SIST EN ISO 11200:1997
(Main)Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and other specified positions (ISO 11200:1995)
Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and other specified positions (ISO 11200:1995)
The International Standard provides brief summaries of the basic International Standards for determining emission sound pressure levels from all types of machinery and equipment, at work stations and at other specified positions, and gives guidelines on the process of selection of which is appropriate to any particular type. The guidance given applies only to airborne sound, and is for use in the preparation of noise test codes, and also for use in noise testing where no code exists. It is important that specific noise test codes for various types of machinery and equipment be established and used in accordance with the requirements of these basic International Standards. Such standardized noise test codes will give detailed requirements on mounting and operating conditions for the particular family to which the machine under test belongs, as well as the location of the work station(s) and other specified positions as prescribed in these International Standards. The data so obtained may also be used for the declaration and verification of emission sound pressure levels as specified in ISO 4871. Note: At any given position in relation to a particular machine, and for given mounting and operating conditions, the emission sound pressure levels determined by any of the methods given in ISO 11201 to ISO 11204 will in general be lower than the directly measured sound pressure levels for the same machine in the typical workroom where it is used. This is due to reverberation and the contributions of other machines. A method of calculating the sound pressure levels in the vicinity of a machine operating alone in a workroom is given in ISO 11690-3. Commonly observed differences are 1 dB to 5 dB, but in extreme cases the difference may be even greater.
Akustik - Geräuschabstrahlung von Maschinen und Geräten - Leitlinien zur Anwendung der Grundnormen zur Bestimmung von Emissions-Schalldruckpegeln am Arbeitsplatz und an anderen festgelegten Orten (ISO 11200:1995)
Diese Internationale Norm enthält Kurzbeschreibungen der Internationalen Grundnormen zur Bestimmung der Emissions-Schalldruckpegel an Arbeitsplätzen und an anderen festgelegten Orten von allen Maschinen- und Gerätearten, und sie gibt Hinweise zur Auswahl einer dieser Normen, die für eine bestimmte Art geeignet ist. Die Hinweise gelten nur für Luftschall und dienen zur Verwendung bei der Erstellung von maschinenspezifischen Geräuschmeßnormen sowie zur Geräuschmessung, falls keine maschinenspezifische Geräuschmeßnorm existiert.
Acoustique - Bruit émis par les machines et équipements - Guide d'utilisation des normes de base pour la détermination des niveaux de pression acoustique d'émission au poste de travail et en d'autres positions spécifiées (ISO 11200:1995)
Akustika - Emisija hrupa naprav in opreme - Smernice za uporabo temeljnih standardov za ugotovljanje emisijske ravni zvočnega tlaka na mestu delovanja in na drugih opredeljenih mestih (ISO 11200:1995)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11200:1997
01-april-1997
$NXVWLND(PLVLMDKUXSDQDSUDYLQRSUHPH6PHUQLFH]DXSRUDERWHPHOMQLK
VWDQGDUGRY]DXJRWRYOMDQMHHPLVLMVNHUDYQL]YRþQHJDWODNDQDPHVWXGHORYDQMDLQ
QDGUXJLKRSUHGHOMHQLKPHVWLK ,62
Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic
standards for the determination of emission sound pressure levels at a work station and
other specified positions (ISO 11200:1995)
Akustik - Geräuschabstrahlung von Maschinen und Geräten - Leitlinien zur Anwendung
der Grundnormen zur Bestimmung von Emissions-Schalldruckpegeln am Arbeitsplatz
und an anderen festgelegten Orten (ISO 11200:1995)
Acoustique - Bruit émis par les machines et équipements - Guide d'utilisation des
normes de base pour la détermination des niveaux de pression acoustique d'émission au
poste de travail et en d'autres positions spécifiées (ISO 11200:1995)
Ta slovenski standard je istoveten z: EN ISO 11200:1995
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
SIST EN ISO 11200:1997 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 2 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 3 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 4 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 5 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 6 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 7 ----------------------
SIST EN ISO 11200:1997
---------------------- Page: 8 ----------------------
SIST EN ISO 11200:1997
INTERNATIONAL IS0
STANDARD 11200
First edition
1995-l 2-15
Acoustics - Noise emitted by machinery
and equipment
- Guidelines for the use
of basic standards for the determination of
emission sound pressure levels at a work
station and at other specified positions
Acoustique - Bruit 6mis par /es machines et Quipements - Guide
d’utilisation des normes de base pour la determination des niveaux de
pression acoustique d’6mission au poste de travail et en d’autres positions
sp&if@es
Reference number
IS0 11 ZOO:1 995(E)
---------------------- Page: 9 ----------------------
SIST EN ISO 11200:1997
IS0 11200:1995(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 11200 was prepared by Technical Committee
ISO/TC 43, Acoustics, Subcommittee SC 1, Noise.
