate des Biozids aus der Beschichtung angewendet.

Peintures et vernis - Détermination du taux de lixiviation des biocides contenus dans les peintures antisalissures - Partie 1: Méthode générale d'extraction des biocides (ISO 15181-1:2007)

L'ISO 15181-1:2007 spécifie une méthode générale d'extraction des biocides contenus dans les feuils de peintures antisalissures dans une eau de mer synthétique et dans des conditions spécifiées de laboratoire. Elle est utilisée en liaison avec d'autres parties de l'ISO 15181 pour déterminer la teneur en biocides spécifiques contenus dans l'extrait, par exemple cuivre et/ou certains biocides organiques, et permettre le calcul du taux de lixiviation de biocides contenus dans le feuil de la peinture dans des conditions spécifiées de laboratoire.

Barve in laki - Določanje razmerja sproščanja biocidov iz barv proti obraščanju - 1. del: Splošna metoda za ekstrakcijo biocidov (ISO 15181-1:2007)

General Information

• Status: Published
• Publication Date: 03-Jul-2007
• ICS: 87.040 - Paints and varnishes
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Jun-2007
• Due Date: 18-Aug-2007
• Completion Date: 04-Jul-2007
• Ref Project: EN ISO 15181-1:2007 - Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 1: General method for extraction of biocides (ISO 15181-1:2007)

Relations

• Replaces: SIST EN ISO 15181-1:2004 - Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 1: General method for extraction of biocides (ISO 15181-1:2000)
• Effective Date: 01-Jul-2007

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15181-1:2007
01-julij-2007
1DGRPHãþD
SIST EN ISO 15181-1:2004
%DUYHLQODNL'RORþDQMHUD]PHUMDVSURãþDQMDELRFLGRYL]EDUYSURWLREUDãþDQMX
GHO6SORãQDPHWRGD]DHNVWUDNFLMRELRFLGRY,62
Paints and varnishes - Determination of release rate of biocides from antifouling paints -
Part 1: General method for extraction of biocides (ISO 15181-1:2007)
Beschichtungsstoffe - Bestimmung der Auswaschrate von Bioziden aus Antifouling-
Beschichtungen - Teil 1: Allgemeines Verfahren zur Extraktion von Bioziden (ISO 15181-
1:2007)
Peintures et vernis - Détermination du taux de lixiviation des biocides contenus dans les
peintures antisalissures - Partie 1: Méthode générale d'extraction des biocides (ISO
15181-1:2007)
Ta slovenski standard je istoveten z: EN ISO 15181-1:2007
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 15181-1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 15181-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 87.040 Supersedes EN ISO 15181-1:2004
English Version
Paints and varnishes - Determination of release rate of biocides
from antifouling paints - Part 1: General method for extraction of
biocides (ISO 15181-1:2007)
Peintures et vernis - Détermination du taux de lixiviation Beschichtungsstoffe - Bestimmung der Auswaschrate von
des biocides contenus dans les peintures antisalissures - Bioziden aus Antifouling-Beschichtungen - Teil 1:
Partie 1: Méthode générale d'extraction des biocides (ISO Allgemeines Verfahren zur Extraktion von Bioziden (ISO
15181-1:2007) 15181-1:2007)
This European Standard was approved by CEN on 16 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15181-1:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 15181-1:2007 (E)





Foreword


This document (EN ISO 15181-1:2007) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 "Paints and
varnishes", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.

This document supersedes EN ISO 15181-1:2004.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.


Endorsement notice

The text of ISO 15181-1:2007 has been approved by CEN as EN ISO 15181-1:2007 without any
modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 15181-1
Second edition
2007-06-01

Paints and varnishes — Determination of
release rate of biocides from antifouling
paints —
Part 1:
General method for extraction of biocides
Peintures et vernis — Détermination du taux de lixiviation des biocides
contenus dans les peintures antisalissures —
Partie 1: Méthode générale d'extraction des biocides



Reference number
ISO 15181-1:2007(E)
©
ISO 2007

---------------------- Page: 4 ----------------------

ISO 15181-1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 5 ----------------------

ISO 15181-1:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Principle. 2
4 Required supplementary information. 2
5 Apparatus. 2
6 Reagents and materials . 4
7 Sampling. 5
8 Preparation of test cylinders . 5
9 Procedure. 6
10 Extraction method . 6
11 Test report. 7
Annex A (normative) Supplementary information . 8
Bibliography . 9

