SIST-TS CEN ISO/TS 15877-7:2009
(Main)Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009)
This Technical Specification gives guidance for the assessment of conformity included in the manufacturer's quality plan as part of his/her quality system. This Technical Specification includes: a) provisions for materials, components, joints and assemblies given in the applicable part(s) of ISO 15877; b) provisions for the manufacturer's quality system, which can conform to ISO 9001[2]; c) definitions and procedures applied if certification is involved; in which case, the certification body can be accredited to ISO/IEC Guide 65[5] or ISO/IEC 17021[3], as applicable. In conjunction with the other parts of ISO 15877, this Technical Specification is applicable to chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 15877-1:2009).
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der Konformität (ISO/TS 15877-7:2009)
Diese Technische Spezifikation gibt Empfehlungen für die Beurteilung der Konformität im Rahmen des Qualitätssicherungsplans
des Herstellers als Teil von dessen Qualitätssicherungssystem.
Diese Technische Spezifikation enthält:
a) Festlegungen für Werkstoffe, Rohrleitungsteile sowie Verbindungen und Bauteilkombinationen, die im
betreffenden Teil der ISO 15877 festgelegt sind;
b) Festlegungen für das Qualitätssicherungssystem des Herstellers, das ISO 9001 [2] entsprechen kann;
c) Definitionen und Verfahren bei einer Zertifizierung; in diesem Fall kann die Zertifizierungsstelle in
Abhängigkeit der Anwendung nach ISO/IEC Guide 65 [5] oder ISO/IEC Guide 62 [4] akkreditiert sein.
Zusammen mit den übrigen Teilen der ISO 15877 gilt diese Technische Spezifikation für Rohrleitungssysteme
aus chloriertem Polyvinylchlorid (PVC-C), die in der Warm- und Kaltwasserinstallation innerhalb von
Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen
unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse
geltenden Temperaturen (siehe ISO 15877-1:2009, Tabelle 1) eingesetzt werden.
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Poly(chlorure de vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS 15877-7:2009)
L'ISO 15877-7:2009 est un guide pour l'évaluation de la conformité, inclus dans le plan qualité du fabricant dans le cadre de son système qualité.
L'ISO 15877-7:2009 comporte ceci:
– les exigences relatives aux matières, aux composants, aux assemblages et aux montages, énoncées dans la ou les parties applicables de l'ISO 15877;
– les exigences relatives au système qualité du fabricant, qui peut être conforme à l'ISO 9001;
– les définitions et procédures appliquées en cas de certification par tierce partie; en ce cas-là, l'organisme de certification peut être accrédité suivant l'ISO/CEI Guide 65 ou l'ISO/CEI Guide 62, selon le guide approprié.
Conjointement avec les autres parties de l'ISO 15877, l'ISO 15877-7:2009 est applicable aux systèmes de canalisations en poly(chlorure de vinyle) chloré (PVC-C) destinés aux installations d'eau chaude et froide pour le transport de l'eau dans les bâtiments, que l'eau soit ou non destinée à la consommation humaine (systèmes domestiques), à des pressions et des températures de calcul correspondant à la classe d'application (voir le Tableau 1 de l'ISO 15877-1:2009).
