iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 500-2:2000

(Main)

Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines

Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines

This part of EN 500 specifies the safety requirements for road-milling machines as defined in clause 3 and deals with the significant hazards pertinent to road-milling machines, when used as intended and in conditions foreseen by the manufacturer.

Bewegliche Straßenbaumaschinen - Sicherheit - Teil 2: Besondere Anforderungen an Straßenfräsen

Teil 2 dieser Norm legt die sicherheitstechnischen Anforderungen für Straßenfräsen - wie in Abschnitt 3 definiert - fest, und behandelt die artspezifischen Gefährdungen, die von Straßenfräsen ausgehen, wenn sie bestimmungsgemäß entsprechend den Empfehlungen des Herstellers verwendet werden.

Machines mobiles pour la construction de routes - Sécurité - Partie 2: Exigences spécifiques pour engins de fraisage de chaussée

La partie 2 de cette norme prescrit les exigences de sécurité applicables aux engins de fraisage de chaussée - tels qu'ils sont définis dans l'article 3 - et traite les phénomenes dangereux significatifs résultant des engins de fraisage de chaussée, quand ils sont utilisés normalement et conformément aux recommandations du fabricant.

Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines

General Information

Status
Withdrawn
Publication Date
31-Mar-2000
Withdrawal Date
31-Dec-2006
ICS
93.080.10 - Road construction
Technical Committee
SS SPL - Technical Board for the general field
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jan-2007
Due Date
01-Jan-2007
Completion Date
01-Jan-2007
Directive
89/392/EEC - Machinery - Safety of machinery: general essential health and safety requirements
98/37/EC - Machinery
Mandate
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
EN 500-2:1995 - Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines

Relations

Child
SIST EN 500-3:2000 - Mobile road construction machinery - Safety - Part 3: Specific requirements for soil stabilization machines
Effective Date
22-Dec-2008
Child
SIST EN 500-5:2000 - Mobile road construction machinery - Safety - Part 5: Specific requirements for joint cutters
Effective Date
22-Dec-2008
Child
SIST EN 500-4:2000 - Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines
Effective Date
22-Dec-2008
Child
SIST ENV 500-6:2000 - Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
Effective Date
22-Dec-2008
Replaced By
SIST EN 500-2:2007 - Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines
Effective Date
01-Jan-2007

Buy Standard

EN 500-2:2000EN 500-2:2000
PreviousNext
Standard
EN 500-2:2000
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 500-2:2000
01-april-2000
Mobile road construction machinery - Safety - Part 2: Specific requirements for
road-milling machines
Mobile road construction machinery - Safety - Part 2: Specific requirements for road-
milling machines
Bewegliche Straßenbaumaschinen - Sicherheit - Teil 2: Besondere Anforderungen an
Straßenfräsen
Machines mobiles pour la construction de routes - Sécurité - Partie 2: Exigences
spécifiques pour engins de fraisage de chaussée
Ta slovenski standard je istoveten z: EN 500-2:1995
ICS:
93.080.10 Gradnja cest Road construction
SIST EN 500-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Pag
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13862:2022(Main)
Floor cutting-off machines - Safety
EN 13862:2021

This document applies to pedestrian controlled floor sawing machines having power feed, manual feed or hand feed (see 3.2) for sawing, grooving and milling floor surfaces made of concrete, asphalt and similar mineral building materials where the main power is supplied by electric or internal combustion prime engine. The power transmission of floor sawing machines is mechanical or hydraulic.
This document deals with all significant hazards pertinent to floor sawing machines, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
These machines are designed for use with rotating cutting-off wheels for wet and dry cutting. These cutting-off wheels can be either a diamond cutting-off wheel or a boron nitride cutting-off wheel, according to EN 13236.
This document does not apply to:
-   self-propelled ride-on floor sawing machines;
-   machines moving along a rail;
-   hand-held portable cutting off machines for construction materials mounted on a mobile support, to be used as floor saws;
-   remote controlled machines.
This document covers electrical hazards by making reference to relevant European Standards (see 4.2).
Those hazards that are relevant for all mechanical, electrical, hydraulic and other equipment or machinery and that are dealt with in standards for common use are not covered by this document. Reference to pertinent standards is made where such standards are applicable and so far necessary.
In this document, floor sawing machines are called "machines", and cutting-off wheels are called "tools".
This document applies primarily to machines which are manufactured after the date of approval of the standard by CEN.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 15209:2022(Main)
Tactile paving surface indicators produced from concrete, clay and stone
CEN/TS 15209:2021

