SIST EN IEC 61169-65:2021

Radio-frequency connectors - Part 65: Sectional specification for RF coaxial connectors, 1,35 mm inner diameter of outer conductor, with screw-coupling, characteristic impedance 50 Ohm (IEC 61169-65:2021)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for series 1,35 mm RF coaxial connectors with
screw coupling, characteristic impedance 50 Ω, for operating frequencies up to 90 GHz.
Typical use in test and measurement applications.
It describes mating face dimensions for general purpose connectors – grade 1, dimensional
details of standard test connectors-grade 0, gauging information and tests selected from
IEC 61169-1, applicable to all detail specifications relating to series 1,35 mm RF connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference
purpose only.

Hochfrequenz-Steckverbinder – Teil 65: Rahmenspezifikation für koaxiale HF-Steckverbinder mit 1,35 mm Innendurchmesser des Außenleiters, mit Schraubkupplung, Wellenwiderstand 50 Ohm, für den Einsatz bis 90 GHz (IEC 61169-65:2021)

Connecteurs pour fréquences radioélectriques - Partie 65: Spécification intermédiaire relative aux connecteurs coaxiaux pour fréquences radioélectriques, avec un diamètre intérieur du conducteur extérieur de 1,35 mm, à couplage à vis, impédance caractéristique de 50 Ω (IEC 61169-65:2021)

IEC 61169-65:2021 fournit des informations et des règles pour l’établissement de spécifications particulières (SP) pour les connecteurs coaxiaux pour fréquences radioélectriques de série 1,35 mm à couplage à vis, avec une impédance caractéristique de 50 Ω et une fréquence de fonctionnement allant jusqu’à 90 GHz. Elle est typiquement utilisée pour des essais et des mesures.
Elle décrit les dimensions de la face d’accouplement pour les connecteurs à usage général (grade 1), les détails dimensionnels des connecteurs d’essai normalisés (grade 0), les informations de calibres et les essais choisis à partir de l’IEC 61169-1, applicables à toutes les spécifications particulières relatives aux connecteurs pour fréquences radioélectriques de série 1,35 mm.
Cette spécification indique les caractéristiques de performance recommandées à prendre en considération lors de la rédaction d’une spécification particulière et elle couvre les programmes d’essais et les exigences de contrôle pour les niveaux d’assurance M et H.

Radiofrekvenčni konektorji - 65. del: Področna specifikacija za radiofrekvenčne (RF) koaksialne konektorje z notranjim premerom 1,35 mm zunanjega prevodnika, z vijačno spojko in značilno impedanco 50 ohm (IEC 61169-65:2021)

General Information

• Status: Published
• Publication Date: 07-Mar-2021
• ICS: 33.120.30 - RF connectors
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Mar-2021
• Due Date: 10-May-2021
• Completion Date: 08-Mar-2021
• Ref Project: EN IEC 61169-65:2021 - Radio-frequency connectors - Part 65: Sectional specification for RF coaxial connectors, 1,35 mm inner diameter of outer conductor, with screw-coupling, characteristic impedance 50 Ω

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61169-65:2021
01-maj-2021
Radiofrekvenčni konektorji - 65. del: Področna specifikacija za radiofrekvenčne
(RF) koaksialne konektorje z notranjim premerom 1,35 mm zunanjega prevodnika,
z vijačno spojko in značilno impedanco 50 ohm (IEC 61169-65:2021)
Radio-frequency connectors - Part 65: Sectional specification for RF coaxial connectors,
1,35 mm inner diameter of outer conductor, with screw-coupling, characteristic
impedance 50 Ohm (IEC 61169-65:2021)
Hochfrequenz-Steckverbinder – Teil 65: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit 1,35 mm Innendurchmesser des Außenleiters, mit Schraubkupplung,
Wellenwiderstand 50 Ohm, für den Einsatz bis 90 GHz (IEC 61169-65:2021)
Connecteurs pour fréquences radioélectriques - Partie 65: Spécification intermédiaire
relative aux connecteurs coaxiaux pour fréquences radioélectriques, avec un diamètre
intérieur du conducteur extérieur de 1,35 mm, à couplage à vis, impédance
caractéristique de 50 Ω (IEC 61169-65:2021)
Ta slovenski standard je istoveten z: EN IEC 61169-65:2021
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 61169-65:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61169-65:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 61169-65:2021