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Klorirani polivinilklorid (PVC-C) - 7. del: Navodilo za ugotavljanje skladnosti (ISO/TS 15877-7:2009)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 15877-7:2009
01-december-2009
1DGRPHãþD
SIST-TS CEN ISO/TS 15877-7:2004
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
.ORULUDQLSROLYLQLONORULG 39&& GHO 1DYRGLOR]DXJRWDYOMDQMHVNODGQRVWL
,6276
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl
chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-
7:2009)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes
Polyvinylchlorid (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der Konformität
(ISO/TS 15877-7:2009)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Poly(chlorure de vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de la
conformité (ISO/TS 15877-7:2009)
Ta slovenski standard je istoveten z: CEN ISO/TS 15877-7:2009
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST-TS CEN ISO/TS 15877-7:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
---------------------- Page: 2 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
TECHNICAL SPECIFICATION
CEN ISO/TS 15877-7
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2009
ICS 23.040.01; 23.040.20; 91.140.60 Supersedes CEN ISO/TS 15877-7:2003
English Version
Plastics piping systems for hot and cold water installations -
Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for
the assessment of conformity (ISO/TS 15877-7:2009)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Poly(chlorure de Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-
vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de C) - Teil 7: Empfehlungen für die Beurteilung der
la conformité (ISO/TS 15877-7:2009) Konformität (ISO/TS 15877-7:2009)
This Technical Specification (CEN/TS) was approved by CEN on 22 August 2009 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 15877-7:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
CEN ISO/TS 15877-7:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
CEN ISO/TS 15877-7:2009 (E)
Foreword
This document (CEN ISO/TS 15877-7:2009) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with
Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 15877-7:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
---------------------- Page: 6 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
TECHNICAL ISO/TS
SPECIFICATION 15877-7
Second edition
2009-09-15
Plastics piping systems for hot and cold
water installations — Chlorinated
poly(vinyl chloride) (PVC-C) —
Part 7:
Guidance for the assessment of
conformity
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Poly(chlorure de vinyle) chloré (PVC-C) —
Partie 7: Guide pour l'évaluation de la conformité
Reference number
ISO/TS 15877-7:2009(E)
©
ISO 2009
---------------------- Page: 7 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
Contents Page
Foreword. iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 2
3.1 Terms and definitions. 2
3.2 Abbreviated terms . 4
4 Requirements . 5
4.1 General. 5
4.2 Testing and inspection. 5
Bibliography . 13
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 15877-7 was prepared by European Committee for Standardization (CEN) Technical Committee
CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes
and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This Technical Specification is part of a System Standard for plastics piping systems of a particular material
for a specified application. There are a number of such System Standards.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
They are supported by separate standards on test methods to which references are made throughout the
System Standard.
This second edition cancels and replaces the first edition (ISO/TS 15877-7:2003), which has been technically
revised.
iv © ISO 2009 – All rights reserved
---------------------- Page: 10 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
1)
ISO 15877 consists of the following parts , under the general title Plastics piping systems for hot and cold
water installations — Chlorinated poly(vinyl chloride) (PVC-C):
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fittings
⎯ Part 5: Fitness for purpose of the system
⎯ Part 7: Guidance for the assessment of conformity [Technical Specification]
This Technical Specification can be used to support elaboration of national certification procedures for
products conforming to the applicable part(s) of ISO 15877.
At the date of publication of this Technical Specification, System Standards for piping systems of other
plastics materials used for hot and cold water installations are the following:
ISO 15874 (all parts), Plastics piping systems for hot and cold water installations — Polypropylene (PP)
ISO 15875 (all parts), Plastics piping systems for hot and cold water installations — Crosslinked polyethylene
(PE-X)
ISO 15876 (all parts), Plastics piping systems for hot and cold water installations — Polybutylene (PB)
2)
ISO 22391:— (all parts), Plastics piping systems for hot and cold water installations — Polyethylene of
raised temperature resistance (PE-RT)
1) This System Standard does not incorporate a part 4: Ancillary equipment or a part 6: Guidance for installation. For
ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made from different
[6]
materials, intended to be used for hot and cold water installations, is covered by ENV 12108 .
2) To be published. (Revisions of ISO 22391-1:2007, ISO 22391-2:2007, ISO 22391-3:2007, ISO 22391-5:2007)
© ISO 2009 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
Introduction
This Technical Specification is a part of the System Standard which specifies the requirements for a piping
system when made from chlorinated poly(vinyl chloride) (PVC-C). The piping system is intended to be used
for hot and cold water installations and heating system installations.
In respect of potential adverse effects on the quality of water intended for human consumption caused by the
product covered by ISO 15877 (all parts).
1) This Technical Specification provides no information as to whether the product may be used without
restriction in any of the Member States of the EU or EFTA.
2) It should be noted that, while awaiting the adoption of verifiable European criteria, existing national
regulations concerning the use and/or the characteristics of this product remain in force.
When using solvent cement, relevant national safety rules or regulations concerning their use (e.g. protection
of workers) are to be observed.
Requirements and test methods for material and components are specified in ISO 15877-1, ISO 15877-2 and
ISO 15877-3. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 15877-5.
