iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 483:2001

(Main)

Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW

Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW

This standard specifies the requirements and test methods concerning, in particular, the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or premixed burners, and that are hereafter referred to as "boilers".

Heizkessel für gasförmige Brennstoffe - Heizkessel des Typs C mit einer Nennwärmebelastung gleich oder kleiner als 70 kW

Diese Europäische Norm legt die Anforderungen und wirtschaftlichen Prüfungen insbesondere für den Bau, die Sicherheit, die Funktion und den Energieeinsatz sowie die Einteilung und die Kennzeichnung von Heizkesseln fest, die mit atmosphärischen Brennern mit und ohne Ventilator oder mit Vormischbrennern ausgerüstet sind und mit gasförmigen Brennstoffen betrieben werden (nachfolgend kurz "Kessel" genannt).

Chaudieres de chauffage central utilisant les combustibles gazeux - Chaudieres des types C dont le débit calorifique nominal est inférieur ou égal a 70 kW

Cette norme européenne prescrit les spécifications et les techniques d'essai relatives notamment a la construction, la sécurité, l'aptitude a la fonction et l'utilisation rationnelle de l'énergie ainsi que la classification et le marquage des chaudieres de chauffage central, équipées de bruleurs atmosphériques, de bruleurs atmosphériques assistés d'un ventilateur ou de bruleurs a prémélange total utilisant les combustibles gazeux, appelées ci-apres "chaudieres".

Plinski kotli za centralno ogrevanje - Tip kotlov C z imensko močjo do vključno 70 kW

General Information

Status
Withdrawn
Publication Date
31-Jan-2001
Withdrawal Date
30-Dec-2012
ICS
91.140.10 - Central heating systems
97.100.20 - Gas heaters
Technical Committee
PLN - Gas appliances for domestic use
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
11-Dec-2012
Due Date
03-Jan-2013
Completion Date
31-Dec-2012
Directive
2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
2016/426 - REGULATION (EU) 2016/426 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 9 March 2016 on appliances burning gaseous fuels and repealing Directive 2009/142/EC
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
EN 483:1999 - Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW

Relations

Amended By
SIST EN 483:2001/A2:2002 - Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
Effective Date
01-Apr-2002
Replaced By
SIST EN 15502-2-1:2013 - Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
Effective Date
01-Jan-2013
Corrected By
SIST EN 483:2001/A2:2002/AC:2006 - Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
Effective Date
08-Jun-2022
Amended By
SIST EN 483:2001/A4:2008 - Gas fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
Effective Date
08-Jun-2022
Amended By
SIST EN 483:2001/A2:2002 - Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
Effective Date
08-Jun-2022
Amended By
SIST EN 483:2001/A4:2008 - Gas fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
Effective Date
01-Mar-2008

Buy Standard

EN 483:2001EN 483:2001
PreviousNext
Standard
EN 483:2001
English language
136 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.N:Heizkessel für gasförmige Brennstoffe - Heizkessel des Typs C mit einer Nennwärmebelastung gleich oder kleiner als 70 kWChaudieres de chauffage central utilisant les combustibles gazeux - Chaudieres des types C dont le débit calorifique nominal est inférieur ou égal a 70 kWGas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW97.100.20Plinski grelnikiGas heaters91.140.10Sistemi centralnega ogrevanjaCentral heating systemsICS:Ta slovenski standard je istoveten z:EN 483:1999SIST EN 483:2001en01-februar-2001SIST EN 483:2001SLOVENSKI
STANDARD



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



SIST EN 483:2001



...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 15502-1:2022/AC:2023(Corrigendum)
Gas-fired heating boilers - Part 1: General requirements and tests
EN 15502-1:2021/AC:2022

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15502-2-1:2022(Main)
Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
EN 15502-2-1:2022

