SIST EN 12697-21:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
This European Standard describes a test method for measuring the indentation of mastic asphalt when it is penetrated at a given temperature, load and for a fixed time period by a standardised cylindrical indentor pin with a circular flat-ended base. This European Standard applies to mastic asphalt with aggregates of maximum nominal size less or equal to 16 mm.
Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an Platten
Die vorliegende Europäische Norm beschreibt ein Prüfverfahren zur Messung der Eindringtiefe in Guss-asphalt, wenn bei einer festgelegten Temperatur, einer festgelegten Beanspruchung und für eine bestimmte Zeit ein genormter zylindrischer Prüfstempel mit einer kreisrunden flachen Grundfläche in diesen Asphalt eindringt. Diese Europäische Norm gilt für Gussasphalt mit einer maximalen Nennkorngröße von 16 mm oder weniger.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 21: Essai d'indentation de plaques
La présente Norme européenne décrit une méthode de mesure de l'indentation d'un asphalte coulé lorsqu'il est soumis a la pénétration d'un poinçon normalisé cylindrique avec un embout plat circulaire, a des valeurs données de température et de charge et pour un temps d'application fixé. Cette Norme européenne s'applique a des asphaltes coulés dont la dimension nominale maximale est inférieure ou égale a 16 mm.
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 21. del: Preskus z vtiskanjem na plošče
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an PlattenMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 21: Essai d'indentation de plaquesBituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-21:2003SIST EN 12697-21:2004en01-junij-2004SIST EN 12697-21:2004SLOVENSKI
STANDARD
SIST EN 12697-21:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-21November 2003ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part21: Indentation using plate specimensMélanges bitumineux - Méthodes d'essai pour enrobés àchaud - Partie 21: Essai d'indentation de plaguesAsphalt - Prüfverfahren für Heißasphalt - Teil 21:Eindringversuch an PlattenThis European Standard was approved by CEN on 1 September 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-21:2003 ESIST EN 12697-21:2004
EN 12697-21:2003 (E)2ContentsPageForeword.31Scope.62Normative references.63Apparatus.63.1Moulding of test cubes of mastic asphalt.63.2Apparatus for the indentation test.64Sampling and preparation of laboratory sample.74.1Sampling.74.2Preparation of the samples.75Procedure.76Calculation and expression of results.87Precision.98Test report.9Bibliography.10SIST EN 12697-21:2004
EN 12697-21:2003 (E)3ForewordThis document (EN 12697-21:2003) has been prepared by Technical Committee CEN/TC 227 “Roadmaterials”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by May 2004, and conflicting national standards shall be withdrawn at thelatest by August 2005.This European Standard is one of a series of standards as listed below:EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content.EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle sizedistribution.EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotaryevaporator.EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bintumen recovery:Fractionating column.EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of themaximum density.EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk densityof bituminous specimens.EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk densityof bituminous specimens by gamma rays.EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of voidcharacteristics of bituminous specimens.EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of thereference density.EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility.prEN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of theaffinity between aggregate and bitumen.EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the watersensitivity of bituminous specimens.EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperaturemeasurement.EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content.EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of thesegregation sensitivity.SIST EN 12697-21:2004
EN 12697-21:2003 (E)4prEN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studdedtyres.prEN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porousasphalt specimen.prEN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage fromporous asphalt.prEN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability ofspecimen.prEN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cubeor Marshall specimens.EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using platespecimens.prEN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking.EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of theindirect tensile strength of bituminous specimens.prEN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue.prEN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test.prEN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness.EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling.EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples fordetermining binder content, water content and grading.EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of thedimensions of bituminous specimen.prEN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation,impact compactor.prEN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparationgyratory compactor.EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction ofbituminous mixtures by vibratory compactor.prEN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared byroller compactor.prEN 12697-34, Bituminous mixtures — Test methods for h
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.