This Technical Specification gives guidance for the assessment of conformity of materials, components, joints
and assemblies and it is intended to be used by certification bodies, inspection bodies, testing laboratories
and manufacturers.
vi © ISO 2009 – All rights reserved
---------------------- Page: 12 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
TECHNICAL SPECIFICATION ISO/TS 15877-7:2009(E)
Plastics piping systems for hot and cold water installations —
Chlorinated poly(vinyl chloride) (PVC-C) —
Part 7:
Guidance for the assessment of conformity
1 Scope
This Technical Specification gives guidance for the assessment of conformity included in the manufacturer's
quality plan as part of his/her quality system.
This Technical Specification includes:
a) provisions for materials, components, joints and assemblies given in the applicable part(s) of ISO 15877;
[2]
b) provisions for the manufacturer's quality system, which can conform to ISO 9001 ;
c) definitions and procedures applied if certification is involved; in which case, the certification body can be
[5] [3]
accredited to ISO/IEC Guide 65 or ISO/IEC 17021 , as applicable.
In conjunction with the other parts of ISO 15877, this Technical Specification is applicable to chlorinated
poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within
buildings for the conveyance of water, whether or not intended for human consumption (domestic systems),
under design pressures and temperatures appropriate to the class of application (see Table 1 of
ISO 15877-1:2009).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 15877-1:2009, Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl
chloride) (PVC-C) — Part 1: General
ISO 15877-2:2009, Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl
chloride) (PVC-C) — Part 2: Pipes
ISO 15877-3:2009, Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl
chloride) (PVC-C) — Part 3: Fittings
ISO 15877-5:2009, Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl
chloride) (PVC-C) — Part 5: Fitness for purpose of the system
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptable quality limit (AQL) for lot-by-lot inspection
© ISO 2009 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
ISO 3951-1, Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans
indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a
single AQL
ISO 3951-2, Sampling procedures for inspection by variables — Part 2: General specification for single
sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality
characteristics
3 Terms, definitions and abbreviated terms
For the purposes of this Technical Specification, the definitions, symbols and abbreviations given in
ISO 15877-1, ISO 15877-2 and ISO 15877-3 apply, together with the following.
3.1 Terms and definitions
3.1.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and responsibility
to carry out certification of conformity according to given rules of procedure and management
3.1.2
inspection body
impartial organization or company, approved by a certification body as possessing the necessary competence
to verify and/or to carry out initial type testing, audit testing and inspection of the manufacturer's factory
production control in accordance with the relevant standard
3.1.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of
materials and products
3.1.4
quality system
organizational structure, responsibilities, procedures, processes and resources for implementing quality
management
[1]
See ISO 9000 .
3.1.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.1.6
type testing
TT
testing performed to prove that the material, component, joint or assembly is capable of conforming to the
requirements given in the relevant standard
3.1.7
preliminary type testing
PTT
type testing carried out by or on behalf of the manufacturer
3.1.8
initial type testing
ITT
type testing carried out by or on behalf of a certification body for certification purposes
2 © ISO 2009 – All rights reserved
---------------------- Page: 14 ----------------------
SIST-TS CEN ISO/TS 15877-7:2009
ISO/TS 15877-7:2009(E)
3.1.9
batch release test
BRT
test performed by the manufacturer on a batch of components, which has to be satisfactorily completed before
the batch can be released
3.1.10
process verification test
PVT
test performed by the manufacturer on materials, components, joints or assemblies at specific intervals to
confirm that the process continues to be capable of producing components conforming to the requirements
given in the relevant standard
NOTE Such tests are not required to release batches of components and are carried out as a measure of process
control.
3.1.11
audit test
AT
test performed by or on behalf of a certification body to confirm that the material, component, joint or assembly
continues to conform to the requirements given in the relevant standard and to provide information to assess
the effectiveness of the quality system
3.1.12
indirect test
IT
test performed by the manufacturer, different from that specified for that particular characteristic, having
verified its correlation with the specified test
3.1.13
witness testing
WT
testing accepted by a certification body for initial type testing and/or audit testing, which is carried out by or on
behalf of the manufacturer and supervised by a representative of the certification body, qualified in testing
3.1.14
material or compound batch
clearly identifiable quantity of a particular material or compound
3.1.15
production batch
clearly identifiable collection of units, manufactured consecutively or continuous
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.