This European Standard specifies, the requirements and test methods concerning, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This document is to be used in conjunction with FprEN15502-1:2020
This European Standard covers gas-fired central heating boilers from the types C1 up to C9 and the types B2, B3 and B5:
NOTE   For further background information on appliance types see EN 1749:2020.
a)   that have a nominal heat input (on the basis of net calorific value) not exceeding 1 000 kW;
b)   that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2018;
c)   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
e)   which can give rise to condensation under certain circumstances;
f)   which are declared in the instructions for installation to be either a “condensing” boiler or a "low temperature boiler" or a “standard boiler”; if no declaration is given the boiler is to be considered a “standard boiler”;
g)   which are intended to be installed inside a building or in a partially protected place;
h)   which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.;
i)   which are designed for either sealed water systems or for open water systems;
j)   which are either modular boilers, or non modular boilers.
k) which are from the types C(10) that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa, and C(11) that have condensing boiler modules that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa."
NOTE   This European Standard provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard, the risk associated with this alternative construction needs to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard does not cover all the requirements for:
aa)   Appliances above 1000 kW
ab) Appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex XC);"
ac)   Appliances using flue dampers;
ad)   Appliances of the types B21, B31, B51, C21, C41, C51, C61, C71, C81 ,C(12) and C(13);"
ae)   C7 appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
af)   Appliances incorporating flexible plastic flue liners;
ag)   C(10) boilers:
1)    without a gas-air ratio control, or
2)    which are non-condensing appliances, or
3)    which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));
ah)   C(11) boilers that have boiler modules:
1)    without a gas-air ratio control, or
2)    which are non-condensing appliances, or
3)    which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));"
ai)   Appliances intended to be connected to a (common) flue having mechanical extraction.
aj)   surface temperatures of external parts particular to children and elderly people
ak)   appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas.
al)    appliances equipped with an adaptive combustion control function (ACCF).
am)   boilers intended to be installed in areas accessible to elderly people and children

  • Standard
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    109 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15502-1:2022(Main)
Gas-fired heating boilers - Part 1: General requirements and tests
EN 15502-1:2021

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Standard
    213 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    215 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15502-2-2:2014(Main)
Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances of a nominal heat input not exceeding 70 kW
EN 15502-2-2:2014

EN 15502-2-2 specifies, the requirements and test methods concerning, in particular the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners and are hereafter referred to as “boilers”. Where the word boiler is used, this is to be read as the boiler including its connecting ducts, ducts and terminals, if any. This European Standard covers gas-fired central heating boilers type B11, B11BS, B12, B12BS, B13, B13BS according to the classification in CEN/TR 1749:2009: a) that have a nominal heat input (on the basis of net calorific value) not exceeding 70 kW; b) that use one or more combustible gases of the three gas families at the pressures stated in EN 437; c) where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation; d) where the maximum operating pressure in the water circuit does not exceed 6 bar; e) which are declared in the technical instructions to be either a “low temperature boiler” or a “standard boiler”. If no declaration is given the boiler is to be considered a “standard boiler”; f) which are intended to be installed either indoors or in a partially protected place; g) which are either not intended to produce hot water, or are intended to produce hot water either by the instantaneous or storage principle, the whole being marketed as a single unit. h) which are designed for either sealed water systems or for open water systems. This European Standard is to be used in conjunction with the General Requirements Standard EN 15502-1. For applications within the scope of the PED further requirements may be necessary (e.g. situations where the maximum allowable temperature exceeds 110 °C, or where volume times maximum allowable pressure is over 50 bar x litres). This standard provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard, the risk associated with this alternative construction shall be assessed. An example of an assessment methodology, based upon risk assessment and which covers the essential requirements of the Gas Appliance Directive, is given in Clause 11. This standard does not cover all the requirements for: i) appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex DD of EN 15502-2-1:2012); j) appliances using flue dampers; k) appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW; l) appliances of the types A, B14, B2, B3, B4, B5 and C; m) appliances intended to be connected to a (common) flue having mechanical extraction; n) appliances with gas/air ratio control; o) modular boilers; p) boilers which can give rise to condensation under certain circumstances; q) boilers intended to be installed in a room with a foreseeable negative pressure relative to the pressure in the flue system.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13836:2007(Main)
Gas fired central heating boilers - Type B boilers of nominal heat input exceeding 300 kW, but not exceeding 1 000 kW
EN 13836:2006

This European Standard specifies the requirements and test methods concerning, in particular, the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard applies to boilers of type B, as listed in 4.2:
3   that use one or more combustible gases of the three gas families at the pressures stated in Tables 16 and 17;
3   that have a nominal heat input (on the basis of net calorific value) exceeding 300 kW, but not exceeding 1  000 kW, including modular boilers;
3   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
3   where the maximum operating pressure in the water circuit does not exceed 6 bar;
3   that can give rise to condensation under certain circumstances;
3   of the standard and low-temperature types.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
This European Standard does not contain all the requirements necessary for boilers:
3   intended to be installed in the open or in living rooms;
3   permanently fitted with more than one flue outlet;
3   where the combustion circuit is sealed with respect to the room where the boiler is installed;
3   of the condensing type;
3   intended to be connected to a common flue having mechanical extraction;
3   fitted with a forced draught burner in accordance with EN 676 (see EN 303-7);
3   producing hot water for domestic purposes.
This standard only covers type testing.
Matters related to quality assurance systems, tests during production, and certificates of conformity of auxiliary devices are not dealt with in this European Standard.

