SIST EN 60974-11:2010
Arc welding equipment - Part 11: Electrode holders (IEC 60974-11:2010)
Arc welding equipment - Part 11: Electrode holders (IEC 60974-11:2010)
This part of IEC 60974 is applicable to electrode holders for manual metal arc welding with electrodes up to 10 mm in diameter. It is not applicable to electrode holders for underwater welding. This part of IEC 60974 specifies safety and performance requirements of electrode holders.
Lichtbogenschweißeinrichtungen - Teil 11: Elektrodenhalter (IEC 60974-11:2010)
Matériel de soudage à l'arc - Partie 11: Porte-électrodes (CEI 60974-11:2010)
La CEI 60974-11:2010 s'applique aux porte-électrode pour soudage manuel électrique à l'arc avec des électrodes jusqu'à 10 mm de diamètre. Elle ne s'applique pas aux porte-électrode pour le soudage sous l'eau. La présente partie de la CEI 60974 spécifie les exigences de sécurité et de performance pour les porte-électrode. Cette troisième édition annule et remplace la deuxième édition parue en 2004. Elle constitue une révision technique. Les modifications signifiantes concernant l'édition précédente sont les suivantes: - modification des conditions ambiantes conformément à la CEI 60974-1 (voir l'Article 4); - modification de la précision des appareils de mesure électriques à la Classe 1 (voir 5.1); - correction du diamètre de bille à 12,5 mm (voir 8.1); - autre essai de rigidité diélectrique (voir 8.3). Cette publication doit être lue conjointement avec la CEI 60974-1:2005.
Oprema za obločno varjenje - 11. del: Držala elektrod (IEC 60974-11:2010)
Ta del IEC 60974 velja za držala elektrod za ročno kovinsko opremo za obločno varjenje, z elektrodami premera do 10 mm. Ne velja za držala elektrod za podvodno varjenje. Ta del IEC 60974 določa zahteve za varnost in delovanje držal elektrod.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60974-11:2010
01-december-2010
1DGRPHãþD
SIST EN 60974-11:2005
2SUHPD]DREORþQRYDUMHQMHGHO 'UåDODHOHNWURG ,(&
Arc welding equipment - Part 11: Electrode holders (IEC 60974-11:2010)
Lichtbogenschweißeinrichtungen - Teil 11: Elektrodenhalter (IEC 60974-11:2010)
Matériel de soudage à l'arc - Partie 11: Porte-électrodes (CEI 60974-11:2010)
Ta slovenski standard je istoveten z: EN 60974-11:2010
ICS:
25.160.30 Varilna oprema Welding equipment
SIST EN 60974-11:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60974-11:2010
---------------------- Page: 2 ----------------------
SIST EN 60974-11:2010
EUROPEAN STANDARD
EN 60974-11
NORME EUROPÉENNE
October 2010
EUROPÄISCHE NORM
ICS 25.160 Supersedes EN 60974-11:2004
English version
Arc welding equipment -
Part 11: Electrode holders
(IEC 60974-11:2010)
Matériel de soudage à l'arc - Lichtbogenschweißeinrichtungen -
Partie 11: Porte-électrodes Teil 11: Elektrodenhalter
(CEI 60974-11:2010) (IEC 60974-11:2010)
This European Standard was approved by CENELEC on 2010-10-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60974-11:2010 E
---------------------- Page: 3 ----------------------
SIST EN 60974-11:2010
EN 60974-11:2010 - 2 -
Foreword
The text of document 26/421/FDIS, future edition 3 of IEC 60974-11, prepared by IEC TC 26, Electric
welding, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60974-11 on 2010-10-01.
This European Standard supersedes EN 60974-11:2004.
The significant changes with respect to EN 60974-11:2004 are the following:
– change of the environmental condition in accordance with EN 60974-1 (see Clause 4);
– change of electrical measuring instruments accuracy to Class 1 (see 5.1);
– correction of sphere diameter to 12,5 mm (see 8.1);
– alternative dielectric strength test (see 8.3).
