SIST EN 13862:2002
(Main)Floor cutting-off machines - Safety
Floor cutting-off machines - Safety
This European Standard applies to self-propelled ride-on1) and pedestrian controlled floor sawing machines having power feed, manual feed or hand feed (see 3.2) for sawing, grooving and milling floor surfaces made of concrete, asphalt and similar mineral building materials where the main power is supplied by electric or internal combustion prime engine. The power transmission of floor sawing machines is mechanical or hydraulic.
This European Standard deals with all significant hazards pertinent to floor sawing machines, when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
These machines are designed for use with rotating cutting-off wheels for wet and dry cutting. These cutting-off wheels can be either a diamond cutting-off wheel or a boron nitride cutting-off wheel.
NOTE Other types of cutting tools may also be used provided that they fall within the design and usage parameters of the machine. This standard does not cover this.
This European Standard does not apply to:
- machines moving along a rail;
- hand-held portable cutting off machines for construction materials mounted on a mobile support, to be used as floor saws;
- remote controlled machines.
This European Standard covers electrical hazards by making reference to relevant European Standards (see 5.2).
Those hazards that are relevant for all mechanical, electrical, hydraulic and other equipment or machinery and that are dealt with in standards for common use are not covered by this European Standard. Reference to pertinent standards is made where such standards are applicable and so far necessary.
In this European Standard, floor sawing machines are called "machines", and cutting-off wheels are called "tools".
This European Standard applies primarily to machines which are manufactured after the date of approval
Bodentrennschleifmaschinen - Sicherheit
Diese Europäische Norm gilt für selbstfahrende Bodentrennschleifmaschinen mit aufsitzendem Bediener1) und mitgängergeführte Bodentrennschleifmaschinen mit maschinellem Vorschub, manuellem Vorschub oder Vorschub von Hand (siehe 3.2) zum Sägen, Einbringen von Rillen und Fräsen von Bodenoberflächen aus Beton, Asphaltbitumen und ähnlichen mineralischen Baumaterialien, wobei die Hauptantriebsenergie durch einen Elektro-, oder Verbrennungsmotor zur Verfügung gestellt wird. Die Kraftübertragung bei Bodentrennschleifmaschinen ist mechanisch oder hydraulisch.
Diese Europäische Norm behandelt alle signifikanten Gefährdungen, die auf Bodentrennschleifmaschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den Empfehlungen des Herstellers verwendet werden (siehe Abschnitt 4). Diese Europäische Norm spezifiziert die entsprechenden technischen Maßnahmen zur Beseitigung oder Verminderung der Risiken, die von den signifi-kanten Gefährdungen ausgehen.
Diese Maschinen werden mit rotierenden Trennscheiben im Nass- und Trockenschnitt betrieben. Diese Trenn-scheiben können entweder eine Diamanttrennscheibe oder eine Bornitridtrennscheibe sein.
ANMERKUNG Andere Arten von Werkzeugen können auch verwendet werden, insofern diese entsprechend der Maschinen-konstruktion und der bestimmungsgemäßen Verwendung der Maschine geeignet sind. Diese Norm berücksichtigt andere Arten von Werkzeugen jedoch nicht.
Diese Europäische Norm gilt nicht für:
3 Maschinen, die auf einer Schiene fahren;
3 auf einer mobilen Tragvorrichtung montierte handgeführte, tragbare Trennmaschinen für Baumaterialien, die als Bodensägen verwendet werden;
3 ferngesteuerte Maschinen.
Diese Europäische Norm behandelt elektrische Gefährdungen durch Verweis auf relevante Euro-päische Normen (siehe 5.2).
Machines a scier les sols - Sécurité
Cette norme européenne s'applique aux machines de chantier a scier, rainurer et meuler les sols en béton, asphalte bitumineux et matériaux similaires automotrices a conducteur porté ) ou a conducteur accompagnant a avance automatique, poussées ou manuelles (voir 3.2), pour lesquelles l'énergie principale est fournie par un moteur électrique ou thermique. La transmission de d'énergie des scies a sol est mécanique ou hydraulique.