  • Standard
    138 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 656:2001/A1:2006(Amendment)
Gas-fired central heating boilers - Type B boilers of nominal heat input exceeding 70 kW, but not exceeding 300 kW
EN 656:1999/A1:2006

Add to the first list of indents:
-   of the standard type possibly producing condensation in certain circumstances;
-   of the low-temperature type;"
Delete in the second list of indents:
-   of the low-temperature type;

  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 303-3:1999/AC:2006(Amendment)
Heating boilers - Part 3: Gas-fired central heating boilers - Assembly comprising a boiler body and a forced draught burner
EN 303-3:1998/AC:2006

TC - Replace Tables 5 and 6

  • Corrigendum
    7 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 303-3:1999/A2:2004(Amendment)
Heating Boilers - Part 3 : Gas-fired heating boilers - Assembly comprising a boiler body and a forced draught burner
EN 303-3:1998/A2:2004

Replace the second paragraph by the following text :
"This European Standard applies to standard boilers and low-temperature boilers with a nominal heat output not exceeding 1000 kW and with a water temperature at normal operation not exceeding 105 °C."
Replace the 2nd dash of the third paragraph by the following text :
"- condensing boilers;"
Delete the last but one paragraph of EN 303-3 :
"This European Standard does not contain all the necessary requirements for low temperature boilers. Nevertheless, the testing methods defined by this European Standard for the determination of useful efficiencies can be used for low temperature boilers, after being adapted in accordance with annex H."

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 656:2001(Main)
Gas-fired central heating boilers - Type B boilers of nominal heat input exceeding 70 kW but not exceeding 300 kW
EN 656:1999

This standard specifies the requirements and test methods concerning, in particular the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as "boilers".  This standard applies to boilers of type B, as listed in 4.2:   ? that use one or more combustible gases of the three gas families at the pressures stated in Tables 14 and 15;  ? that have a nominal heat input (net CV basis) exceeding 70 kW, but not exceeding 300 kW, including modular boilers;  ? where the temperature of the heat transfer fluid does not exceed 105 oC during normal operation;  ? where the maximum operating pressure in the water circuit does not exceed 6 bar.  The standard applies to boilers designed for sealed water systems or for open water systems.  The standard does not contain all the requirements necessary for boilers:   ? intended to be installed in the open or in living rooms;  ? permanently fitted with more than one flue outlet;  ? where the combustion circuit is sealed with respect to the room where the boiler is installed;  ? of the condensing type;  ? of the low temperature type;  ? intended to be connected to a common flue having mechanical extraction;  ? fitted with a forced draught burner in accordance with EN 676;  ? producing hot water for domestic purposes.  This standard only covers type testing.

  • Standard
    117 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 303-3:1999(Main)
Heating boilers - Part 3: Gas-fired central heating boilers - Assembly comprising a boiler body and a forced draught burner
EN 303-3:1998

This European Standard specifies the requirements and test methods for the construction, the safety and the rational energy usage of an assembly made up of a boiler body complying with EN 303- 11) and a forced draught gas burner complying with EN 676, using combustible gases, hereafter referred to as a "boiler".  This European Standard applies to a boiler:  - with a nominal output not exceeding 1 000 kW.  This European Standard does not contain all the necessary requirements for:  - assemblies designed as units;  - condensing boilers and low temperature boilers;  - boilers intended to be installed in the open;  - boilers permanently fitted with more than one flue outlet;  - boilers fitted with a draught diverter;  -  boilers intended to be connected to a common flue having mechanical    extraction.  This European Standard does not apply to living-space dedicated boilers   If the boiler body has already been tested with a liquid fuel burner, in accordance with EN 303-1, EN 303-2 and EN 304, only the tests described in annex G need to be performed.  In the case of a range of boilers, see annex F.  This European Standard does not contain all the necessary requirements for low temperature boilers. Nevertheless, the testing methods defined by this European Standard for the determination of useful efficiencies can be used for low temperature boilers, after being adapted in accordance with annex H.  This European Standard only covers type testing.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day