EUROPEAN STANDARD EN IEC 61169-65

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2021
ICS 33.120.30

English Version
Radio-frequency connectors - Part 65: Sectional specification for
RF coaxial connectors, 1,35 mm inner diameter of outer
conductor, with screw-coupling, characteristic impedance 50 O
(IEC 61169-65:2021)
Connecteurs pour fréquences radioélectriques - Partie 65: Hochfrequenz-Steckverbinder - Teil 65:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF-Steckverbinder mit
coaxiaux pour fréquences radioélectriques, avec un 1,35 mm Innendurchmesser des Außenleiters, mit
diamètre intérieur du conducteur extérieur de 1,35 mm, à Schraubkupplung, Wellenwiderstand 50 Ohm, für den
couplage à vis, impédance caractéristique de 50 O Einsatz bis 90 GHz
(IEC 61169-65:2021) (IEC 61169-65:2021)
This European Standard was approved by CENELEC on 2021-02-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61169-65:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61169-65:2021
EN IEC 61169-65:2021 (E)
European foreword
The text of document 46F/527(F)/FDIS, future edition 1 of IEC 61169-65, prepared by SC 46F “RF
and microwave passive components” of IEC/TC 46 “Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories” was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 61169-65:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021–11–23
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–02–23
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61169-65:2021 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 61169-65:2021
EN IEC 61169-65:2021 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1:EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61726 - Cable assemblies, cables, connectors andEN 61726 -
passive microwave components -
Screening attenuation measurement by
the reverberation chamber method
IEC 62037 - RF connectors, connector cable- -
assemblies and cables - Intermodulation
level measurement
IEC 62153-4-7 - Metallic communication cable testEN 62153-4-7 -
methods - Part 4–7: Electromagnetic
compatibility (EMC) - Test method for
measuring of transfer impedance Z and
T
screening attenuation as or coupling
attenuation a of connectors and
c
assemblies up to and above 3 GHz -
Triaxial tube in tube method


3

---------------------- Page: 5 ----------------------
SIST EN IEC 61169-65:2021

---------------------- Page: 6 ----------------------
SIST EN IEC 61169-65:2021



IEC 61169-65

®


Edition 1.0 2021-01




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Radio-frequency connectors –

Part 65: Sectional specification for RF coaxial connectors, 1,35 mm inner

diameter of outer conductor, with screw-coupling, characteristic

impedance 50 Ω



Connecteurs pour fréquences radioélectriques –


Partie 65: Spécification intermédiaire relative aux connecteurs coaxiaux pour

fréquences radioélectriques, avec un diamètre intérieur du conducteur extérieur

de 1,35 mm, à couplage à vis, impédance caractéristique de 50 Ω











INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-9259-4




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61169-65:2021
– 2 – IEC 61169-65:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Mating face and gauge information . 6
4.1 Dimensions – General purpose connectors – Grade 1 . 6
4.1.1 Connector with pin centre contact . 6
4.1.2 General purpose connector with socket centre contact . 7
4.2 Gauge pin for socket centre contact . 8
4.2.1 Dimensions . 8
4.2.2 Test procedure . 8
4.3 Dimensions standard test connectors – Grade 0 . 8
4.3.1 Standard test connector with pin centre contact . 8
4.3.2 Standard test connector with socket centre contact . 9
5 Quality assessment procedures . 11
5.1 General . 11
5.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) . 11
5.3 Test schedule and inspection requirements. 12
5.3.1 Acceptance tests . 12
5.3.2 Periodic tests . 13
5.4 Procedures for quality conformance . 15
5.4.1 Quality conformance inspection . 15
5.4.2 Quality conformance and its maintenance . 15
6 Instructions for preparation of detail specifications . 15
6.1 General . 15
6.2 Identification of the component . 15
6.3 Performance . 15
6.4 Marking, ordering information and related matters . 16
6.5 Selection of tests, test conditions and severities . 16
6.6 Blank detail specification pro-forma for 1,35 mm connectors . 16

