SIST EN IEC 61169-1-9:2025
(Main)Radio-frequency connectors- Part 1-9: Mechanical test methods- Safety wire hole pull-out (IEC 61169-1-9:2025)
Radio-frequency connectors- Part 1-9: Mechanical test methods- Safety wire hole pull-out (IEC 61169-1-9:2025)
IEC 61169-1-9:2025 specifies test methods for the safety wire hole pull-out of RF connectors.
This document is applicable to the connectors with safety wire holes.
Hochfrequenz-Steckverbinder - Teil 1-9: Mechanische Prüfverfahren - Herausziehen von Sicherheitsdrahtlöchern (IEC 61169-1-9:2025)
Connecteurs pour fréquences radioélectriques - Partie 1-9: Méthodes d’essais mécaniques - Extraction par le trou du fil de sécurité (IEC 61169-1-9:2025)
L'IEC 61169-1-9:2025 spécifie les méthodes d'essai relatives à l’extraction par le trou du fil de sécurité des connecteurs RF.
Ce document est applicable aux connecteurs comportant des trous pour les fils de sécurité.
Radiofrekvenčni konektorji - 1-9. del: Mehanske preskusne metode - Izvlečna luknja za varnostno žico (IEC 61169-1-9:2025)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2025
Radiofrekvenčni konektorji - 1-9. del: Mehanske preskusne metode - Izvlečna
luknja za varnostno žico (IEC 61169-1-9:2025)
Radio-frequency connectors- Part 1-9: Mechanical test methods- Safety wire hole pull-
out (IEC 61169-1-9:2025)
Hochfrequenz-Steckverbinder - Teil 1-9: Mechanische Prüfverfahren - Herausziehen von
Sicherheitsdrahtlöchern (IEC 61169-1-9:2025)
Connecteurs pour fréquences radioélectriques - Partie 1-9: Méthodes d’essais
mécaniques - Extraction par le trou du fil de sécurité (IEC 61169-1-9:2025)
Ta slovenski standard je istoveten z: EN IEC 61169-1-9:2025
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61169-1-9
NORME EUROPÉENNE
EUROPÄISCHE NORM June 2025
ICS 33.120.30
English Version
Radio-frequency connectors - Part 1-9: Mechanical test methods
- Safety wire hole pull-out
(IEC 61169-1-9:2025)
Connecteurs pour fréquences radioélectriques - Partie 1-9: Hochfrequenz-Steckverbinder - Teil 1-9: Mechanische
Méthodes d'essais mécaniques - Extraction par le trou du fil Prüfverfahren - Herausziehen von Sicherheitsdrahtlöchern
de sécurité (IEC 61169-1-9:2025)
(IEC 61169-1-9:2025)
This European Standard was approved by CENELEC on 2025-06-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-1-9:2025 E
European foreword
The text of document 46F/701/FDIS, future edition 1 of IEC 61169-1-9, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-1-9:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-06-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-06-30
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61169-1-9:2025 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 - Radio frequency connectors - Part 1: EN 61169-1 -
Generic specification - General
requirements and measuring methods
IEC 61169-1-9 ®
Edition 1.0 2025-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Radio-frequency connectors –
Part 1-9: Mechanical test methods – Safety wire hole pull-out
Connecteurs pour fréquences radioélectriques –
Partie 1-9: Méthodes d’essais mécaniques – Extraction par le trou du fil de
sécurité
ICS 33.120.30 ISBN 978-2-8327-0417-2
IEC 61169-1-9:2025-05(en-fr)
– 2 – IEC 61169-1-9:2025 © IEC 2025
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Test equipment. 5
5 Test conditions . 5
6 Test procedure . 5
7 Information to be given in the relevant specification . 6
8 Test report . 7
Annex A (informative) Position of safety wire hole and selection of safety wire . 8
A.1 Safety wire hole . 8
A.2 Selection of safety wire . 8
A.3 Installation of safety wire . 9
Figure 1 – Pulling force direction of safety wire hole. 6
Figure A.1 – Position of safety wire hole . 8
Figure A.2 – Procedure of installing safety wire . 9
Table A.1 – Recommended safety wire size . 8
IEC 61169-1-9:2025 © IEC 2025 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 1-9: Mechanical test methods – Safety wire hole pull-out
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.