SIST EN 13523-18:2020
(Main)Coil coated metals - Test methods - Part 18: Resistance to staining
Coil coated metals - Test methods - Part 18: Resistance to staining
This Part of EN 13523 specifies test procedures for assessing the effect of chemicals on the characteristics of an organic coating on a metallic substrate. It covers testing by using defined substances and to assess the change in characteristics such as discoloration, change in gloss, blistering, softening, swelling and loss of adhesion. Assessment of other phenomena may be agreed between the interested parties.
Bandbeschichtete Metalle - Prüfverfahren - Teil 18: Beständigkeit gegen Fleckenbildung
Dieses Dokument legt Verfahren fest, mit denen der Einfluss von Chemikalien auf die Eigenschaften einer organischen Beschichtung auf einem metallischen Substrat abgeschätzt werden kann. Es schließt die Prüfung mit definierten Substanzen und die Bewertung von Eigenschaftsänderungen wie Verfärbung, Glanz¬änderung, Blasenbildung, Erweichen, Quellen und Haftfestigkeitsverlust ein. Andere Phänomene können nach Vereinbarung zwischen den Vertragspartnern bewertet werden.
Tôles prélaquées - Méthodes d'essai - Partie 18 : Résistance aux taches
Le présent document spécifie des modes opératoires d’essai pour évaluer l’incidence des produits chimiques sur les caractéristiques d’un revêtement organique appliqué sur un subjectile métallique. Il couvre les essais effectués avec des substances définies afin d’évaluer les changements de caractéristiques (décoloration, changement de brillant, cloquage, ramollissement, gonflement et perte d’adhérence). L’évaluation d’autres phénomènes peut faire l’objet d’un accord entre les parties intéressées.
Prevlečene kovine, ki se navijajo - Preskusne metode - 18. del: Odpornost proti nastanku madežev
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13523-18:2020
01-september-2020
Nadomešča:
SIST EN 13523-18:2003
Prevlečene kovine, ki se navijajo - Preskusne metode - 18. del: Odpornost proti
nastanku madežev
Coil coated metals - Test methods - Part 18: Resistance to staining
Bandbeschichtete Metalle - Prüfverfahren - Teil 18: Beständigkeit gegen Fleckenbildung
Tôles prélaquées - Méthodes d'essai - Partie 18 : Résistance aux taches
Ta slovenski standard je istoveten z: EN 13523-18:2020
ICS:
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-18:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13523-18:2020
---------------------- Page: 2 ----------------------
SIST EN 13523-18:2020
EN 13523-18
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-18:2002
English Version
Coil coated metals - Test methods - Part 18: Resistance to
staining
Tôles prélaquées - Méthodes d'essai - Partie 18 : Bandbeschichtete Metalle - Prüfverfahren - Teil 18:
Résistance aux taches Beständigkeit gegen Fleckenbildung
This European Standard was approved by CEN on 3 May 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-18:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13523-18:2020
EN 13523-18:2020 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 5
6 Substances . 6
7 Sampling . 6
8 Test panels . 6
9 Procedure. 6
9.1 General . 6
9.2 Spot test (covered) . 6
9.3 Spot test (open) . 7
9.4 Immersion test . 7
10 Expression of results . 7
11 Precision . 7
12 Test report . 8
Bibliography . 9
2
---------------------- Page: 4 ----------------------
SIST EN 13523-18:2020
EN 13523-18:2020 (E)
European foreword
This document (EN 13523-18:2020) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2020, and conflicting national standards shall be
withdrawn at the latest by December 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-18:2002.
The main changes are:
a) the required supplementary information (former Clause 10) has been integrated in the test report;
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 15: Metamerism
3
---------------------- Page: 5 ----------------------
SIST EN 13523-18:2020
EN 13523-18:2020 (E)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republ
...
SLOVENSKI STANDARD
oSIST prEN 13523-18:2019
01-julij-2019
Prevlečene kovine, ki se navijajo - Preskusne metode - 18. del: Odpornost proti
nastanku madežev
Coil coated metals - Test methods - Part 18: Resistance to staining
Bandbeschichtete Metalle - Prüfverfahren - Teil 18: Beständigkeit gegen Fleckenbildung
Tôles prélaquées - Méthodes d'essai - Partie 18 : Résistance aux taches
Ta slovenski standard je istoveten z: prEN 13523-18
ICS:
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-18:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-18:2019
---------------------- Page: 2 ----------------------
oSIST prEN 13523-18:2019
DRAFT
EUROPEAN STANDARD
prEN 13523-18
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2019
ICS 25.220.60 Will supersede EN 13523-18:2002
English Version
Coil coated metals - Test methods - Part 18: Resistance to
staining
Tôles prélaquées - Méthodes d'essai - Partie 18 : Bandbeschichtete Metalle - Prüfverfahren - Teil 18:
Résistance aux taches Beständigkeit gegen Fleckenbildung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-18:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-18:2019
prEN 13523-18:2019 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 5
6 Substances . 6
7 Sampling . 6
8 Test panels . 6
9 Procedure. 6
9.1 General . 6
9.2 Spot test (covered) . 6
9.3 Spot test (open) . 7
9.4 Immersion test . 7
10 Expression of results . 7
11 Precision . 7
12 Test report . 8
Bibliography . 9
2
---------------------- Page: 4 ----------------------
oSIST prEN 13523-18:2019
prEN 13523-18:2019 (E)
European foreword
This document (prEN 13523-18:2019) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-18:2002.
The main changes are:
a) the required supplementary information (former Clause 10) has been integrated in the test report;
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 15: Metamerism
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
3
---------------------- Page: 5 ----------------------
oSIST prEN 13523-18:2019
prEN 13523-18:2019 (E)
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
4
--
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.