SIST EN ISO 13628-1:2025

Oil and gas industries including low carbon energy - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2025)

ISO 13628-1:2005 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment. ISO 13628-1:2005 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard. The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells. ISO 13628-1:2005 and its related subsystem standards apply as far as the interface limits described in Clause 4. Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.

Öl- und Gasindustrie einschließlich kohlenstoffarmer Energieträger - Auslegung und Betrieb von Unterwasser-Fördersystemen - Teil 1: Allgemeine Anforderungen und Empfehlungen (ISO 13628-1:2025)

Industries du pétrole et du gaz, y compris les énergies à faible teneur en carbone - Conception et exploitation des systèmes de production immergés - Partie 1: Exigences générales et recommandations (ISO 13628-1:2025)

L'ISO 13628-1:2005 fournit des exigences générales et des recommandations pour le développement de systèmes de production immergés complets, de la phase de conception jusqu'au démantèlement et à l'abandon. L'ISO 13628-1:2005 est un document cadre régissant les autres parties de l'ISO 13628 qui traitent de manière plus détaillée des exigences relatives aux sous-systèmes faisant généralement partie d'un système de production immergé. Néanmoins, dans certains domaines (par exemple, conception du système, structures, manifolds, dispositifs de levage, couleur et marquage), des exigences plus détaillées sont incluses dans la présente norme, car ces sujets ne sont pas couverts par une norme de sous-système. Le système de production immergé complet comprend plusieurs sous-systèmes nécessaires pour produire des hydrocarbures à partir d'un ou plusieurs puits sous-marins et les transférer vers une installation de traitement donnée située en mer (fixe, flottante ou immergée) ou à terre, ou pour injecter de l'eau/du gaz dans les puits sous-marins. L'ISO 13628-1:2005 et les normes de sous-systèmes connexes, s'appliquent jusqu'aux limites d'interface décrites à l'Article 4. Les équipements spéciaux, tels que les «split trees», les têtes de production et les manifolds des chambres atmosphériques, ne sont pas spécifiquement décrits du fait de leur usage limité. Toutefois, les informations fournies sont applicables à ces types d'équipement.

Naftna in plinska industrija, vključno z nizkoogljično energijo - Načrtovanje in upravljanje proizvodnje v podmorskih sistemih - 1. del: Splošne zahteve in priporočila (ISO 13628-1:2025)

General Information

• Status: Published
• Public Enquiry End Date: 26-Feb-2024
• Publication Date: 26-Feb-2025
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 19-Feb-2025
• Due Date: 26-Apr-2025
• Completion Date: 27-Feb-2025
• Ref Project: EN ISO 13628-1:2025 - Oil and gas industries including low carbon energy - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2025)

Relations

• Revises: SIST EN ISO 13628-1:2006/A1:2014 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations - Amendment 1: Revised Clause 6 (ISO 13628-1:2005/Amd 1:2010)
• Effective Date: 11-Oct-2023
• Revises: SIST EN ISO 13628-1:2006 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2005)
• Effective Date: 11-Oct-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2025
Naftna in plinska industrija, vključno z nizkoogljično energijo - Načrtovanje in
upravljanje proizvodnje v podmorskih sistemih - 1. del: Splošne zahteve in
priporočila (ISO 13628-1:2025)
Oil and gas industries including low carbon energy - Design and operation of subsea
production systems - Part 1: General requirements and recommendations (ISO 13628-
1:2025)
Öl- und Gasindustrie einschließlich kohlenstoffarmer Energieträger - Auslegung und
Betrieb von Unterwasser-Fördersystemen - Teil 1: Allgemeine Anforderungen und
Empfehlungen (ISO 13628-1:2025)
Industries du pétrole et du gaz, y compris les énergies à faible teneur en carbone -
Conception et exploitation des systèmes de production immergés - Partie 1: Exigences
générales et recommandations (ISO 13628-1:2025)
Ta slovenski standard je istoveten z: EN ISO 13628-1:2025
ICS:
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 13628-1
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2025
EUROPÄISCHE NORM
ICS 75.180.10 Supersedes EN ISO 13628-1:2005, EN ISO 13628-
1:2005/A1:2010
English Version
Oil and gas industries including low carbon energy -
Design and operation of subsea production systems - Part
1: General requirements and recommendations (ISO
13628-1:2025)
Industries du pétrole et du gaz, y compris les énergies Öl- und Gasindustrie einschließlich kohlenstoffarmer
à faible teneur en carbone - Conception et exploitation Energieträger - Auslegung und Betrieb von
des systèmes de production immergés - Partie 1: Unterwasser-Fördersystemen - Teil 1: Allgemeine
Exigences générales et recommandations (ISO 13628- Anforderungen und Empfehlungen (ISO 13628-
1:2025) 1:2025)
This European Standard was approved by CEN on 29 March 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13628-1:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 13628-1:2025) has been prepared by Technical Committee ISO/TC 67 "Oil and
gas industries including lower carbon energy" in collaboration with Technical Committee CEN/TC 12
“Oil and gas industries including lower carbon energy” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2025, and conflicting national standards shall
be withdrawn at the latest by August 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13628-1:2005, EN ISO 13628-1:2005/A1:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13628-1:2025 has been approved by CEN as EN ISO 13628-1:2025 without any
modification.
International
Standard
ISO 13628-1
Third edition
Oil and gas industries including
2025-01
low carbon energy — Design and
operation of subsea production
systems —
Part 1:
General requirements and
recommendations
Industries du pétrole et du gaz, y compris les énergies à faible
teneur en carbone — Conception et exploitation des systèmes de
production immergés —
Partie 1: Exigences générales et recommandations
Reference number
ISO 13628-1:2025(en) © ISO 2025

ISO 13628-1:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 13628-1:2025(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
3.1 Terms and definitions .1
3.2 Abbreviated terms .3
4 Subsea production system . 4
4.1 General .4
4.2 System configuration .4
4.3 Overview of API 17 series documents by categories .5
4.3.1 System level documents . .5
4.3.2 Subsea hardware (wellheads, trees, manifolds, structures, connectors, and
pumps) .6
4.3.3 Flowlines and risers .7
4.3.4 Control systems .7
4.3.5 Intervention systems .8
5 Systems engineering . 8
5.1 General .8
5.2 Systems engineering process .9
5.3 Subsea system production assurance and reliability management .10
6 Equipment design requirements .11
6.1 Design basis.11
6.2 Safety.11
6.2.1 General .11
6.2.2 Safety strategy . 12
6.2.3 Safety by design . 12
6.3 Barrier and isolation considerations . 12
6.3.1 Barrier philosophy . 12
6.3.2 Barrier requirements .14
6.3.3 Subsea isolation philosophy .14
6.4 Materials . 15
6.5 Structural analysis .16
6.5.1 General .16
6.5.2 Wellhead, tree, and C/WO riser system analysis .16
6.6 Pumps, piping, and valves .16
6.7 Dropped objects and fishing gear loads .17
6.8 Lifting components, padeyes, and unpressurized structural components .17
6.9 Colours and marking .17
6.10 Tolerance evaluation .
...