SIST EN 1846-2:2002/A1:2005
(Amendment)Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance
Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance
The amendment specifies amended requirements for dimensions ground clearance under axle (h) in clause 5.2.1.1, table 6 and for turning circle between walls (D) in clause 5.2.1.2, table 7 of EN 1846-2:2001.
Feuerwehrfahrzeuge - Teil 2: Allgemeine Anforderungen - Sicherheit und Leistung
Véhicules des services de secours et de lutte contre l'incendie - Partie 2 : Spécifications communes - Sécurité et performances
Gasilska in reševalna vozila – 2. del. Splošne zahteve – Varnost in obnašanje v uporabi
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1846-2:2002/A1:2005
01-februar-2005
Gasilska in reševalna vozila – 2. del. Splošne zahteve – Varnost in obnašanje v
uporabi
Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and
performance
Feuerwehrfahrzeuge - Teil 2: Allgemeine Anforderungen - Sicherheit und Leistung
Véhicules des services de secours et de lutte contre l'incendie - Partie 2 : Spécifications
communes - Sécurité et performances
Ta slovenski standard je istoveten z: EN 1846-2:2001/A1:2004
ICS:
13.220.10 Gašenje požara Fire-fighting
43.160 Vozila za posebne namene Special purpose vehicles
SIST EN 1846-2:2002/A1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1846-2:2002/A1:2005
---------------------- Page: 2 ----------------------
SIST EN 1846-2:2002/A1:2005
EUROPEAN STANDARD
EN 1846-2:2001/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 13.220.10
English version
Firefighting and rescue service vehicles - Part 2: Common
requirements - Safety and performance
Véhicules des services de secours et de lutte contre Feuerwehrfahrzeuge - Teil 2: Allgemeine Anforderungen -
l'incendie - Partie 2 : Spécifications communes - Sécurité et Sicherheit und Leistung
performances
This amendment A1 modifies the European Standard EN 1846-2:2001; it was approved by CEN on 14 October 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1846-2:2001/A1:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1846-2:2002/A1:2005
EN 1846-2:2001/A1:2004 (E)
Foreword
This document (EN 1846-2:2001/A1:2004) has been prepared by Technical Committee CEN/TC 192 “Fire service
equipment”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 1846-2:2001/A1:2004 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by May 2005, and conflicting
national standards shall be withdrawn at the latest by May 2005.
This Amendment has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of an EU Directive.
For relationship with this EU Directive, see informative Annex ZA of EN 1846-2:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
2
---------------------- Page: 4 ----------------------
SIST EN 1846-2:2002/A1:2005
EN 1846-2:2001/A1:2004 (E)
Clause 5
5.2.1.1 Geometric dimensions
Amend in Table 6 the dimensions for ground clearance under axle, h, and add a Table footnote (4) as follows:
Table 6 - Geometric dimensions
Mass class
L (Light) M (Medium) S (Super)
(see EN
2 t < GLM ≤ 7,5 t 7,5 t < GLM ≤ 14 t GLM > 14 t
1846-1:1998)
Category 3 3 3
1 2 1 2 1 2
(see EN (all (all (all
(urban) (rural) (urban) (rural) (urban) (rural)
1846-1:1998) terrain) terrain) terrain)
1)
4) 4)
h (m) ≥ 0,14 ≥ 0,18 ≥ 0,20 ≥ 0,15 ≥ 0,23 ≥ 0,30 ≥ 0,16 ≥ 0,25 ≥ 0,30
4) The fi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.