Annex A forms an integral part of this Inter national Standard. Annex B is
for information only.
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 10 ----------------------
SIST EN ISO 11200:1997
0 IS0 IS0 11200:1995(E)
Introduction
0.1 Control of noise from machinery or equipment requires effective
exchange of acoustical information among the several parties concerned.
These include the manufacturer, installer and user of the machinery or
equipment. This acoustical information is obtained from measurements.
These measurements are useful only if the conditions under which they
are carried out are specified, if they yield defined acoustical quantities, and
if they are made using standardized instruments.
Two quantities which complement one another can be used to describe
the sound emission of machinery or equipment. One of them is the sound
power level and the other is the emission sound pressure level at a
specified position. The International Standards which describe the basic
methods of determining the sound power level are IS0 3740 to IS0 3747
and IS0 9614-I and IS0 9614-2. This International Standard introduces a
series of four International Standards describing various methods for de-
termining emission sound pressure levels of machinery and equipment.
Emission sound pressure levels are sound pressure levels at one or more
positions located in the vicinity of an item of machinery or equipment,
which arise solely from the noise emitted by that machinery or equipment
when it performs a specified function under given operating conditions,
on a particular mounting in a defined acoustic environment. The operating
and mounting conditions are the same as those used in the determination
of sound power levels. The positions with which this series of International
Standards is concerned include work stations, normally specified in a noise
test code (if one exists), occupied by one or more operators of the ma-
chinery, and other positions which may be occupied from time to time by
other persons. The positions may be located in the vicinity of the ma-
chinery, or in a cab, or in some other enclosure more or less remote from
the machinery. Emission sound pressure levels may arise from contin-
uous, steady operational machinery or they may be averages for a defined
work cycle; they are not averages over a total working day during which
the machinery might perform different functions, operate at different
control settings, or undergo changes of work load.
Emission sound pressure levels in conjunction with sound power levels
are used for declaration of the noise emitted under the defined conditions,
verification of declared values, comparison of the noise emitted by ma-
chinery of various types and sizes, comparison with limits specified in a
purchasing contract or a regulation, engineering work to reduce the noise
emission of machinery, and prediction of noise exposure at the specified
positions.
For many products, the sound power level is the primary metric for com-
parison of noise emissions. Noise test codes and specific declaration
codes should state the primary metric for comparison.
. . .
Ill
---------------------- Page: 11 ----------------------
SIST EN ISO 11200:1997
0 IS0
IS0 11200:1995(E)
It is not the intent of this series of International Standards to describe
procedures for measuring the occupational noise exposure of workers.
Included in this series of International Standards are three which describe
procedures for measuring emission sound pressure levels directly, in dif-
ferent test environments (IS0 11201, IS0 11202 and IS0 11204), and a
fourth (IS0 11203) which gives procedures for determining emission
sound pressure levels from the sound power level. When applying these
standards to sound measurements on specific machinery, it is necessary
to decide which is the most appropriate for the particular type of machin-
ery or equipment and for the purpose of the test. Guidelines for making
this decision are provided in this International Standard.
0.2 The series of International Standards for which this International
Standard serves as the introduction comprises IS0 11201, IS0 11202,
IS0 11203 and IS0 11204. In principle, the methods of determining
emission sound pressure levels described in IS0 11201 to IS0 11204
cover all types of machinery and equipment. For noise measurements on
a particular kind and size of machinery or equipment, or when there are
certain practical limitations, only one of these International Standards may
be applicable.
IS0 11201 to IS0 II 204 make up a set of basic International Standards
which specify the acoustical conditions and instrumentation to be used,
describe the procedures to be followed, and give general information on
the installation and operation of the machine under test, when determining
emission sound pressure levels. In general, these sound pressure levels
are different from those that would occur if the machinery or equipment
were operating in its normal surroundings, where the environment may
influence the emission sound pressure level. The selection of standards
for the determination of the sound power level can, for practical reasons,
have consequences on the selection of standards for the determination
of the emission sound pressure level. It is preferable to make the choice
of standards concurrently with respect to the two noise emission quan-
tities.
0.3 This International Standard is one of a series which specifies various
methods for determining the noise emissions of a piece of machinery or
equipment, or a sub-assembly of such equipment (machine under test).
