SIST EN ISO 10893-4:2011
(Main)Non-destructive testing of steel tubes - Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections (ISO 10893-4:2011)
Non-destructive testing of steel tubes - Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections (ISO 10893-4:2011)
This part of ISO 10893 specifies requirements applicable to liquid penetrant testing of seamless and welded tubes for the detection of surface imperfections. It is applicable to all or any part of the tube surface as required by the relevant product standards. It can also be applicable to the testing of hollow sections.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 4: Eindringprüfung nahtloser und geschweißter Stahlrohre zum Nachweis von Oberflächenunregelmäßigkeiten (ISO 10893-4:2011)
Dieser Teil der ISO 10893 legt die Anforderungen an die Eindringprüfung nahtloser und geschweißter Rohre zum Nachweis von Oberflächenunvollkommenheiten fest.
Dieses Dokument ist für die Prüfung aller Teile der Rohroberfläche nach den Anforderungen der entsprechenden Produktnorm anwendbar.
Dieses Dokument kann auch für die Prüfung von Hohlprofilen angewendet werden.
Essais non destructifs des tubes en acier - Partie 4: Contrôle par ressuage des tubes en acier sans soudure ou soudés pour la détection des imperfections de surface (ISO 10893-4:2011)
L'ISO 10893-4:2011 spécifie les exigences applicables au contrôle par ressuage des tubes sans soudure et soudés pour la détection d'imperfections de surface.
Elle est applicable à toute la surface du tube ou à une partie de celle-ci, comme requis par les normes de produits pertinentes.
Elle est également applicable au contrôle des profils creux.
Neporušitveno preskušanje jeklenih cevi - 4. del: Ugotavljanje površinskih nepravilnosti nevarjenih in varjenih jeklenih cevi s tekočimi penetranti (ISO 10893-4:2011)
Ta del ISO 10893 določa zahteve, ki veljajo za ugotavljanje površinskih nepravilnosti nevarjenih in varjenih cevi s tekočimi penetranti. Velja za celotno površino cevi ali njen kateri koli del, kot zahtevajo ustrezni standardi za proizvode. Lahko velja tudi za preskušanje votlih delov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10893-4:2011
01-november-2011
1DGRPHãþD
SIST EN 10246-11:2000
1HSRUXãLWYHQRSUHVNXãDQMHMHNOHQLKFHYLGHO 8JRWDYOMDQMHSRYUãLQVNLK
QHSUDYLOQRVWLQHYDUMHQLKLQYDUMHQLKMHNOHQLKFHYLVWHNRþLPLSHQHWUDQWL ,62
Non-destructive testing of steel tubes - Part 4: Liquid penetrant inspection of seamless
and welded steel tubes for the detection of surface imperfections (ISO 10893-4:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 4: Eindringprüfung nahtloser und
geschweißter Stahlrohre zum Nachweis von Oberflächenunregelmäßigkeiten (ISO 10893
-4:2011)
Essais non destructifs des tubes en acier - Partie 4: Contrôle par ressuage des tubes en
acier sans soudure ou soudés pour la détection des imperfections de surface (ISO
10893-4:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-4:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-4:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-4:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-4:2011
EUROPEAN STANDARD
EN ISO 10893-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-11:2000
English Version
Non-destructive testing of steel tubes - Part 4: Liquid penetrant
inspection of seamless and welded steel tubes for the detection
of surface imperfections (ISO 10893-4:2011)
Essais non destructifs des tubes en acier - Partie 4: Zerstörungsfreie Prüfung von Stahlrohren - Teil 4:
Contrôle par ressuage des tubes en acier sans soudure ou Eindringprüfung nahtloser und geschweißter Stahlrohre
soudés pour la détection des imperfections de surface (ISO zum Nachweis von Oberflächenunvollkommenheiten (ISO
10893-4:2011) 10893-4:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-4:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-4:2011
EN ISO 10893-4:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-4:2011
EN ISO 10893-4:2011 (E)
Foreword
This document (EN ISO 10893-4:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-11:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10893-4:2011 has been approved by CEN as a EN ISO 10893-4:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10893-4:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10893-4:2011
INTERNATIONAL ISO
STANDARD 10893-4
First edition
2011-04-01
Non-destructive testing of steel tubes —
Part 4:
Liquid penetrant inspection of seamless
and welded steel tubes for the detection
of surface imperfections
Essais non destructifs des tubes en acier —
Partie 4: Contrôle par ressuage des tubes en acier sans soudure et
soudés pour la détection des imperfections de surface
Reference number
ISO 10893-4:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 10893-4:2011
ISO 10893-4:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10893-4:2011
ISO 10893-4:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General requirements .2
5 Test method .2
5.1 General .2
5.2 Detection of imperfections and their classification.3
5.3 Procedure.3
6 Evaluation of indications.4
7 Acceptance .6
8 Test report.7
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10893-4:2011
ISO 10893-4:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10893-4 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 19, Technical
delivery conditions for steel tubes for pressure purposes.
This first edition cancels and replaces ISO 12095:1994, which has been technically revised.
ISO 10893 consists of the following parts, under the general title Non-destructive testing of steel tubes:
⎯ Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel
tubes for the verification of hydraulic leaktightness
⎯ Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel
tubes for the detection of imperfections
⎯ Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-
welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections
⎯ Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface
imperfections
⎯ Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of
surface imperfections
⎯ Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections
⎯ Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of
imperfections
⎯ Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar
imperfections
⎯ Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the
manufacture of welded steel tubes
⎯ Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged
arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10893-4:2011
ISO 10893-4:2011(E)
⎯ Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of
longitudinal and/or transverse imperfections
⎯ Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except
submerged arc-welded) steel tubes
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 10893-4:2011
---------------------- Page: 12 ----------------------
SIST EN ISO 10893-4:2011
INTERNATIONAL STANDARD ISO 10893-4:2011(E)
Non-destructive testing of steel tubes —
Part 4:
Liquid penetrant inspection of seamless and welded steel tubes
for the detection of surface imperfections
1 Scope
This part of ISO 10893 specifies requirements applicable to liquid penetrant testing of seamless and welded
tubes for the detection of surface imperfections.
It is applicable to all or any part of the tube surface as required by the relevant product standards.
It can also be applicable to the testing of hollow sections.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3059, Non-destructive testing — Penetrant testing and magnetic particle testing — Viewing conditions
ISO 3452-1, Non-destructive testing — Penetrant testing — Part 1: General principles
ISO 3452-2, Non-destructive testing — Penetrant testing — Part 2: Testing of penetrant materials
ISO 9712, Non destructive testing — Qualification and certification of personnel
ISO 11484, Steel products — Employer’s qualification system for non-destructive testing (NDT) personnel
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3452-1 and ISO 11484 and the
following apply.
3.1
tube
hollow long product open at both ends, of any cross-sectional shape
3.2
seamless tube
tube made by piercing a solid product to obtain a tube hollow, which is further processed, either hot or cold,
into its final dimensions
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 10893-4:2011
ISO 10893-4:2011(E)
3.3
welded tub
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.