SIST EN ISO 217:2013
(Main)Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction (ISO 217:2013)
Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction (ISO 217:2013)
This International Standard specifies a primary range and a supplementary range of untrimmed sizes of paper in sheets which are to be trimmed to the ISO-A series of sizes as given in ISO 216, and establishes a system of designation of untrimmed sizes. This International Standard also specifies the method for the indication of machine direction of untrimmed sizes.
Papier - Rohformate - Kennzeichnung und Toleranzen für die Grund- und Ergänzungsreihen, Angabe der Maschinenlaufrichtung (ISO 217:2013)
Diese Internationale Norm legt eine Grundreihe und eine Ergänzungsreihe für Rohformate für Bogen fest, die auf die in ISO 216 festgelegten Formate beschnitten werden sollen. Darüber hinaus wird ein System zur Kennzeichnung von Rohformaten eingefügt.
Weiterhin legt diese Internationale Norm ein System für die Angabe der Maschinenlaufrichtung von Roh-formaten fest.
Papier - Formats bruts - Désignation et tolérances pour la série principale et la série auxiliaire, et désignation du sens machine (ISO 217:2013)
L'ISO 217:2013 spécifie une série principale et une série auxiliaire de formats bruts de papier en feuilles destinés à être découpés aux formats indiqués dans l'ISO 216, et établit un système de désignation des formats bruts.
Elle spécifie également la méthode permettant d'indiquer le sens machine des formats bruts.
Papir - Neobrezane pole - Označevanje in dovoljena odstopanja za osnovne in dopolnilne formate ter navedba vzdolžne smeri vlaken v papirju (MD) (ISO 217:2013)
Ta mednarodni standard določa osnovni in dopolnilni format za neobrezane pole listov papirja, ki morajo biti obrezane glede na vrsto pol ISO-A, kot je navedeno v standardu ISO 216, ter vzpostavlja sistem označevanja neobrezanih pol. Ta mednarodni standard določa tudi metodo za navajanje smeri neobrezanih pol v stroju.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 217:2013
01-oktober-2013
1DGRPHãþD
SIST EN ISO 217:2008
3DSLU1HREUH]DQHSROH2]QDþHYDQMHLQGRYROMHQDRGVWRSDQMD]DRVQRYQHLQ
GRSROQLOQHIRUPDWHWHUQDYHGEDY]GROåQHVPHULYODNHQYSDSLUMX 0' ,62
Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary
ranges, and indication of machine direction (ISO 217:2013)
Papier - Rohformate - Kennzeichnung und Toleranzen für die Grund- und
Ergänzungsreihen, Angabe der Maschinenlaufrichtung (ISO 217:2013)
Papier - Formats bruts - Désignation et tolérances pour la série principale et la série
auxiliaire, et désignation du sens machine (ISO 217:2013)
Ta slovenski standard je istoveten z: EN ISO 217:2013
ICS:
85.060 Papir, karton in lepenka Paper and board
SIST EN ISO 217:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 217:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 217:2013
EUROPEAN STANDARD
EN ISO 217
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2013
ICS 85.060 Supersedes EN ISO 217:2008
English Version
Paper - Untrimmed sizes - Designation and tolerances for
primary and supplementary ranges, and indication of machine
direction (ISO 217:2013)
Papier - Formats bruts - Désignation et tolérances pour la Papier - Rohformate - Kennzeichnung und Toleranzen für
série principale et la série auxiliaire, et désignation du sens die Grund- und Ergänzungsreihen, Angabe der
machine (ISO 217:2013) Maschinenlaufrichtung (ISO 217:2013)
This European Standard was approved by CEN on 22 June 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 217:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 217:2013
EN ISO 217:2013 (E)
Contents
Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 217:2013
EN ISO 217:2013 (E)
Foreword
This document (EN ISO 217:2013) has been prepared by Technical Committee ISO/TC 6 “Paper, board and
pulps” in collaboration with Technical Committee CEN/TC 172 “Pulp, paper and board” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at
the latest by January 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 217:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 217:2013 has been approved by CEN as EN ISO 217:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 217:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 217:2013
INTERNATIONAL ISO
STANDARD 217
Fourth edition
2013-07-15
Paper — Untrimmed sizes —
Designation and tolerances for
primary and supplementary ranges,
and indication of machine direction
Papier — Formats bruts — Désignation et tolérances pour la série
principale et la série auxiliaire, et désignation du sens machine
Reference number
ISO 217:2013(E)
©
ISO 2013
---------------------- Page: 7 ----------------------
SIST EN ISO 217:2013
ISO 217:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 217:2013
ISO 217:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation of size and machine direction . 2
