SIST EN ISO 24026-2:2020
(Main)Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24026-2:2020)
Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24026-2:2020)
1.1 This document specifies the methods of preparation of test specimens and the test methods to
be used in determining the properties of poly(methyl methacrylate) (PMMA) moulding and extrusion
materials. It gives the requirements for handling test material and for conditioning both the test material
before moulding and the specimens before testing.
1.2 This document specifies procedures and conditions for the preparation of test specimens and
procedures for measuring properties of the materials from which these specimens are made. It lists
properties and test methods which are suitable and necessary to characterize poly(methyl methacrylate)
moulding and extrusion materials.
1.3 The properties have been selected from the general test methods in ISO 10350-1. Other test
methods in wide use for, or of particular significance to, these moulding and extrusion materials are also
included in this document, as are the designatory properties specified in ISO 24026-1.
Kunststoffe - Polymethylmethacrylat (PMMA)-Werkstoffe - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 24026-2:2020)
1.1 Dieses Dokument legt die Verfahren zur Herstellung von Probekörpern und die anzuwendenden Prüfverfahren zur Bestimmung der Eigenschaften von Polymethylmethacrylat (PMMA)-Formmassen fest. Es enthält die Anforderungen hinsichtlich der Handhabung des Prüfwerkstoffs und hinsichtlich der Konditionierung des Prüfwerkstoffs vor der Formgebung und der Probekörper vor dem Prüfen.
1.2 Dieses Dokument legt Verfahren und Bedingungen für die Herstellung von Probekörpern und Verfahren zur Messung der Eigenschaften der Materialien, aus denen diese Probekörper bestehen, fest. In ihm werden Eigenschaften und Prüfverfahren, die zur Charakterisierung von Polymethylmethacrylat (PMMA)-Formmassen geeignet und notwendig sind, aufgeführt.
1.3 Die Eigenschaften wurden aus den allgemeinen Prüfverfahren in ISO 10350 1 ausgewählt. Andere Prüfverfahren, die für diese Formmassen breite Anwendung finden oder für diese von besonderer Bedeutung sind, sind ebenfalls in diesem Dokument enthalten, ebenso wie die in ISO 24026 1 festgelegten bezeichnenden Eigenschaften.
Plastiques - Matériaux à base de poly(méthacrylate de méthyle) (PMMA) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 24026-2:2020)
1.1 Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai qui doivent être utilisées pour la détermination des propriétés des matériaux pour moulage et extrusion à base de poly(méthacrylate de méthyle) (PMMA). Il donne les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai.
1.2 Le présent document spécifie les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues sont donnés. Il liste les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base de poly(méthacrylate de méthyle).
1.3 Les propriétés ont été sélectionnées parmi les méthodes d'essai générales de l'ISO 10350-1. D'autres méthodes d'essai largement utilisées ou qui revêtent une importance particulière pour ces matériaux pour moulage et extrusion sont aussi incluses dans le présent document; c'est le cas des propriétés de désignation spécifiées dans l'ISO 24026‑1.
Polimerni materiali - Materiali na osnovi polimetilmetakrilata (PMMA) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 24026-2:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24026-2:2020
01-oktober-2020
Nadomešča:
SIST EN ISO 8257-2:2006
Polimerni materiali - Materiali na osnovi polimetilmetakrilata (PMMA) za
oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje
lastnosti (ISO 24026-2:2020)
Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO 24026-2:2020)
Kunststoffe - Polymethylmethacrylat (PMMA)-Werkstoffe - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO 24026-2:2020)
Plastiques - Matériaux à base de poly(méthacrylate de méthyle) (PMMA) pour moulage
et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO
24026-2:2020)
Ta slovenski standard je istoveten z: EN ISO 24026-2:2020
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 24026-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24026-2:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 24026-2:2020
EN ISO 24026-2
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 8257-2:2006
English Version
Plastics - Poly(methyl methacrylate) (PMMA) moulding
and extrusion materials - Part 2: Preparation of test
specimens and determination of properties (ISO 24026-
2:2020)
Plastiques - Matériaux à base de poly(méthacrylate de Kunststoffe - Polymethylmethacrylat (PMMA)-
méthyle) (PMMA) pour moulage et extrusion - Partie 2: Formmassen - Teil 2: Herstellung von Probekörpern
Préparation des éprouvettes et détermination des und Bestimmung von Eigenschaften (ISO 24026-
propriétés (ISO 24026-2:2020) 2:2020)
This European Standard was approved by CEN on 21 May 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24026-2:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24026-2:2020
EN ISO 24026-2:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24026-2:2020
EN ISO 24026-2:2020 (E)
European foreword
This document (EN ISO 24026-2:2020) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2020, and conflicting national standards
shall be withdrawn at the latest by December 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8257-2:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 24026-2:2020 has been approved by CEN as EN ISO 24026-2:2020 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24026-2:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 24026-2:2020
INTERNATIONAL ISO
STANDARD 24026-2
First edition
2020-05
Plastics — Poly(methyl methacrylate)
(PMMA) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux à base de poly(méthacrylate de méthyle)
(PMMA) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 24026-2:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 24026-2:2020
ISO 24026-2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24026-2:2020
ISO 24026-2:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 2
4.1 General . 2
4.2 Treatment of the material before moulding . 2
4.3 Moulding of specimens . 3
4.3.1 General requirements . 3
4.3.2 Melt temperature . . . 3
4.3.3 Mould temperature . 4
4.3.4 Average melt velocity . 4
4.3.5 Hold pressure . 5
4.3.6 Cooling time . 5
5 Conditioning of test specimens . 5
6 Determination of properties . 5
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24026-2:2020
ISO 24026-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This first edition of ISO 24026-2 cancels and replaces ISO 8257-2:2001, which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the normative references have been updated;
— Clause 3 has been added;
— the contents of Table 3 and Table 4 have been updated.