Standards in this series are grouped in three categories, as follows.
a) Methods for the determination of emission sound pressure levels
at work stations and at other specified positions
In addition to this International Standard, this category includes the
following standards (see table 1):
- IS0 11201 gives an engineering method for measuring emission
sound pressure levels of machinery and equipment, in an essen-
tially free field over a reflecting plane, with no environmental cor-
rection;
- IS0 11202 gives a survey method for measuring emission sound
pressure levels of machinery and equipment in situ with an en-
vironmental correction using a simplified method;
---------------------- Page: 12 ----------------------
SIST EN ISO 11200:1997
0 IS0 IS0 11200:1995(E)
- IS0 11203 gives two alternative methods for determining the
emission sound pressure levels of machinery and equipment from
the sound power levels;
- IS0 11204 gives a method for measuring the emission sound
pressure levels of machinery and equipment yielding engineering
grade or survey grade results.
Methods for the determination of sound power levels
b)
- IS0 3740 gives guidelines for the choice of the method to be used
for determining the sound power emitted by machinery and
equipment;
- IS0 3741 to IS0 3747 give methods for determining the sound
power levels of machinery and equipment via sound pressure
measurements;
- parts 1 and 2 of IS0 9614 describe methods for determining the
sound power levels of machinery and equipment via sound inten-
sity measurements.
c) Noise tests codes
For a particular family of machinery or equipment, noise test codes
specify:
- the meth od to be used for the determination of the sound p ower
- the method to be used for the determination of emission sound
pressure levels at work stations, and at other specified positions;
- the positions of the work stations;
- the mounting and operating conditions of the machine under test
for the purpose of determining the noise emission quantities;
- the method to be used for verifying declared noise emission
quantities.
V
---------------------- Page: 13 ----------------------
SIST EN ISO 11200:1997
This page intentionally left blank
---------------------- Page: 14 ----------------------
SIST EN ISO 11200:1997
IS0 11200:1995(E)
INTERNATIONAL STANDARD 0 IS0
Acoustics - Noise emitted by machinery and
- Guidelines for the use of basic standards
equipment
for the determination of emission sound pressure
levels at a work station and at other specified positions
2 Normative references
1 Scope
This International Standard provides brief summaries
of the basic International Standards for determining
The following standards contain provisions which,
emission sound pressure levels from all types of ma-
through reference in this text, constitute provisions
chinery and equipment, at work stations and at other
of this International Standard. At the time of publi-
specified positions, and gives guidance on the pro-
cation, the editions indicated were valid. All standards
cess of selection of which is appropriate to any par-
are subject to revision, and parties to agreements
ticular type. The guidance given applies only to
based on this International Standard are encouraged
airborne sound, and is for use in the preparation of
to investigate the possibility of applying the most re-
noise test codes, and also for use in noise testing
cent editions of the standards indicated below.
where no noise test code exists.
Members of IEC and IS0 maintain registers of cur-
rently valid International Standards.
It is important that specific noise test codes for vari-
ous types of machinery and equipment be established
IS0 2204:1979, Acoustics - Guide to International
and used in accordance with the requirements of
Standards on the measurement of airborne acoustical
these basic International Standards. Such standard- noise and evaluation of its effects on human beings.
ized noise test codes will give detailed requirements
on mounting and operating conditions for the particu- IS0 3740: 1980, Acoustics - Determination of sound
lar family to which the machine under test belongs, power levels of noise sources - Guidelines for the
as well as the location of the work station(s) and other use of basic standards and for the preparation of noise
specified positions as prescribed in these International test codes.
Standards. The data so obtained may also be used for
IS0 3741 :I 988, Acoustics - Determination of sound
the declaration and verification of emission sound
power levels of noise sources - Precision methods
pressure levels as specified in IS0 4871.
for broad-band sources in reverberation rooms.
NOTE 1 At any given position in relation to a particular
machine, and for given mounting and operating conditions, IS0 3742:1988, Acoustics
- Determination of sound
the emission sound pressure levels determined by any of
power levels of noise sources - Precision methods
the methods given in IS0 11201 to IS0 11204 will in gen-
for discrete-frequency and narrow-band sources in
eral be lower than the directly measured sound pressure
reverberation rooms.
levels for the same machine in the typical workroom where
it is used. This is due to reverberation and the contributions
IS0 3743-l :I 994, Acoustics - Determination of
of other machines. A method of calculating the sound
sound power levels of noise sources - Engineering
pressure levels in the vicinity of a machine operating alone
methods for small, movable sources in reverberant
in a workroom is given in IS0 11690-3. Commonly observed
fields - Part I: Comparison method for hard-walled
differences are 1 dB to 5 dB, but in extreme cases the dif-
test rooms.
ference may be even greater.