5 Size of standard untrimmed sheets and identification of machine direction .3
5.1 Primary range (R). 3
5.2 Supplementary range (SR) . 3
6 Tolerances .
...
SLOVENSKI STANDARD
kSIST FprEN ISO 217:2013
01-april-2013
3DSLU1HREUH]DQHSROH2]QDþHYDQMHLQGRYROMHQDRGVWRSDQMD]DRVQRYQHLQ
GRSROQLOQHIRUPDWHWHUQDYHGEDVPHULYVWURMX ,62)',6
Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary
ranges, and indication of machine direction (ISO/FDIS 217:2013)
Papier - Rohformate - Kennzeichnung und Toleranzen für die Grund- und
Ergänzungsreihen, Angabe der Maschinenlaufrichtung (ISO/FDIS 217:2013)
Papier - Formats bruts - Désignation et tolérances pour la série principale et la série
auxiliaire, et désignation du sens machine (ISO/FDIS 217:2013)
Ta slovenski standard je istoveten z: FprEN ISO 217
ICS:
85.060 Papir, karton in lepenka Paper and board
kSIST FprEN ISO 217:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 217:2013
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 217:2013
EUROPEAN STANDARD
FINAL DRAFT
FprEN ISO 217
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2013
ICS 85.060 Will supersede EN ISO 217:2008
English Version
Paper - Untrimmed sizes - Designation and tolerances for
primary and supplementary ranges, and indication of machine
direction (ISO/FDIS 217:2013)
Papier - Formats bruts - Désignation et tolérances pour la Papier - Rohformate - Kennzeichnung und Toleranzen für
série principale et la série auxiliaire, et désignation du sens die Grund- und Ergänzungsreihen, Angabe der
machine (ISO/FDIS 217:2013) Maschinenlaufrichtung (ISO/FDIS 217:2013)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 172.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprEN ISO 217:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 217:2013
FprEN ISO 217:2013 (E)
Contents
Page
Foreword .3
2
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 217:2013
FprEN ISO 217:2013 (E)
Foreword
This document (prEN ISO 217:2013) has been prepared by Technical Committee ISO/TC 6 “Paper, board and
pulps” in collaboration with Technical Committee CEN/TC 172 “Pulp, paper and board” the secretariat of
which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document will supersede EN ISO 217:2008.
Endorsement notice
The text of ISO/FDIS 217:2013 has been approved by CEN as FprEN ISO 217:2013 without any modification.
3
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 217:2013
---------------------- Page: 6 ----------------------
kSIST FprEN ISO 217:2013
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 217
ISO/TC 6
Paper — Untrimmed sizes —
Secretariat: SCC
Designation and tolerances for
Voting begins on:
2013-02-21 primary and supplementary ranges,
and indication of machine direction
Voting terminates on:
2013-04-21
Papier — Formats bruts — Désignation et tolérances pour la série
principale et la série auxiliaire, et désignation du sens machine
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 217:2013(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2013
---------------------- Page: 7 ----------------------
kSIST FprEN ISO 217:2013
ISO/FDIS 217:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
kSIST FprEN ISO 217:2013
ISO/FDIS 217:2013(E)
ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the International Organization for Standardization (ISO), and pro
cessed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. The final draft was
established on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
twomonth approval vote in ISO and formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
© ISO 2013 – All rights reserved iii
---------------------- Page: 9 ----------------------
kSIST FprEN ISO 217:2013
ISO/FDIS 217:2013(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation of size and machine direction . 2
5 Size of standard untrimmed sheets and identification of machine direction .3
5.1 Primary range (R). 3
5.2 Supplementary range (SR) .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.