Cette norme européenne traite de tous les phénomenes dangereux significatifs spécifiques aux machines a scier les sols lorsqu'elles sont utilisées normalement et dans les conditions prévues par le constructeur (voir article 4). Cette norme spécifie les mesures techniques appropriées pour éliminer ou réduire les risques dus aux phénomenes dangereux significatifs.
Ces machines sont conçues pour etre utilisées avec des disques a tronçonner par arrosage ou a sec. Ces disques a tronçonner et qui peuvent etre notamment des meules a tronçonner soit des disques a tronçonner a base de diamant ou de nitrure de bore.
NOTE D'autres types d'outils peuvent également etre utilisés suivant les caractéristiques de la machine et le travail pour lequel elle a été conçue, mais la présente norme ne couvre pas ces cas.
Ne sont pas couvertes par cette norme européenne :
3 les machines mobiles sur un rail ;
3 les machines portatives a tronçonner les matériaux montées sur un support mobile pour etre utilisées en scies a sols ;
3 machines commandées a distance.
Cette norme couvre les risques d'origine électrique par référence aux normes européennes (voir 5.2).
Floor cutting-off machines - Safety
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Floor cutting-off machines - SafetyBodentrennschleifmaschinen - SicherheitMachines a scier les sols - SécuritéFloor cutting-off machines - Safety93.080.10Gradnja cestRoad constructionICS:Ta slovenski standard je istoveten z:EN 13862:2001SIST EN 13862:2002en01-januar-2002SIST EN 13862:2002SLOVENSKI
STANDARDSIST EN 500-5:20001DGRPHãþD
SIST EN 13862:2002
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13862September 2001ICS 91.220Supersedes EN 500-5:1995English versionFloor cutting-off machines - SafetyMachines à scier les sols - SécuritéBodentrennschleifmaschinen - SicherheitThis European Standard was approved by CEN on 25 July 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13862:2001 ESIST EN 13862:2002
EN 13862:2001 (E)2ContentsPageForeword.30Introduction.41Scope.42Normative references.53Terms and definitions.63.1Floor sawing machine.63.2Types of machines.63.3Parts of a floor sawing machine.63.4Cutting head.83.5Rated spindle speed.83.6Tool(s).83.7Tool flange.83.8Tool guard.83.9Nominal mass.83.10Maximum operating mass.84List of significant hazards.95Safety requirements and/or measures.105.1Mechanical hazards.105.2Electrical hazards.145.3Thermal hazards.155.4Exhaust fumes (and gas).155.5Machines having a hydraulic power transmission.155.6Fluid containers.165.7Water supply and dust emission.165.8Rotational speed.165.9Noise.165.10Maintenance.176Verification of safety requirements and/or measures.177Information for use.177.1Marking.177.2Accompanying documents.18Annex A (normative)
Noise test code - Grade 2 of accuracy.22Annex B (normative)
Dimensions of the flanges for cutting-off diamond wheels.25Annex C (normative)
Strength of the guards - State of the art concerning thecharacteristics of guards used with cutting-off wheels.27Annex D (normative)
Pictograms.31Annex E (normative)
Verification of surface temperature.33Annex ZA (informative)
Relationship of this document with EC Directives.34Bibliography.35SIST EN 13862:2002
EN 13862:2001 (E)3ForewordThis European Standard has been prepared by Technical Committee CEN/TC 151"Construction equipment and building material machines - Safety", the secretariat of which isheld by DIN.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by March 2002, and conflicting nationalstandards shall be withdrawn at the latest by March 2002.This European Standard replaces EN 500-5:1995.This European Standard has been prepared under a mandate given to CEN by the EuropeanCommission and the European Free Trade Association and supports essential requirements ofEU Directive(s).For relationship with EU Directives, see informative annex ZA, which is an integral part of thisstandard.The annex A is normative and contains "Noise test code - Grade 2 of accuracy", annex B isnormative and contains "Dimensions of the flanges for cutting-off diamond wheels", annex C isnormative and contains "Strength of guards - State of the art concerning the characteristics ofguards used with cutting-off wheels", annex D is normative and contains „Pictograms“, the an-nex E is normative and contains „Verification of surface temperature“ and the annex ZA is in-formative and contains „Relationship of this document with EC Directives“.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.SIST EN 13862:2002
