SIST EN 10248-2:1998
(Main)Hot rolled sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions
Hot rolled sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions
This part of this European standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled non alloy steel sheet piles which are defined in EN 10248-1.
Warmgewalzte Spundbohlen aus unlegierten Stählen - Teil 2: Grenzabmaße und Formtoleranzen
In diesem Teil der Europäischen Norm sind die Grenzabmaße, der Höhe, Breite, Wanddicke und Länge sowie die Grenzabweichungen des Schnitts rechtwinklig zur Längsachse, der Geradheit und der Masse von warmgewalzten unlegierten Spundbohlen nach EN 10248-1 festgelegt.
Palplanches laminées a chaud en aciers non alliés - Partie 2: Tolérances sur forme et dimensions
La présente partie de la présente norme européenne spécifie les tolérances relatives aux dimensions, a l'équerrage des extrémités, a la rectitude et a la masse des palplanches laminées a chaud en aciers non alliés dans l'EN 10248-1.
Vroče valjana obešala iz nelegiranih jekel - 2. del: Mejni odstopki mer in tolerance oblik
General Information
RELATIONS
Standards Content (sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.REOLNWarmgewalzte Spundbohlen aus unlegierten Stählen - Teil 2: Grenzabmaße und FormtoleranzenPalplanches laminées a chaud en aciers non alliés - Partie 2: Tolérances sur forme et dimensionsHot rolled sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions77.140.70Jekleni profiliSteel profiles77.140.45Nelegirana jeklaNon-a
...This May Also Interest You
This part of this standard specifies the technical delivery conditions for electric welded and submerged arc welded cold formed structural steel hollow sections for mechanical engineering purposes of circular, square, rectangular or elliptical forms and applies to structural hollow sections formed cold without subsequent heat treatment other than the heat treatment of the weld line.
NOTE 1 The requirements for tolerances, dimensions and sectional properties can be found in EN 10219-2.
NOTE 2 T...view more
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10210 specifies tolerances for hot finished circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 800 mm x 800 mm
Rectangular: Outside dimensions up to 750 mm x 500 mm
Elliptical: Outside dimensions up to 500 mm x 250 mm
The formulae for calculating sectional properties of sections manufactured to the d...view more
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10219 specifies tolerances for cold formed welded circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 500 mm x 500 mm
Rectangular: Outside dimensions up to 500 mm x 300 mm
Elliptical: Outside dimensions up to 480 mm x 240 mm
The formulae for calculating sectional properties of sections manufactured to ...view more
- Standard44 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2.
NOTE A range of ma...view more
- Standard38 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the technical delivery conditions for cold formed welded structural hollow sections of circular, square or rectangular forms and applies to structural hollow sections formed cold without subsequent heat treatment.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10219-2.
NOTE A range of steel grades is specified in this European Standard and the user should select the grade appropriate to the intended use and ser...view more
- Standard35 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the requirements for cold formed non alloy steel sheet piling produced from hot rolled strip or sheet with a thickness equal to or greater than 2mm in respect of its chemical composition, mechanical and technological properties and delivery conditions. The products specified are for general, structural and civil engineering works. Requirements concerning the tolerances on shape and dimensions are specified in Part 2 of this European Standard.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European standard specifies the requirements for hot rolled non alloy steel sheet piling in respect of its chemical composition, mechanical properties and conditions of delivery. The products specified are for general, structural and civil engineering works. Requirements in respect of tolerances onshape and dimensions are specified in Part 2 of this European Standard.
- Standard15 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed non alloy steel sheet piles which are defined in EN 10249-1.
- Standard8 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10219 specifies the product characteristics, test methods and performance criteria for electric welded and submerged arc welded cold formed structural steel hollow sections of circular, square, rectangular or elliptical forms, produced without any subsequent heat treatment other than the heat treatment of the weld line.
Requirements for the technical delivery conditions are specified in prEN 10219-2 and for tolerances, dimensions and sectional properties in prEN 10219-3.
NOTE...view more
- Draft20 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the requirements for hot rolled non alloy steel sheet piling in respect of its chemical composition, mechanical properties and conditions of delivery.The products specified are for general, structural and civil engineering works.Requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this European Standard.
- Draft38 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold-formed non alloy steel sheet piling which are defined in EN 10249-1.
- Draft10 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the requirements for cold formed non alloy steel sheet piling produced from hot rolled strip or sheet with a thickness equal to oe greater than 2 mm in respect of its chemical composition, mechanical and technological properties and delivery conditions.The products specified are for general, structural and civil engineering works.Requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this European Standard.
- Draft26 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10210 specifies the product characteristics, test methods and performance criteria for hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical conditions to those obtained in the hot formed product.
Requirem...view more
- Draft20 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies technical delivery conditions for hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical conditions to those obtained in the hot formed product.
The general conditions (product c...view more
- Draft42 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled non alloy steel sheet piling which are defined in EN 10248-1.
- Draft22 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10219 specifies the technical delivery conditions for electric welded and submerged arc welded cold formed structural steel hollow sections of circular, square, rectangular or elliptical forms and applies to structural hollow sections formed cold without subsequent heat treatment.
The general conditions (product characteristics, test methods and performance criteria that apply under the Construction Products Regulations) are specified in prEN 10219-1 and the requirements for t...view more
- Draft39 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this standard specifies the technical delivery conditions for electric welded and submerged arc welded cold formed structural steel hollow sections for mechanical engineering purposes of circular, square, rectangular or elliptical forms and applies to structural hollow sections formed cold without subsequent heat treatment other than the heat treatment of the weld line.
NOTE 1 The requirements for tolerances, dimensions and sectional properties can be found in EN 10219-2.
NOTE 2 T...view more
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10210 specifies tolerances for hot finished circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 800 mm x 800 mm
Rectangular: Outside dimensions up to 750 mm x 500 mm
Elliptical: Outside dimensions up to 500 mm x 250 mm
The formulae for calculating sectional properties of sections manufactured to the d...view more
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of prEN 10219 specifies tolerances for cold formed welded circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 500 mm x 500 mm
Rectangular: Outside dimensions up to 500 mm x 300 mm
Elliptical: Outside dimensions up to 480 mm x 240 mm
The formulae for calculating sectional properties of sections manufactured to ...view more
- Standard44 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2.
NOTE A range of ma...view more
- Standard38 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.