This document specifies the method and acceptance criteria for the dimensions for surface profile features and patterns for the surface of pedestrian paving units, used to convey information for visually impaired people. It applies to paving units made of concrete, clay and stone where the tactile profiles are monolithic with the unit.
It does not specify requirements for profile and dimensions of a single tactile paving profile but proposes ranges within which these dimensions should fall. Default dimensions are given which may be used in the absence of a national requirement.
This document proposes methods of measurement of profiles, light reflectance and colour but does not specify requirements for these characteristics. These properties will be decided by the designer taking into account the regulations, codes of practice, and guidance in the place of use of the units.
It does not specify material characteristics.

  • Technical specification
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16165:2021(Main)
Determination of slip resistance of pedestrian surfaces - Methods of evaluation
EN 16165:2021

This document specifies test methods for the determination of the slip resistance of surfaces in the most commonly encountered situations in which pedestrians walk.
NOTE   It is also possible to use this document for measurements where persons might walk on trafficked areas.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13036-5:2019(Main)
Road and airfield surface characteristics - Test methods - Part 5: Determination of longitudinal unevenness indices
EN 13036-5:2019

This European Standard specifies the mathematical processing of digitized longitudinal profile measurements to produce evenness indices. The document describes the calculation procedure for the International Roughness Index (IRI), Root Mean Square (RMS) and Longitudinal Profile Variance (LPV) from three separate wavelength bands and the σWLP and ΔWLP from the Weighted Longitudinal Profile (WLP).
The purpose of this document is to provide a standard practice for calculating and reporting estimates of road evenness from digitized longitudinal profiles. Other aims with the standard are to facilitate the comparison of evenness measurement results carried out with different profiling instruments in European countries.
The evenness range covered in this standard is defined as the wavelength range 0.5 m to 50 m. It should be noted that both shorter and longer wavelengths can also influence the driving comfort but those are not covered in this standard.
The quantified evenness indices derived from the standard are useful support for pavement management systems. The output can also be used for type approval and performance control of new and old pavements. The indices can be used on rigid, flexible and gravel road surfaces.
The standard doesn´t define from what position on the road the longitudinal profile should be obtained.
The derived indices are portable in the sense that they can be obtained from longitudinal profiles measured with a variety of instruments.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13020:2016(Main)
Road surface treatment machines - Safety requirements
EN 13020:2015

This document applies to road surface treatment machines, which are in particular:
- binder sprayers [or sprayers];
- chipping spreaders [or spreaders];
- machines for surface repairs !(binder sprayer chipping spreader [or sprayer spreader]);
- mastics asphalt mixers;
- joint sealer;
- micro-surfacing machines/slurry machines;
(see also Clause 3).
Road surface treatment machines can be mounted on a carrier vehicle, trailer or articulated truck, combining
to form an integral unit. It is also possible to mount a road surface treatment machine on its own chassis
construction and propulsion system (self-propelled or pedestrian-controlled). In all cases the machine and
chassis form an integral unit.
Directives and standards for the vehicular truck chassis aspects, termed 'carrier vehicle' in this document,
would be those relative to that equipment, even where specific modifications have been made to realize the
road surface treatment application. The use in public road traffic is governed by the national regulations.
This document deals with all significant hazards identified through a risk assessment relevant to road surface
treatment machines when they are used as intended and under the conditions foreseen by the manufacturer
(see Clause 4). This document does not deal with significant hazards associated with pressurized tanks, noise
and EMC. This document specifies the appropriate technical measures to eliminate or reduce risks arising
from the significant hazards associated with machine operation, setting and adjustments, load discharge and
routine maintenance.
This document does not include requirements for the carrier vehicles or special constructions. These are
covered in directives related to the construction of vehicles. Demountable bodywork systems (e.g.
demountable containers) are specified in other standards. !Vibrations are not dealt with in the standard,
because for all machines of this family vibration is not a relevant hazard due to the low working speed and
special working conditions (e.g. flat surface).