EN 13862:2001 (E)40IntroductionThis European standard is a Type C-standard as stated in EN 292.The machinery concerned and the extent to which hazards are covered are indicated in thescope of this European Standard.1ScopeThis European Standard applies to self-propelled ride-on1) and pedestrian controlled floorsawing machines having power feed, manual feed or hand feed (see 3.2) for sawing, groovingand milling floor surfaces made of concrete, asphalt and similar mineral building materialswhere the main power is supplied by electric or internal combustion prime engine. The powertransmission of floor sawing machines is mechanical or hydraulic.This European Standard deals with all significant hazards pertinent to floor sawing machines,when they are used as intended and under the conditions foreseen by the manufacturer (seeclause 4). This European Standard specifies the appropriate technical measures to eliminate orreduce risks arising from the significant hazards.These machines are designed for use with rotating cutting-off wheels for wet and dry cutting.These cutting-off wheels can be either a diamond cutting-off wheel or a boron nitride cutting-offwheel.NOTE Other types of cutting tools may also be used provided that they fall within the designand usage parameters of the machine. This standard does not cover this.This European Standard does not apply to:-machines moving along a rail;- hand-held portable cutting off machines for construction materials mounted on a mobilesupport, to be used as floor saws;- remote controlled machines.This European Standard covers electrical hazards by making reference to relevant EuropeanStandards (see 5.2).Those hazards that are relevant for all mechanical, electrical, hydraulic and other equipment ormachinery and that are dealt with in standards for common use are not covered by thisEuropean Standard. Reference to pertinent standards is made where such standards areapplicable and so far necessary.
1 ) Specific requirements related to the operator´s station and the mobility of ride-on machines will beadded later on by an amendment.SIST EN 13862:2002
EN 13862:2001 (E)5In this European Standard, floor sawing machines are called "machines", and cutting-off wheelsare called “tools”.This European Standard applies primarily to machines which are manufactured after the date ofapproval of the standard by CEN.2Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisionsof any of these publications apply to this European Standard only when incorporated in it byamendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).EN 292-1:1991Safety of machinery - Basic concepts, general principles for design -Part 1: Basic terminology, methodologyEN 292-2:1991Safety of machinery - Basic concepts, general principles for design -Part 2: Technical principles and specificationsEN 294:1992Safety of machinery - Safety distances to prevent danger zones be-ing reached by the upper limbsEN 563:1994Safety of machinery - Temperatures of touchable surfaces - Ergo-nomics data to establish temperature limit values for hot surfacesEN 953:1997Safety of machinery – Guards - General requirements for the designand construction of fixed and movable guardsEN 954-1:1996Safety of machinery - Safety related parts of control systems - Part 1:General principles of designEN 982:1996Safety of machinery - Safety requirements for fluid power systemsand their components - HydraulicsEN 1070:1998Safety of machinery – TerminologyprEN 13218:1998Machine tools – Safety – Stationary grinding machinesEN 60204-1:1997Safety of machinery - Electrical equipment of machines - Part 1:General requirements (IEC 60204-1:1997)EN 60335-1:1994Safety of household and similar electrical appliances - Part 1:General requirements (IEC 60335-1:1991, modified)EN 60335-2-41:1996Safety of household and similar electrical appliances – Part 2:Particular requirements for pumps for liquids having a temperaturenot exceeding 35 °C (IEC 60335-2-41:1996)EN 60529:1991Degrees of protection provided by enclosures (IP code) (IEC60529:1989)EN 61029-1:1995Safety of transportable motor operated electric tools - Part 1: Generalrequirements (IEC 61029-1:1990, modified)SIST EN 13862:2002
