iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 13523-10:2024

(Main)

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

This part of the EN 13523 series specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung mit Leuchtstofflampen und Kondensation von Wasser

Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV fluorescent et à la condensation de l'eau

Le présent document spécifie les principes de base et le mode opératoire à appliquer pour déterminer la résistance d’un revêtement organique appliqué sur un support métallique (prélaquage en bandes continues), à une combinaison d’un rayonnement UV fluorescent, de condensation d’eau et de température, dans des conditions contrôlées.
Compte tenu des diverses conditions qui règnent pendant le processus de vieillissement naturel et de la nature extrême des essais accélérés, aucune corrélation ne peut être escomptée entre les deux.
Tous les revêtements organiques ne se comporteront pas de la même manière, mais un certain degré de corrélation peut apparaître entre ceux de même type générique.

Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti fluorescentni ultravijolični svetlobi in kondenzaciji vode

Ta del skupine standardov EN 13523 določa osnovna načela in postopek za ugotavljanje odpornosti organske prevleke na kovinski podlagi (prevlečene kovine, ki se navijajo) proti kombinaciji fluorescentne ultravijolične svetlobe ter kondenzacije vode in temperature pod nadzorovanimi pogoji.
Zaradi različnih pogojev, ki jih ustvarijo naravne vremenske razmere, in ekstremne narave pospešenega preskušanja korelacije med njimi ni mogoče pričakovati.
Vse organske prevleke ne bodo učinkovale na enaki osnovi, vendar določena stopnja korelacije med isto generično vrsto je lahko prisotna.

General Information

Status
Published
Public Enquiry End Date
02-Oct-2023
Publication Date
11-Aug-2024
ICS
17.180.20 - Colours and measurement of light
25.220.60 - Organic coatings
Technical Committee
IBLP - Paints and varnishes
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Jun-2024
Due Date
22-Aug-2024
Completion Date
12-Aug-2024
Ref Project
EN 13523-10:2024 - Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

Relations

Replaces
SIST EN 13523-10:2017 - Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
Effective Date
01-Sep-2024

Buy Standard

EN 13523-10:2024EN 13523-10:2024
PreviousNext
Standard
EN 13523-10:2024
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2024
Nadomešča:
SIST EN 13523-10:2017
Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti
fluorescentni ultravijolični svetlobi in kondenzaciji vode
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and
water condensation
Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung
mit Leuchtstofflampen und Kondensation von Wasser
Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV
fluorescent et à la condensation de l'eau
Ta slovenski standard je istoveten z: EN 13523-10:2024
ICS:
17.180.20 Barve in merjenje svetlobe Colours and measurement of
light
25.220.60 Organske prevleke Organic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13523-10
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2024
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-10:2017
English Version
Coil coated metals - Test methods - Part 10: Resistance to
fluorescent UV radiation and water condensation
Tôles prélaquées - Méthodes d'essai - Partie 10 : Bandbeschichtete Metalle - Prüfverfahren - Teil 10:
Résistance à un rayonnement UV fluorescent et à la Beständigkeit gegen UV-Strahlung mit
condensation de l'eau Leuchtstofflampen und Kondensation von Wasser
This European Standard was approved by CEN on 1 January 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-10:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure . 6
8.1 Exposure . 6
8.2 Calibration and maintenance of calibration . 7
8.3 Evaluation of test specimens . 7
9 Expression of results . 8
10 Precision . 8
11 Test report . 8
Bibliography . 9

European foreword
This document (EN 13523-10:2024) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2024, and conflicting national standards shall
be withdrawn at the latest by October 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-10:2017.
10:2017:
a) in 8.1 the test duration has been aligned with EN 1396 and EN 10169;
b) in 8.3 wider range of observations have been included;
c) in Clause 9 the test method has been aligned to new coating categories defined in EN 10169;
d) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Ro
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13523-3:2024(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
EN 13523-3:2024

This document specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.
When two colour specimens have identical spectral reflectance curves, they are matching under any illuminant irrespective of its spectral characteristics. This is termed a “spectral match”. It is also possible for two colour specimens having different spectral reflectance curves to match visually under a given light source but not to match under another light source with different spectral characteristics; such matches are termed “metameric”.
One quantitative description of metamerism is the so-called “metamerism index”.
Information on the metamerism index is of limited value where ΔE (instrumental colour difference for a given illuminant) is > 0,5. The metamerism index is not suited for determining the absolute colour difference or colour consistency of a given specimen at change of illuminant.
The colour difference under the reference illuminant is to be measured in colour coordinates L*, a* and b*.
Excluded from this method are organic coatings producing fluorescence and/or which are multicoloured, pearlescent or metallic.
Establishing a reference as well as the magnitude of an acceptable colour difference are not covered by this method.
Two methods are given in this document:
a)   instrumental colour difference measurement using a tristimulus colourimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
It is advised that care is taken when measuring e.g.
—   textured surfaces;
—   fluorescent coatings;
—   metameric coatings;
—   multi-coloured, pearlescent, metallic or special colour effect coatings.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-22:2024(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
EN 13523-22:2024

This part of the EN 13523 series specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE   Results might differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523 15).
If a metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-23:2023(Main)
Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide
EN 13523-23:2023

This Part of EN 13523 describes the procedure for determining the colour stability of an organic coating on a metallic substrate when exposed to humid atmospheres containing sulfur dioxide. This method has been designed to provide an accelerated test for evaluating the colour fastness of coil coated products in atmospheres containing sulfur dioxide (typical of industrial atmospheres).