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 536:2015(Main)
Road construction machines - Mixing plants for road construction materials - Safety requirements
EN 536:2015

This European Standard specifies the safety requirements applicable to stationary and relocatable mixing plants for the production of materials (e.g. hot-mix asphalt, cold-mix asphalt, cement gravel) used for the construction and maintenance of traffic routes (roads, highways, sidewalks, airfields, etc.) water retaining works, dam walls, culverts, etc.
This European Standard applies to the following types of mixing plant:
a)   hot Asphalt mixing plant;
b)   cold mixing plant (e.g. for production of cement gravel, cold mix asphalt);
c)   mixing plant for bituminous or non-bituminous reclaimed materials;
d)   mixing plant for mastic asphalt, also including natural asphalt.
Machines moving during the working process (e.g. mobile mastic asphalt mixers) and crushers are not covered by this European Standard.
Those types of asphalt mixing plants can also be combined or enlarged by additional installations (e.g. Plant for storage of binders (e.g. bituminous, synthetic, vegetal).
This European Standard deals with all significant hazards pertinent to mixing plants, when they are used as intended and under the conditions of misuse which are reasonably foreseen by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
This European Standard does not apply to machines for the production of cement concrete and mortar as covered in EN 12151.
This European Standard does not deal with hazards caused by flammable gases. As soon as information is available it will be included.
This European Standard is not applicable to mixing plants for road construction materials, which are manufactured before the date of publication of this European Standard by CEN.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 15901-15:2014(Main)
Road and airfield surface characteristics - Part 15: Procedure for determining the skid resistance of a pavement surface using a device with longitudinal controlled slip (LFCI): The IMAG
CEN/TS 15901-15:2014

This Technical Specification describes a method only used on airports for determining the skid resistance of pavements by measurement of the longitudinal friction coefficient LFCI.
The method provides a measure of the wet skid resistance properties of a bound surface by measurement of the longitudinal friction coefficient using a trailer with a standard slip ratio of 15 %. The slip ratio can be chosen between 0 % and 100 % for research application.
The test tyre is dragged over a pre wetted pavement under vertical force and constant speed conditions while the test tyre is parallel to the direction of motion.
This Technical Specification covers the operation of the IMAG device.
The skid resistance of a pavement is determined by friction measurements at different speeds. Tests can be performed between 40 km/h and 120 km/h but standard test speeds are 40 km/h, 65 km/h and 95 km/h. Low speed measurements asses the microtexture while high speed measurements asses the macrotexture. The skid resistance is reported as friction measurements at these speeds and by comparison with the minimum friction level.

  • Technical specification
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13036-4:2011(Main)
Road and airfield surface characteristics - Test methods - Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test
EN 13036-4:2011

This European standard describes a method for determining the slip/skid resistance of a surface using a device which remains stationary at the test location. The slip/skid resistance is measured by means of a pendulum arm. The method provides a measure of the slip/skid resistance properties of a surface either in the field or in the
laboratory. This method measures the slip/skid resistance of a small area of a surface (approximately 0,01 m2). This should be considered when deciding its applicability to a surface which may have non-homogeneous surface characteristics, e.g. containing ridges or grooves, or is rough textured (exceeding 1,2 mm patch test).
NOTE 1 As the results from this test are taken at one small location, the results cannot be compared with results from devices e. g. mobile devices, that measure the slip/skid resistance over a long length of a surface. NOTE 2 The accuracy and precision of the test can be affected by the operative. The test should be carried out by a
trained and competent person who has carried out the validation procedure in Annex A.1.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 15901-13:2011(Main)
Road and airfield surface characteristics - Part 13: Procedure for determining the skid resistance of a pavement surface by measurement of a sideway force coefficient (SFCO): the Odoliograph
CEN/TS 15901-13:2011

This document describes a method for determining the wet-road skid resistance of a surface by measurement of a sideway force coefficient SFCO. The method provides a measure of the wet-road skid resistance properties of a bound surface by measurement of sideway-force coefficient at a controlled speed. The method has been developed for use on roads but is also applicable to other paved areas such as airport runways.
This document covers the operation of the Odoliograph. This is a device developed by the Belgian Road Research Centre that uses the side-force principle to make routine, expertise and research measurements of skid resistance continuously on long lengths of road.
A machine conforming to the general characteristics of the Odoliograph designed by the Belgian Road Research Centre and the specific provisions of this document may also be used for the tests.
The skid resistance of a pavement is determined by friction measurements and measurements of pavement texture. Where measurement of pavement texture is required the standard for this measurement and the device is described in EN ISO 13473-1.

  • Standardization document
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 500-4:2011(Main)
Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines
EN 500-4:2011

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This document specifies additional requirements to and/or exceptions from EN 500-1 ”Common requirements”. This part of EN 500 is not applicable for seated ride-on operated rollers with a drum width less than nominal 0,8 m.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day