EN 13862:2001 (E)6EN ISO 3744:1995Acoustics - Determination of sound power levels of noise sourcesusing sound pressure - Engineering method in an essentially freefield over a reflecting plane (ISO 3744:1994)EN ISO 11201:1995Acoustics - Noise emitted by machinery and equipment - Measure-ment of emission sound pressure levels at the work station and atother specified positions - Engineering method in an essentially freefield over a reflecting plane (ISO 11201:1995)ISO 525:1999Bonded abrasive products - General requirementsISO 6104:1979Abrasive products - Diamond or cubic boron nitride grinding wheelsand saws - General survey, designation and multilingual nomencla-tureISO 6395:1988Acoustics - Measurement of exterior noise emitted by earth-movingmachinery - Dynamic test conditionsISO 7000:1989Graphical symbols for use on equipment - Index and synopsis3Terms and definitionsFor the purposes of this European Standard the terms and definitions stated in EN 1070:1998apply. Additional terms and definitions specifically needed for this European Standard areadded below.3.1Floor sawing machineMobile machine used on sites, designed for sawing, grooving and grinding ground surfacesmade of concrete, asphalt and similar mineral building materials which is ride-on operated orpedestrian controlled3.2Types of machinesFloor sawing machines may be of the following types:3.2.1Hand feed machineMachine in which the feed movement is effected by the pushing action of the operator3.2.2Machine with manual feed by mechanical meansMachine in which the feed movement is effected by manual operation of a crank or wheel3.2.3Self-propelled machineMachine whose feed movement is obtained by a power source via mechanical or hydraulicpower transmission. Self-propelled machines are ride-on operated or pedestrian controlled3.3Parts of a floor sawing machineA floor sawing machine generally comprises the parts shown in figure 1SIST EN 13862:2002
EN 13862:2001 (E)7Key1Frame2Electric motor, or internal combustion engine which generates the power for driving thetool(s) and which generates the power for the feeding movement to the machine (forself propelled machines)3Tool(s) (illustrated as a cutting-off wheel)4Control devices for the functions and feed of the machine5Guards limiting the hazard of contact in dangerous areas6Water supply system for cooling the diamond cutting-off wheel(s)7Sawing guiding device of the machine (when necessary)NOTE Figure 1 is an example of one of the many machines available for floor sawing, groovingand milling. It illustrates the main components in its construction.Figure 1 - Typical example of a pedestrian controlled floor sawing machineSIST EN 13862:2002
EN 13862:2001 (E)83.4Cutting headAssembly comprising the power unit, the rotating tool(s) and its fixing attachment. It may be in-tegral to the frame of the machine or the drive unit which causes forward movement of the ma-chine along the ground, in order to perform sawing, grooving or milling operation3.5Rated spindle speedSpeed of the drive spindle, in revolutions per minute (min-1) at the rated conditions specified bythe machine manufacturer without cutting-off wheel(s) and under no load3.6Tool(s)Rotating abrasive tool(s) which perform(s) the cutting operation. The tool(s) is(are) (a) rotating(segmented) diamond cutting-off wheel or (an) abrasive cutting-off reinforced bonded wheel(s)type 41 according to ISO 525:1999 and ISO 6104:1979NOTE Other types of abrasive wheels may also be mounted either alone or as several unitstogether according to the design and usage parameters of the machine.3.7Tool flangeMounting device including several parts which securely hold and position the rotating tool/toolson the drive spindle3.8Tool guardGuard which encloses the non-working part of the rotating tool3.9Nominal massThe mass of the machine equipped with all its dismountable parts, but without the tool(s)mounted, the attached tank(s) being empty3.10Maximum operating massThe mass of the machine equipped with all its dismountable parts, ready for use, with thetool(s) mounted and the attached tank(s) being fullSIST EN 13862:2002