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-3:2024(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
EN 13523-3:2024

This document specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.
When two colour specimens have identical spectral reflectance curves, they are matching under any illuminant irrespective of its spectral characteristics. This is termed a “spectral match”. It is also possible for two colour specimens having different spectral reflectance curves to match visually under a given light source but not to match under another light source with different spectral characteristics; such matches are termed “metameric”.
One quantitative description of metamerism is the so-called “metamerism index”.
Information on the metamerism index is of limited value where ΔE (instrumental colour difference for a given illuminant) is > 0,5. The metamerism index is not suited for determining the absolute colour difference or colour consistency of a given specimen at change of illuminant.
The colour difference under the reference illuminant is to be measured in colour coordinates L*, a* and b*.
Excluded from this method are organic coatings producing fluorescence and/or which are multicoloured, pearlescent or metallic.
Establishing a reference as well as the magnitude of an acceptable colour difference are not covered by this method.
Two methods are given in this document:
a)   instrumental colour difference measurement using a tristimulus colourimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
It is advised that care is taken when measuring e.g.
—   textured surfaces;
—   fluorescent coatings;
—   metameric coatings;
—   multi-coloured, pearlescent, metallic or special colour effect coatings.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-22:2024(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
EN 13523-22:2024

This part of the EN 13523 series specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE   Results might differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523 15).
If a metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-23:2023(Main)
Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide
EN 13523-23:2023

This Part of EN 13523 describes the procedure for determining the colour stability of an organic coating on a metallic substrate when exposed to humid atmospheres containing sulfur dioxide. This method has been designed to provide an accelerated test for evaluating the colour fastness of coil coated products in atmospheres containing sulfur dioxide (typical of industrial atmospheres).

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 23936-4:2024(Main)
Oil and gas industries including lower carbon energy - Non-metallic materials in contact with media related to oil and gas production - Part 4: Fiber-reinforced composite (ISO 23936-4:2024)
EN ISO 23936-4:2024

This document presents general principles and gives requirements and recommendations for the
assessment of stability of non-metallic materials for service in equipment used in oil and gas production
environments. This information aids in material selection. It can be applied to help avoid costly degradation failures of the equipment itself, which could pose a risk to the health and safety of the public and personnel or the environment. It supplements but does not replace, the material requirements given in the appropriate design codes, standards or regulations.
This document describes the procedures for comparative testing of polymeric composite materials consisting of polymers (thermoplastics and thermosets) and re-enforcing materials e. g. glass, carbon, aramid or metals as continuous fibres or woven fabric used in equipment for oil and gas production. The compounded particulate- and short fibre-reinforced composites have been included in ISO 23936-1 and ISO 23936-3.
Mechanical properties and the environmental stability of composite materials depend on the properties and environmental stability of matrix resins, fibres and fibre/resin bonding interfaces. This document focuses on the overall composite properties and their environmental stability. To permit this assessment this document utilizes flat plates and/or tubular shapes made specifically for these tests. Testing and characterization of neat resins and fibre products are beyond this scope.
The equipment considered includes, but is not limited to, non-metallic pipelines, piping, liners and downhole tool components.
Blistering by rapid gas decompression is not included in the scope of this document.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN ISO/TS 80004-13:2024(Main)
Nanotechnologies - Vocabulary - Part 13: Graphene and other two-dimensional (2D) materials (ISO/TS 80004-13:2024)
CEN ISO/TS 80004-13:2024

ISO/TS 80004-13:2017 lists terms and definitions for graphene and related two-dimensional (2D) materials, and includes related terms naming production methods, properties and their characterization.
It is intended to facilitate communication between organizations and individuals in research, industry and other interested parties and those who interact with them.

  • Technical specification
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 4641-401:2024(Main)
Aerospace series - Cables, optical 125 μm diameter cladding - Part 401: Tight structure bend insensitive 50 µm/125 µm GI fibre nominal, 1,8 mm outside diameter - Product standard
EN 4641-401:2024

This document specifies the general characteristics, conditions for qualification, acceptance and quality assurance for a fibre optic cable with a bend-insensitive, 50 µm/125 µm Graded Index fibre core, 1,8 mm outside diameter for non pull-proof contact designs.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 9300-001:2024(Main)
Aerospace series - LOTAR - Long Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data - Part 001: Structure
EN 9300-001:2024

This document defines the structure and content for the long-term preservation of digital product and technical data. EN 9300 is broken into a series of separate standard parts to make the standard applicable for different business requirements and extensible for further long-term archiving formats.
The following outlines the total scope of this document:
For the purpose of this document, structure, and content of EN 9300 standard parts are detailed.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day