This standard is to be used in conjunction with EN 60974-1.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-10-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60974-11:2010 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 4 ----------------------
SIST EN 60974-11:2010
- 3 - EN 60974-11:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60050-151 - International Electrotechnical Vocabulary - -
(IEV) -
Part 151: Electrical and magnetic devices
IEC 60529 - Degrees of protection provided by enclosures EN 60529 -
(IP Code)
IEC 60974-1 - Arc welding equipment - EN 60974-1 -
Part 1: Welding power sources
---------------------- Page: 5 ----------------------
SIST EN 60974-11:2010
---------------------- Page: 6 ----------------------
SIST EN 60974-11:2010
IEC 60974-11
®
Edition 3.0 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Arc welding equipment –
Part 11: Electrode holders
Matériel de soudage à l’arc –
Partie 11: Porte-électrodes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
M
CODE PRIX
ICS 25.160 ISBN 978-2-88912-103-8
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60974-11:2010
– 2 – 60974-11 © IEC:2010
CONTENTS
FOREWORD.3
1 Scope.5
2 Normative references .5
3 Terms and definitions .5
4 Environmental conditions.6
5 Type tests .6
5.1 Test conditions.6
5.2 Tests sequence .6
6 Designation .7
7 Operation .7
8 Protection against electric shock .7
8.1 Protection against direct contact .7
8.2 Insulation resistance .8
8.3 Dielectric strength .8
9 Thermal rating .9
9.1 Temperature rise.9
9.2 Resistance to heat .9
9.3 Resistance to hot objects .10
10 Mechanical requirements.10
10.1 Welding cable entry.10
10.2 Penetration of the welding cable insulation.10
10.3 Welding cable connection.11
10.4 Impact resistance .11
11 Marking .12
12 Instructions for use.12
Figure 1 – Arrangement for the temperature rise test .9
Figure 2 – Device for testing the resistance to hot objects .10
Figure 3 – Device for the pendulum swing test.12
7
Table 1 – Dimensional requirements for the electrode holder .
---------------------- Page: 8 ----------------------
SIST EN 60974-11:2010
60974-11 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ARC WELDING EQUIPMENT –
Part 11: Electrode holders
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60974-11 has been prepared by IEC technical committee 26:
Electric welding.
This third edition cancels and replaces the second edition published in 2004. This edition
constitutes a technical revision.
The significant changes with respect to the previous edition are the following:
– change of the environmental condition in accordance with IEC 60974-1 (see Clause 4);
– change of electrical measuring instruments accuracy to Class 1 (see 5.1);
– correction of sphere diameter to 12,5 mm (see 8.1);
– alternative dielectric strength test (see 8. 3 ) .
This part of IEC 60974 is to be used in conjunction with IEC 60974-1.
---------------------- Page: 9 ----------------------
SIST EN 60974-11:2010
– 4 – 60974-11 © IEC:2010
The text of this standard is based on the following documents:
FDIS Report on voting
26/421/FDIS 26/427/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 60974 series, published under the general title Arc welding
equipment, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
SIST EN 60974-11:2010
60974-11 © IEC:2010 – 5 –
ARC WELDING EQUIPMENT –
Part 11: Electrode holders
1 Scope
This part of IEC 60974 is applicable to electrode holders for manual metal arc welding with
electrodes up to 10 mm in diameter.
It is not applicable to electrode holders for underwater welding.
This part of IEC 60974 specifies safety and performance requirements of electrode holders.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60050-151, International Electrotechnical Vocabulary – Part 151: Electrical and magnetic
devices
IEC 60529, Degrees of protection provided by enclosures (IP Code)
IEC 60974-1, Arc welding equipment - Part 1: Welding power sources
3 Terms and definitions
For the purpose of this document, the terms and definitions contained in IEC 60050-151 and
IEC 60974-1, as well as the following apply.
3.1
electrode holder
insulated tool
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.