© ISO 2007 – All rights reserved iii

---------------------- Page: 6 ----------------------

ISO 15181-1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15181-1 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
This second edition cancels and replaces the first edition (ISO 15181-1:2000), which has been technically
revised, in particular to extend the use of the general extraction method to the later parts of ISO 15181.
ISO 15181 consists of the following parts, under the general title Paints and varnishes — Determination of
release rate of biocides from antifouling paints:
⎯ Part 1: General method for extraction of biocides
⎯ Part 2: Determination of copper-ion concentration in the extract and calculation of the release rate
⎯ Part 3: Calculation of the zinc ethylene-bis(dithiocarbamate) (zineb) release rate by determination of the
concentration of ethylenethiourea in the extract
⎯ Part 4: Determination of pyridine-triphenylborane (PTPB) concentration in the extract and calculation of
the release rate
⎯ Part 5: Calculation of the tolylfluanid and dichlofluanid release rate by determination of the concentration
of dimethyltolylsulfamide (DMST) and dimethylphenylsulfamide (DMSA) in the extract
iv © ISO 2007 – All rights reserved

---------------------- Page: 7 ----------------------

ISO 15181-1:2007(E)
Introduction
By using standard conditions of temperature, salinity and pH at low biocide concentrations in the surrounding
artificial seawater, a repeatable value of the release rate under the specified laboratory conditions can be
determined using the method given in this part of ISO 15181, which can be used for quality assurance and
material selection purposes. The actual release rate of biocides from antifouling paints on ships' hulls into the
environment will, however, depend on many factors, such as ship operating schedules, length of service,
berthing conditions, paint condition, as well as the temperature, salinity, pH, pollutants and biological
community in a particular area.
The results of this test do not reflect environmental biocide release rates for antifouling products and are not
suitable for direct use in the process of generating environmental-risk assessments, producing environmental-
loading estimates or for establishing release rate limits for regulatory purposes. In comparison with copper
and organotin release rates obtained either by direct or indirect measurements of the copper release rate from
ships' hulls and from measurements made on panels exposed in harbours, all available data indicate that the
results obtained using this generic test method significantly overestimate the release rates of biocides under
in-service conditions. Published results demonstrate that the results of this test method are generally higher
than direct in situ measurements of copper and organotin release rates from in-service ship hulls by a factor of
[1, 2]
about 10 or more for several commercial antifouling coatings . A similar relationship is expected to be
found for other biocides. Realistic estimates of the biocide release rate from a ship’s hull under in-service
conditions can only be obtained from this test method if this difference is taken into account.
Where the results of this test method are used in the process of generating environmental-risk assessments,
producing environmental-loading estimates or for regulatory purposes, it is most strongly recommended that
the relationship between laboratory release rates and actual environmental inputs be taken into account to
allow a more accurate estimate of the biocide release rate from antifouling coatings under real-life conditions
[2]
to be obtained. This can be accomplished through the application of appropriate correction factors .

© ISO 2007 – All rights reserved v

---------------------- Page: 8 ----------------------

INTERNATIONAL STANDARD ISO 15181-1:2007(E)

Paints and varnishes — Determination of release rate
of biocides from antifouling paints —
Part 1:
General method for extraction of biocides
1 Scope
This part of ISO 15181 specifies a general method for extracting biocides from antifouling paint films into
artificial seawater under specified laboratory conditions. It is used in conjunction with the other parts of
ISO 15181 to determine the amounts of specific biocides in the extract, for example copper and/or certain
organic biocides, and to enable the release rate of those biocides from the paint film under the specified
laboratory conditions to be calculated.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1513, Paints and varnishes — Examination and preparation of samples for testing
ISO 2808, Paints and varnishes — Determination of film thickness
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 15181-2, Paints and varnishes — Determination of release rate of biocides from antifouling paints —
Part 2: Determination of copper-ion concentration in the extract and calculation of the release rate
ISO 15181-3, Paints and varnishes — Determination of release rate of biocides from antifouling paints —
Part 3: Calculation of the zinc ethylene-bis(dithiocarbamate) (zineb) release rate by determination of the
concentration of ethylenethiourea in the extract
ISO 15181-4, Paints and varnishes — Determination of release rate of biocides from antifouling paints —
Part 4: Determination of pyridine-triphenylborane (PTPB) concentration in the extract and calculation of the
release rate
ISO 15181-5, Paints and varnishes — Determination of release rate of biocides from antifouling paints —
Part 5: Calculation of the tolylfluanid and dichlofluanid release rate by determination of the concentration of
dimethyltolylsulfamide (DMST) and dimethylphenylsulfamide (DMSA) in the extract
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
ASTM D 1141-98(2003), Standard Practice for the Preparation of Substitute Ocean Water
© ISO 2007 – All rights reserved 1

---------------------- Page: 9 ----------------------

ISO 15181-1:2007(E)
3 Principle
Test cylinders painted with an
...