oSIST prEN ISO 10749:2008

Footwear - Test method for slide fasteners - Resistance to damage during closure under lateral force (ISO/DIS 10749:2008)

This test method is intended to determine the maximum lateral force applied to a slide fastener for footwear under which it will close without failure.  The method is applicable to all types of slide fastener.

Schuhe - Prüfverfahren für Reißverschlüsse - Beständigkeit gegen Beschädigung während des Schließens unter Einwirkung einer lateralen Kraft (ISO/DIS 10749:2008)

Diese Norm legt ein Prüfverfahren zur Bestimmung der auf einen Reißverschluss für Schuhe aufge¬brachten maximalen lateralen Kraft fest, bei der der Reißverschluss ohne Versagen geschlossen werden kann. Das Verfahren gilt für sämtliche Arten von Reißverschlüssen.

Chaussures - Méthode d'essai pour les fermetures éclair - Résistance à l'endommagement sous contrainte latérale durant la fermeture (ISO/DIS 10749:2008)

Obutev - Preskusna metoda za zadrge - Odpornost proti poškodbam med zapiranjem (delovanje stranske sile) (ISO/DIS 10749:2008)

General Information

• Status: Not Published
• Public Enquiry End Date: 31-Aug-2008
• ICS: 61.040 - Headgear. Clothing accessories. Fastening of clothing
• ICS: 61.060 - Footwear
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 15-Jan-2020
• Due Date: 20-Jan-2020
• Completion Date: 15-Jan-2020
• Ref Project: prEN ISO 10749 - Footwear - Test method for slide fasteners - Resistance to damage during closure under lateral force (ISO/DIS 10749:2008)

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 10749:2008
01-julij-2008
Obutev - Preskusna metoda za zadrge - Odpornost proti poškodbam med
zapiranjem (delovanje stranske sile) (ISO/DIS 10749:2008)
Footwear - Test method for slide fasteners - Resistance to damage during closure under
lateral force (ISO/DIS 10749:2008)
Schuhe - Prüfverfahren für Reißverschlüsse - Beständigkeit gegen Beschädigung
während des Schließens unter Einwirkung einer lateralen Kraft (ISO/DIS 10749:2008)
Chaussures - Méthode d'essai pour les fermetures éclair - Résistance à
l'endommagement sous contrainte latérale durant la fermeture (ISO/DIS 10749:2008)
Ta slovenski standard je istoveten z: prEN ISO 10749
ICS:
61.040 3RNULYDOD'RGDWNLN Headgear. Clothing
REODþLORP6SHQMDQMHREODþLO accessories. Fastening of
clothing
61.060 Obuvala Footwear
oSIST prEN ISO 10749:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 10749
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 61.040

English Version
Footwear - Test method for slide fasteners - Resistance to
damage during closure under lateral force (ISO/DIS
10749:2008)
Chaussures - Méthode d'essai pour les fermetures éclair - Schuhe - Prüfverfahren für Reißverschlüsse - Beständigkeit
Résistance à l'endommagement sous contrainte latérale gegen Beschädigung während des Schließens unter
durant la fermeture (ISO/DIS 10749:2008) Einwirkung einer lateralen Kraft (ISO/DIS 10749:2008)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 309.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 10749:2008: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN ISO 10749:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 3 ----------------------
prEN ISO 10749:2008 (E)
Foreword
This document (prEN ISO 10749:2008) has been prepared by Technical Committee CEN/TC 309 “Footwear”
the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 216 "Footwear".
This document is currently submitted to the parallel Enquiry.

3

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 10749
ISO/TC 216 Secretariat: AENOR
Voting begins on: Voting terminates on:
2008-04-24 2008-09-24
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Footwear — Test method for slide fasteners — Resistance to
damage during closure under lateral force
Chaussures — Méthode d'essai pour les fermetures éclair — Résistance à l'endommagement sous contrainte
latérale durant la fermeture
ICS 61.060

ISO/CEN PARALLEL ENQUIRY
This draft International Standard is a draft standard developed within the European Committee for
Standardization (CEN) and processed under the CEN-lead mode of collaboration as defined in the
Vienna Agreement. The document has been transmitted by CEN to ISO for circulation for ISO member
body voting in parallel with CEN enquiry. Comments received from ISO member bodies, including those
from non-CEN members, will be considered by the appropriate CEN technical body. Should this DIS be
accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-
month FDIS vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2008

---------------------- Page: 5 ----------------------
ISO/DIS 10749
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2008 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/DIS 10749
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Principle.1
5 Apparatus and materials.
...