SIST EN 383:2007
(Main)Timber Structures - Test methods - Determination of embedment strength and foundation values for dowel type fasteners
Timber Structures - Test methods - Determination of embedment strength and foundation values for dowel type fasteners
This standard specifies laboratory methods to determine the embedding strength and foundation values of solid timber, glued laminated timber and wood based sheet products with dowel type fasteners.
Holzbauwerke - Prüfverfahren - Bestimmung der Lochleibungsfestigkeit und Bettungswerte für stiftförmige Verbindungsmittel
Diese Norm legt Laborverfahren zur Bestimmung der Lochleibungsfestigkeit und der Bettungswerte für Vollholz, Brettschichtholz und Holzwerkstoffplatten mit stiftförmigen Verbindungsmitteln fest.
Structures en bois - Méthodes d'essai - Détermination de caractéristiques de fondation et de la portance locale d'éléments d'assemblage de type broche
La présente norme spécifie les méthodes de laboratoire permettant de déterminer les caractéristiques de fondation et la portance locale du bois massif, du lamellé-collé et des panneaux a base de bois contenant des éléments d’assemblage de type broche.
Lesene konstrukcije - Preskusne metode - Ugotavljanje bočne trdnosti in modulov stisljivosti mehanskih spojnih sredstev paličastih oblik
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Timber Structures - Test methods - Determination of embedment strength and foundation values for dowel type fastenersStructures en bois - Méthodes d'essai - Détermination de caractéristiques de fondation et de la portance locale d'éléments d'assemblage de type brocheHolzbauwerke - Prüfverfahren - Bestimmung der Lochleibungsfestigkeit und Bettungswerte für stiftförmige VerbindungsmittelTa slovenski standard je istoveten z:EN 383:2007SIST EN 383:2007en;fr;de91.080.20Lesene konstrukcijeTimber structuresICS:SLOVENSKI
STANDARDSIST EN 383:200701-julij-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 383January 2007ICS 91.080.20Supersedes EN 383:1993
English VersionTimber Structures - Test methods - Determination ofembedment strength and foundation values for dowel typefastenersStructures en bois - Méthodes d'essai - Détermination decaractéristiques de fondation et de la portance localed'éléments d'assemblage de type brocheHolzbauwerke - Prüfverfahren - Bestimmung derLochleibungsfestigkeit und Bettungswerte für stiftförmigeVerbindungsmittelThis European Standard was approved by CEN on 25 October 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 383:2007: E
EN 383:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Symbols and abbreviations.4 5 Requirements.5 6 Test methods.5 6.1 Principle.5 6.2 Test Pieces.5 6.3 Apparatus.8 6.4 Preparation of the test pieces.8 6.5 Procedure.9 6.5.1 Apparatus calibration.9 6.5.2 Placing fastener.9 6.5.3 Placing of test piece in apparatus.9 6.5.4 Transducer location.9 6.5.5 Estimation of maximum load.9 6.5.6 Application of load.9 6.5.7 Recording of deformation.9 6.5.8 Determination of density and moisture content.10 6.6 Results.10 6.6.1 Calculations.10 6.6.2 Adjustments.14 6.7 Test report.14
EN 383:2007 (E) 3 Foreword This document (EN 383:2007) has been prepared by Technical Committee CEN/TC 124 “Timber Structures”, the secretariat of which is held by SFS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2007, and conflicting national standards shall be withdrawn at the latest by July 2007. This document supersedes EN 383:1993. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 383:2007 (E) 4 1 Scope This standard specifies laboratory methods to determine the embedding strength and foundation values of solid timber, glued laminated timber and wood based sheet products with dowel type fasteners.
2 Normative references Not applicable. 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply.
3.1 dowel type fastener bolt, nail, dowel or the like with plain or patterned surfaces
3.2 embedment strength average compressive stress at maximum load in a piece of timber or wood based sheet product under the action of a stiff linear fastener. The fastener's axis is perpendicular to the surface of the timber. The fastener is loaded perpendicular to its axis
3.3 maximum load
maximum load measured before the deformation of the specimen has reached the deformation limit
3.4 fastener section dimension
1) Nominal diameter of round fasteners; or
2) Length of one side of the section of a square fastener; or
3) Minimum dimension of the section of an oval or rectangular fastener.
4 Symbols and abbreviations d
fastener section dimension, in millimetres
F
load, in newtons
F max
maximum load, in newtons
Fmax, est
estimated maximum load, in newtons
fh
embedding strength, in newtons per square millimetre fh,est
estimated embedding strength, in newtons per square millimetre Ke
elastic foundation modulus, in newtons per cubic millimetre
Ki
initial foundation modulus, in newtons per cubic millimetre
Ks
foundation modulus, in newtons per cubic millimetre
EN 383:2007 (E) 5 t
thickness, in millimetres
w
indentation or deformation, in millimetres
we
elastic deformation, in millimetres
wi
initial deformation, in millimetres
wi,mod
modified initial deformation, in millimetres
wo
deformation of the test apparatus at any given load, in millimetres 5 Requirements The fasteners and the timber, glued laminated timber or wood based sheet product shall be, as far as possible, of the mini
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.