---------------------- Page: 15 ----------------------
SIST EN ISO 11200:1997
0 IS0
IS0 11200:1995(E)
IS0 3743-2:1994, Acoustics - Determination of IS0 12001 :I 995, Acoustics - Noise emitted by ma-
chinery and equipment - Rules for the drafting and
sound power levels of noise sources using sound
presentation of a noise test code.
pressure - Engineering methods for small, movable
sources in reverberant fields - Part 2: Methods for
IEC 651: 1979, Sound level meters.
special reverberation test rooms.
I EC 804: 1985, Integrating-averaging sound level
IS0 3744: 1994, Acoustics - Determination of sound
meters.
power levels of noise sources using sound pressure
- Engineering method in an essentially free field over
I EC 942: 1988, Sound calibrators.
a reflecting plane.
IEC 1260: -*), Electroacoustics - Octave-band and
IS0 3745: 1977, Acoustics - Determination of sound
fractional-octave-band filters.
power levels of noise sources - Precision methods
for anechoic and semi-anechoic rooms.
of sound
IS0 3746:1995, Acoustics - Determination
3 Definitions
pressure
power levels of noise sources using sound
- Survey method using an enveloping measurement
For the purposes of this International Standard, the
surface over a reflecting plane.
following definitions apply. More detailed definitions
- Determination of sound may be found in noise test codes for specific types
IS0 3747: 1987, Acoustics
of machinery and equipment.
power levels of noise sources - Survey method us-
ing a reference sound source.
3.1 emission: Airborne sound radiated by a well-
IS0 9614-I :I 993, Acoustics - Determination of
defined noise source (e.g. the machine under test).
sound power levels of noise sources using sound in-
tensity - Part I: Measurement at discrete points.
NOTE 2 Noise emission descriptors may be incorporated
in a product label and/or product specification. The basic
noise emission descriptors are the sound power level of the
IS0 9614-2: -‘I, Acoustics - Determination of sound
source itself and the emission sound pressure levels at a
power levels of noise sources using sound intensity
work station and/or at other specified positions (if any) in the
- Part 2: Measurement by scanning.
vicinity of the source.
IS0 11201 :I 995, Acoustics - Noise emitted by ma-
3.2 emission sound pressure, p: The sound press-
chinery and equipment - Measurement of emission
ure, at a specified position near a noise source, when
sound pressure levels at a work station and at other
the source is in operation under specified operating
specified positions - Engineering method in an es-
and mounting conditions on a reflecting plane surface,
sentially free field over a reflecting plane.
excluding the effects of background noise as well as
the effects of reflections other than those from the
IS0 11202:1995, Acoustics - Noise emitted by ma-
chinery and equipment - Measurement of emission plane or planes permitted for the purpose of the test.
sound pressure levels at a work station and at other It is expressed in pascals.
specified positions - Survey method in situ.
3.3 emission sound pressure level, Lp: Ten times
IS0 11203:1995, Acoustics - Noise emitted by ma-
the logarithm to the base IO of the ratio of the square
chinery and equipment - Determination of emission
of the emission sound pressure, p* t), to the square
1
sound pressure levels at a work station and at other
of the reference sound pressure, po, measured with
specified positions from the sound power level.
a particular time weighting and a particular frequency
weighting, selected from those defined in IEC 651. It
IS0 11204:1995, Acoustics - Noise emitted by ma-
is expressed in decibels. The reference sound press-
- Measurement of emission
chinery and equipment
ure is 20 PPa.
sound pressure levels at a work station and at other
specified positions - Method requiring environ-
NOTE 3 Examples include:
mental corrections.
- maximum A-weighted emission sound pressure level
with time-weighting F: LPAFmax;
1) To be published. -
2) To be published. (Revision of IEC 225:1966)
2
---------------------- Page: 16 ----------------------
SIST EN ISO 11200:1997
0 IS0 IS0 11200:1995(E)
- C-weighted peak emission sound pressure level: a controlled a co environment are used for the
L measurements.
&peak-
3.7 work station; operator’s position: Position in
The emission sound pressure level shall be deter-
the vicinity of the machine under test which is in-
mined at a specified position in accordance with either
tended for the operator.
a test code for a specific family of machines or, if no
test code exists, a method that complies with the
3.8 operator: Individual whose work station is in the
IS0 11200 series.
vicinity of a machine and who is performing a work
task associated with that machine.
3.4 sound power, ‘ur: The rate per unit time at
which airborne sound energy is radiated by a source.
3.9 specified position: Position defined in relation
It is expressed in watts.
to a machine, including, but not limited to, an oper-
ator’s position. The position can be a single, fixed
point, or a combination of points along a path or on a
3.5 sound power llevel, &,: Ten times the logarithm
surface located at a specified distance from the ma-
to the base IO of the ratio of the sound power radi-
chine, as described in the relevant noise test c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.