A list of all parts in the ISO 24026 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 24026-2:2020
INTERNATIONAL STANDARD ISO 24026-2:2020(E)
Plastics — Poly(methyl methacrylate) (PMMA) moulding
and extrusion
...
SLOVENSKI STANDARD
oSIST prEN ISO 24026-2:2019
01-junij-2019
Polimerni materiali - Materiali na osnovi polimetilmetakrilata (PMMA) za
oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje
lastnosti (ISO/DIS 24026-2:2019)
Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO/DIS 24026-2:2019)
Kunststoffe - Polymethylmethacrylat (PMMA)-Werkstoffe - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO/DIS 24026-2:2019)
Plastiques - Matériaux à base de poly(méthacrylate de méthyle) (PMMA) pour moulage
et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés
(ISO/DIS 24026-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 24026-2
ICS:
83.080.20 Plastomeri Thermoplastic materials
oSIST prEN ISO 24026-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 24026-2:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 24026-2:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24026-2
ISO/TC 61/SC 9 Secretariat: KATS
Voting begins on: Voting terminates on:
2019-03-25 2019-06-17
Plastics — Poly(methyl methacrylate) (PMMA) moulding
and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
Plastiques — Poly(méthacrylate de méthyle) (PMMA) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
ICS: 83.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24026-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 24026-2:2019
ISO/DIS 24026-2:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 24026-2:2019
ISO/DIS 24026-2:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 2
4.1 General . 2
4.2 Treatment of the material before moulding . 2
4.3 Moulding of specimens . 3
4.3.1 General requirments . 3
4.3.2 Melt temperature . . . 3
4.3.3 Mould temperature . 4
4.3.4 Average melt velocity . 4
4.3.5 Hold pressure . 4
4.3.6 Cooling time . 4
5 Conditioning of test specimens . 4
6 Determination of properties . 4
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 24026-2:2019
ISO/DIS 24026-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO XXXXX-2 cancels and replaces ISO 24026-2:2001, which has been technically
revised.
ISO XXXXX consists of the following parts, under the general title Plastics — Poly(methyl methacrylate)
(PMMA) moulding and extrusion materials:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test specimens and determination of properties
A list of all parts in the ISO XXXXX series can be found on the ISO website.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 24026-2:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 24026-2:2019(E)
Plastics — Poly(methyl methacrylate) (PMMA) moulding
and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
1.1 This part of ISO XXXXX specifies the methods of preparation of test specimens and the test
methods to be used in determining the properties of Poly(methyl methacrylate)PMMA moulding and
extrusion materials. Requirements for handling test material and for conditioning both the test material
before moulding and the specimens before testing are given here.
1.2 Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test methods
which are suitable and necessary to characterize Poly(methyl methacrylate) moulding and extrusion
materials are listed.
1.3 The properties have been selected from the general test methods in ISO 10350-1. Other test
methods in wide use for, or of particular significance to, these moulding and extrusion materials are also
included in this document, as are the designatory properties specified in ISO XXXXX-1.
1.4 In order to obtain reproducible and comparable test results, it is necessary to use the methods of
specimen preparation and conditioning, the specimen dimensions and the test procedures specified in
this document. Values determined will not necessarily be identical to those obtained using specimens of
different dimensions or prepared using different procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.