SIST EN ISO 2898-1:2000

Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996)

Establishes a system of designation for plasticized poly(vinyl chloride) (PVC-P) which may be used as the basis for specifications. PVC-P plastics are differentiated by a classification system based on appropriate levels of properties such as Shore hardness, density and torsional-stiffness temperature at 300 MPa and on information about physical form, intended application, additives and colorants. Replaces the second edition.

Kunststoffe - Weichmacherhaltige Polyvinylchlorid (PVC-P)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 2898-1:1996)

Plastiques - Matériaux a base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage et extrusion - Partie 1: Systeme de désignation et base de spécification (ISO 2898-1:1996)

La présente partie de l'ISO 2898 est applicable à toutes les compositions plastifiées d'homopolymères et de copolymères qui contiennent au moins 50 % (m/m) de chlorure de vinyle. Elle est également applicable aux compositions plastifiées qui contiennent du poly(chlorure de vinyle) chloré et à celles qui contiennent des mélanges constitués d'un ou plusieurs polymères parmi ceux susmentionnés, sous réserve que la teneur totale en ces polymères soit égale à au moins 50 % (m/m) du mélange de polymères de la composition. La présente partie de l'ISO 2898 s'applique aux matériaux prêts à l'emploi sous forme de poudre (mélange sec), grains ou granulés, non modifiés ou modifiés par des colorants, additifs, charges, etc. La présente partie de l'ISO 2898 ne s'applique ni aux plastiques cellulaires, ni aux compositions en pâte (plastisols). Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. La présente partie de l'ISO 2898 ne comporte pas de données sur la conception, la performance ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en oeuvre. Si de telles propriétés additionnelles sont nécessaires, elles doivent être déterminées conformément aux méthodes d'essai prescrites dans l'ISO 2898-2, le cas échéant. Afin de prescrire un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en oeuvre reproductible, des exigences additionnelles peuvent être indiquées dans le bloc de données 5 (voir article 3, premier alinéa).

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz mehčanega polivinilklorida (PVC-P) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 2898-1:1996)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2000
• Withdrawal Date: 03-Jun-2020
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 04-Jun-2020
• Due Date: 27-Jun-2020
• Completion Date: 04-Jun-2020
• Ref Project: EN ISO 2898-1:1999 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996)

Relations

• Replaced By: SIST EN ISO 24023-1:2020 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24023-1:2020)
• Effective Date: 03-Jun-2020
• Revised: SIST EN ISO 24023-1:2020 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24023-1:2020)
• Effective Date: 16-Jan-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2898-1:2000
01-maj-2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]PHKþDQHJD
SROLYLQLONORULGD39&3GHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH
,62
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part
1: Designation system and basis for specifications (ISO 2898-1:1996)
Kunststoffe - Weichmacherhaltige Polyvinylchlorid (PVC-P)-Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 2898-1:1996)
Plastiques - Matériaux a base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage
et extrusion - Partie 1: Systeme de désignation et base de spécification (ISO 2898-
1:1996)
Ta slovenski standard je istoveten z: EN ISO 2898-1:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 2898-1:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 2898-1:2000
I NTE R NAT1 O NAL
IS0
STANDARD 2898- I
Third edition
1996-08-1 5
Plastics - Plasticized poly(viny1 chloride)
(PVC-P) moulding and extrusion
materials -
Part 1:
Designation system and basis for
specifications
Plastiques - Matériaux à base de poly(ch1orure de vinyle) plastifié (PVC-P)
pour moulage et extrusion -
Partie 1: Système de désignation et base de spécification
Reference number
IS0 2898-1 11 996(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 2898-1:2000
IS0 2898-1 :1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide fed-
eration of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 YO of the member bodies casting
a vote.
International Standard IS0 2898-1 was prepared by Technical Committee
lSO/lC 61, Plastics, Subcommittee SC 9, Thermoplastics.
This third edition cancels and replaces the second edition
(IS0 2898-1 :I 986) and includes the following changes:
the text has been brought into line with latest version of the so-called
"frame text";
"tape manufacture" has been added in data block 2 as a possible
application.
IS0 2898 consists of the following parts, under the general title Plastics -
Plasticized polyfvin y1 chloride) (PVC-P) moulding and extrusion materials.
-
Part I: Designation system and basis for specifications
-
Part 2: Preparation of test specimens and determination of properties
O IS0 1996
All rights reserved Unless otherwise specified, no part of this publication may be
reproduced or utilized in any form or by any means, electronic or mechanical, including
photocopying and microtilm without permission in writing from the publisher
International Organization for Standardization
Case Postale 56 CH-1 21 1 Geneve 20 Switzerland
Printed in Switzerland
II

---------------------- Page: 8 ----------------------

SIST EN ISO 2898-1:2000
INTERNATIONAL STANDARD 0 IS0 IS0 2898-1 : 1996( E)
Plastics - Plasticized poly(viny1 chloride) (PVC-P) moulding
-
and extrusion materials
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of IS0 2898 establishes a system of designation for plasticized thermoplastic material which may be
used as the basis for specifications.
1.2 The types of PVC-P plastics are differentiated from each other by a classification system based on appropriate
levels of the designatory properties
a) Shore hardness
b) density
torsional-stiffness temperature at 300 MPa
c)
and on information about physical form, intended application and/or method of processing, important properties,
additives and colorants.
1.3 This part of IS0 2898 is applicable to all plasticized compositions of homopolymers and copolymers that con-
tain at least 50 Yo (m/m) of vinyl chloride. It is also applicable to plasticized compositions containing chlorinated
poly(viny1 chloride) and to plasticized compositions containing blends of one or more of the above-mentioned poly-
mers, provided that the total amount of these polymers represents at least 50 % (m/m) of the polymer content of
the composition.
This part of IS0 2898 applies to materials ready for normal use in the form of powder (dry blends), granules or pel-
lets, unmodified or modified by colorants, additives, fillers, etc.
This part of IS0 2898 does not apply IO cellular plastics or to paste compositions (plastisols).
1.4 It is not intended to imply that materials having the same designation give necessarily the same performance.
This part of IS0 2898 does not provide engineering data, performance data or data on processing conditions which
may be required to specify a material for a particular application and/or method of processing.
If such additional properties are required, they shall be determined in accordance with the test methods specified in
part 2 of this International Standard, if suitable.
1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible processing,
additional requirements may be given in data block 5 (see clause 3, first paragraph).
1

---------------------- Page: 9 ----------------------

SIST EN ISO 2898-1:2000
IS0 2898-1 : 1996( E) 0 IS0
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part
of IS0 2898. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of IS0 2898 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently
valid International Standards.
IS0 1043-1 :- 11, Plastics - Symbols and abbreviated terms - Part I: Basic polymers and their special character-
istics.
I SO 2898-2:- z), Plastics - Plasticized polylvinyl chloride) (PVC-P) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties.
3 Designation and specification system
The designation and specification system for thermoplastics is based on the following standardized pattern:
I Designation 1
Description Identity block
block International Individual-item block
(optional) Standard Data Data Data Data Data
Number block block block block block block
1 2 3 4 5
The designation consists of an optional description block, reading "Thermoplastics", and an
...