SIST EN 10248-2:2024
(Main)Hot rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
Hot rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled steel sheet piles and is designed to be read in conjunction with EN 10248-1.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars.
This document also specifies options that can be agreed between the purchaser and the manufacturer at the time of the order and enquiry.
Warmgewalzte Spundbohlen aus Stahl - Teil 2: Grenzabmaße und Formtoleranzen
Dieses Dokument legt die Grenzabmaße sowie die Rechtwinkligkeit der Enden, die Geradheit und die Masse von warmgewalzten Spundbohlen fest und ist zusammen mit der EN 10248-1 zu verwenden.
Die Erzeugnisse sind für allgemeine, strukturelle Anwendungen und für das Bauwesen verwendbar. Die Arten von Spundbohlen in diesem Dokument sind: Z-Profil, U-Profil, Flachprofil, H-Profil mit ihren Verbindungsschlössern.
Dieses Dokument legt auch Optionen fest, die zwischen dem Hersteller und dem Besteller bei der Anfrage und Bestellung vereinbart werden können.
Palplanches en acier laminées à chaud - Partie 2 : Tolérances sur dimensions et forme
Le présent document spécifie les tolérances relatives aux dimensions, à l'équerrage des extrémités, à la rectitude et à la masse des palplanches en acier laminées à chaud et est conçu pour être lu conjointement avec l’EN 10248-1.
Les produits désignés sont destinés à être utilisés dans la réalisation d'ouvrages divers, d'ouvrages de génie civil et d'éléments de construction. Les types de palplanches en acier couverts dans le présent document sont : les palplanches en Z, en U, plates, en H avec leurs serrures.
Le présent document spécifie également les options qui peuvent être convenues entre l'acheteur et le fabricant au moment de la commande et de l’appel d’offres.
Vroče valjane jeklene zagatnice - 2. del: Mejni odstopki mer in tolerance oblik
Ta dokument določa mejne odstopke mer in tolerance pravokotnosti na koncih, ravnosti in mase vroče valjanih jeklenih zagatnic ter je zasnovan tako, da se uporablja skupaj s standardom EN 10248-1.
Navedeni izdelki so namenjeni za splošna, konstrukcijska in gradbena dela. Ta dokument zajema naslednje vrste jeklenih zagatnic: v obliki črke Z, črke U, ravne mreže in obliki črke H s prepletenimi palicami.
Ta dokument prav tako določa možnosti, o katerih se lahko dogovorita kupec in proizvajalec v času naročila in povpraševanja.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Vroče valjane jeklene zagatnice - 2. del: Mejni odstopki mer in tolerance oblik
Hot rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
Warmgewalzte Spundbohlen aus Stahl - Teil 2: Grenzabmaße und Formtoleranzen
Palplanches en acier laminées à chaud - Partie 2 : Tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: EN 10248-2:2024
ICS:
77.140.70 Jekleni profili Steel profiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 10248-2
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2024
EUROPÄISCHE NORM
ICS 77.140.70 Supersedes EN 10248-2:1995
English Version
Hot-rolled steel sheet piles - Part 2: Tolerances on
dimensions and shape
Palplanches en acier laminées à chaud - Partie 2 : Warmgewalzte Spundbohlen aus Stahl - Teil 2:
Tolérances sur dimensions et forme Grenzabmaße und Formtoleranzen
This European Standard was approved by CEN on 10 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10248-2:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 General requirements . 4
5 Height of profiles . 5
5.1 U-shaped sheet piles . 5
5.2 Z-shaped sheet piles. 5
5.3 H-shaped sheet piles . 6
6 Width of profiles . 7
6.1 U-shaped sheet piles . 7
6.2 Z-shaped sheet piles. 8
6.3 Straight web sheet piles . 9
6.4 H-shaped sheet piles . 9
7 Wall thicknesses of profiles . 10
7.1 U-shaped sheet piles . 10
7.2 Z-shaped sheet piles. 10
7.3 Straight web sheet piles . 11
7.4 H-shaped sheet piles . 12
8 Straightness of profiles (deviation from straight line) . 13
9 Length of profiles . 14
10 Squareness of ends of profiles . 14
11 Mass of profiles . 16
12 Interlocks of profiles . 16
13 Options . 17
European foreword
This document (EN 10248-2:2024) has been prepared by Technical Committee CEN/TC 459/SC 3
“Structural steels other than reinforcements”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2025, and conflicting national standards shall
be withdrawn at the latest by January 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10248-2:1995.
a) restructure of the standard;
b) update of the normative references and general requirements;
c) review of the sketches;
d) new wording for Clause 10;
e) new wording for Clause 11 about the mass tolerance;
f) insertion of a new Table 15 about the misalignment of the head of sheet piles.
EN 10248 consists of the following parts under the general title Hot rolled steel sheet piles:
— Part 1: Technical delivery conditions
— Part 2: Tolerances on dimensions and shape
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot
rolled steel sheet piles and is designed to be read in conjunction with EN 10248-1.
The products specified are for general, structural and civil engineering works. The types of steel sheet
piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking
bars.
This document also specifies options that can be agreed between the purchaser and the manufacturer at
the time of the order and enquiry.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10021:2006, General technical delivery conditions for steel products
EN 10079:2007, Definition of steel products
EN 10248-1, Hot-rolled steel sheet piles - Part 1: Technical delivery conditions
EN 12063, Execution of special geotechnical work - Sheet pile walls, combined pile walls, high modulus walls
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10021:2006, EN 10079:2007
apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/ui
— IEC Electropedia: available at https://www.electropedia.org/
4 General requirements
The tolerances on dimensions and shape of this document shall apply, as far as possible, in addition to
the technical delivery conditions of EN 10248-1.
The determination of sheet pile dimensions and tolerances shall comply with the following preparation
before any measurement is carried out. This requirement sh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.