SIST EN 13523-17:2005

Coil coated metals - Test methods - Part 17: Adhesion of strippable films

This part of EN 13523 describes two methods for determining the numerical evaluation of the adhesion of strippable films which have previously been applied to an organic coating on a metallic substrate.
Samples can be tested irrespective of whether the strippable film has been applied in the laboratory or on the production line.
NOTE   Method 1 is preferred for films with adhesive and method 2 for films without adhesive.

Bandbeschichtete Metalle - Prüfverfahren - Teil 17: Haftfestigkeit von abziehbaren Folien

Tôles prélaquées - Méthodes d'essai - Partie 17: Adhérence des films pelables

Kovine, prevlečene v svitkih - Preskusne metode - 17. del: Oprijemljivost zaščitnih folij

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2005
• Withdrawal Date: 05-Jan-2012
• ICS: 25.220.60 - Organic coatings
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Jan-2012
• Due Date: 28-Jan-2012
• Completion Date: 06-Jan-2012
• Ref Project: EN 13523-17:2004 - Coil coated metals - Test methods - Part 17: Adhesion of strippable films

Relations

• Replaced By: SIST EN 13523-17:2012 - Coil coated metals - Test methods - Part 17: Adhesion of strippable films
• Effective Date: 01-Feb-2012
• Replaced By: SIST EN 13523-17:2012 - Coil coated metals - Test methods - Part 17: Adhesion of strippable films
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13523-17:2005
01-april-2005
.RYLQHSUHYOHþHQHYVYLWNLK3UHVNXVQHPHWRGHGHO2SULMHPOMLYRVW]DãþLWQLK
IROLM
Coil coated metals - Test methods - Part 17: Adhesion of strippable films
Bandbeschichtete Metalle - Prüfverfahren - Teil 17: Haftfestigkeit von abziehbaren Folien
Tôles prélaquées - Méthodes d'essai - Partie 17: Adhérence des films pelables
Ta slovenski standard je istoveten z: EN 13523-17:2004
ICS:
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-17:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13523-17:2005

---------------------- Page: 2 ----------------------

SIST EN 13523-17:2005
EUROPEAN STANDARD
EN 13523-17
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 25.220.60
English version
Coil coated metals - Test methods - Part 17: Adhesion of
strippable films
Tôles prélaquées - Méthodes d'essai - Partie 17: Bandbeschichtete Metalle - Prüfverfahren - Teil 17:
Adhérence des films pelables Haftfestigkeit von abziehbaren Folien
This European Standard was approved by CEN on 23 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-17:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13523-17:2005
EN 13523-17:2004 (E)
Foreword
This document (EN 13523-17:2004) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by
May 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
2

---------------------- Page: 4 ----------------------

SIST EN 13523-17:2005
EN 13523-17:2004 (E)
1 Scope
This part of EN 13523 describes two methods for determining the numerical evaluation of the adhesion of strippable
films which have previously been applied to an organic coating on a metallic substrate.
Samples can be tested irrespective of whether the strippable film has been applied in the laboratory or on the
production line.
NOTE Method 1 is preferred for films with adhesive and method 2 for films without adhesive.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.

EN 13523-0:2001, Coil coated metals — Test methods — Part 0: General introduction and list of test methods.
EN 23270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and
testing (ISO 3270:1984).
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13523-0:2001 and the following apply.
3.1
strippable film
a plastic film applied to the coated surface in order to afford a temporary protection against mechanical damage
[EN 10169-1:2003]
4 Principle
The force necessary to peel a film of given width from the surface of a coil coated material, at a defined angle and
speed, is determined using appropriate instruments.
5 Apparatus
5.1 For method 1
5.1.1 Hydraulic or electronic dynamometer with
 a movable jaw speed of (300 ± 30) mm/min
 a traction meter set so that the force required to strip the film lies between 15 % and 85 % of the measuring
scale (usually between 0 N and 10 N).
5.1.2 Cutting tool (e.g. a sharp knife)
5.1.3 Ruler
5.2 For method 2
5.2.1 Spring balance (cylinder dynamometer) with a scale of up to 10 N
3

---------------------- Page: 5 ----------------------

SIST EN 13523-17:2005
EN 13523-17:2004 (E)
5.2.2 Cutting tool (e.g. a sharp knife)
5.3.3 Ruler
6 Sampling
See EN 13523-0.
7 Test panels
See EN 13523-0.
8 Procedure
8.1 Panel preparation
8.1.1 Self-adhesive strippable film
When self-adhesive strippable film is applied in the laboratory, obs
...