Figure 1 – General purpose connector with pin centre contact . 6
Figure 2 – General purpose connector with socket centre contact . 7
Figure 3 – Gauge pin for socket centre contact . 8
Figure 4 – Standard test connector with pin centre contact . 9
Figure 5 – Standard test connector with socket centre contact . 10

Table 1 – Dimensions of connector with pin centre contact – Grade 1 . 6
Table 2 – Dimensions of connector with socket centre contact – Grade 1 . 7
Table 3 – Dimensions of gauge pin for socket centre contact . 8
Table 4 – Dimensions of connector with pin centre contact – Grade 0 . 9
Table 5 – Dimensions of connector with socket centre contact – Grade 0 . 10
Table 6 – Ratings and characteristics . 11
Table 7 – Acceptance tests . 12
Table 8 – Periodic tests . 13

---------------------- Page: 8 ----------------------
SIST EN IEC 61169-65:2021
IEC 61169-65:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 65: Sectional specification for RF coaxial connectors,
1,35 mm inner diameter of outer conductor, with screw-coupling,
characteristic impedance 50 Ω

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-65 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories.
The text of this International Standard is based on the following documents:
FDIS Report on voting
46F/527/FDIS 46F/542/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.

---------------------- Page: 9 ----------------------
SIST EN IEC 61169-65:2021
– 4 – IEC 61169-65:2021 © IEC 2021
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------
SIST EN IEC 61169-65:2021
IEC 61169-65:2021 © IEC 2021 – 5 –
RADIO-FREQUENCY CONNECTORS –

Part 65: Sectional specification for RF coaxial connectors,
1,35 mm inner diameter of outer conductor, with screw-coupling,
characteristic impedance 50 Ω


1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for series 1,35 mm RF coaxial connectors with
screw coupling, characteristic impedance 50 Ω, for operating frequencies up to 90 GHz.
Typical use in test and measurement applications.
It describes mating face dimensions for general purpose connectors – grade 1, dimensional
details of standard test connectors-grade 0, gauging information and tests selected from
IEC 61169-1, applicable to all detail specifications relating to series 1,35 mm RF connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference
purpose only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 61726, Cable assemblies, cables, connectors and passive microwave components –
Screening attenuation measurement by the reverberation chamber method
IEC 62037, Passive RF and microwave devices, intermodulation level measurement
IEC 62153-4-7, Metallic communication cables test methods – Part 4-7: Electromagnetic
compatibility (EMC) – Test method for measuring of transfer impedance ZT and screening
attenuation a or coupling attenuation a of connectors and assemblies up to and above
s c
3 GHz – Triaxial tube in tube method
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp

---------------------- Page: 11 ----------------------
SIST EN IEC 61169-65:2021
– 6 – IEC 61169-65:2021 © IEC 2021
4 Mating face and gauge information
4.1 Dimensions – General purpose connectors – Grade 1
4.1.1 Connector with pin centre contact
The mating face of connector with pin centre contact is shown in Figure 1 and the dimensions
are given in Table 1.

Figure 1 – General purpose connector with pin centre contact
Table 1 – Dimensions of connector with pin centre contact – Grade 1
mm (°)
Ref. Remarks
Min. Max.

a 3,700 4,000

b 1,600 2,100

c
0,300 0,500
d 3,450 3,490 Diameter
e M5,5x0,5-6H Thread
f 5,700 5,800 Diameter
g 0,576 0,596 Diameter
h 1,335 1,365 Diameter
j 0,200 0,250 Chamfer

k
2,600 2,700
l 0,100 0,150 Diameter
m 0,274 0,300 Diameter
n
0,003 0,050

o 0,900 1,100

p 30° nom.
q 0,000 0,030 Radius
r 0,000 0,300 Radius
NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Spanner flat size 8, alternatively flat size 7 or ¼” for special applications.
NOTE 3 Surface roughness Ra < 0,4 µm.

---------------------- Page: 12 ----------------------
SIST EN IEC 61169-65:2021
IEC 61169-65:2021 © IEC 2021 – 7 –
4.1.2 General purpose connector with socket centre contact
The mating face of connector with socket centre contact is shown in Figure 2 and it
...