EN 13862:2001 (E)94List of significant hazardsThis clause contains all significant hazards and hazardous situations, as far as they are dealtwith in this European Standard, identified by risk assessment significant for this type of machin-ery and which require action to eliminate or reduce risk.Table 1 - List of significant hazardsHazardsConcerned subclauses4.1Hazards due to mass and velocity (kinetic energy ofelements in controlled and uncontrolled motion) ofthe tool5.1.34.2Hazards due to inadequacy of mechanical strengthof the tool5.1.34.3Crushing hazard5.1.2, 5.1.3, 5.1.4, 5.1.5, 5.1.6,5.1.7, 5.1.8, 5.1.9, 7.24.4Shearing hazard5.1.2, 5.1.3, 5.1.5, 5.1.6, 5.1.8,5.1.94.5Cutting and severing hazard5.1.1, 5.1.2, 5.1.3, 5.1.5, 5.1.6,5.1.8, 5.1.94.6Entanglement hazard5.1.2, 5.1.3, 5.1.6, 5.1.8, 5.1.94.7Drawing-in or trapping hazard5.1.2, 5.1.3, 5.1.6, 5.1.8, 5.1.94.8Impact hazard5.1.2, 5.1.3, 5.1.5, 5.1.6, 5.1.7,5.1.8, 5.1.9, 7.24.9Friction or abrasion hazard5.1.2.3, 7.24.10Fluid ejection hazard5.54.11Hazards caused by ejection of parts(material/work pieces)5.1.2, 5.1.3, 5.1.6,5.1.7, 5.84.12Excessive speed of pedestrian controlledmachinery5.1.8.34.13Hazards caused by loss of stability (machinery andmachine parts)5.1.4, 7.24.14Slip, trip and fall hazard in relationship with machin-ery5.6, 7.24.15Hazards caused by electrical contact direct or indi-rect5.2, 7.24.16Hazards resulting in burns and/or scalds, by possi-ble contact of persons, by flames or explosions andalso by radiation of heat sources5.3, 7.24.17Hazards generated by noise5.9, 7.24.18Hazards resulting from contact with or inhalation ofharmful fluids, gases, mists, fumes and dusts5.4, 5.6, 5.7, 7.24.19Hazards caused by fire and/or explosion7.24.20Hazards from the engine and batteries5.4, 5.6, 7.24.21Unauthorized start-up5.1.8.34.22Unhealthy postures or excessive efforts5.1.5, 5.1.8, 7.24.23Hazards caused by inadequate local lighting7.24.24Hazards caused by human errors7.1, 7.24.25Hazard combinations5, 7.1, 7.2(continued)SIST EN 13862:2002
EN 13862:2001 (E)10Table 1 - List of significant hazards (concluded)HazardsConcerned subclauses4.26Hazard caused by failure of energy supply (ofenergy and/or control circuits)5.1.9, 5.2, 7.24.27Hazards caused by failure/disorder of control sys-tem5.1.8.1, 5.1.9, 5.2, 7.24.28Inadequate design of manual controls and theirmode of operation5.1.74.29Hazards caused by errors of fitting5.1.6, 7.1, 7.24.30Hazards caused by temporarily missing and/orincorrectly positioned safety relatedmeasures/means such as:4.30.1Guards of all kinds7.24.30.2Safety related protection devices of all kinds7.24.30.3Starting and stopping devices5.1.8.2, 7.24.30.4Safety signs and tags7.1 , 7.24.30.5Information and warning devices of all kinds7.1 , 7.24.30.6Insufficient instructions for the driver/operator7.24.30.7Essential equipment and accessories for safeadjustment and/or maintenance7.25Safety requirements and/or measuresMachinery shall comply with the safety requirements and/or measures of this clause and in ad-dition with EN 292-1:1991 and EN 292-2:1991 for hazards relevant but not significant which arenot dealt with in this standard.For the application of EN 294:1992, EN 953:1997, EN 982:1996 and EN 60204-1:1997 themanufacturer shall carry out an adequate risk assessment of their requirements, where it isnecessary to make choices.NOTE This specific risk assessment should be part of the general risk assessment relating tothe hazards not covered by this standard.Covering each significant individual hazard is sufficient for covering combinations of hazards.5.1Mechanical hazards5.1.1GeneralAs components and parts have to be manually handled, all the accessible parts, the tool ex-cepted, shall not present sharp edges or angles/corners which could generate hazards whensetting, using, handling, and maintaining the machine. Burrs resulting from, for example,manufacturing, casting or welding shall be eliminated and sharp edges shall be smoothed.5.1.2Protection against moving parts5.1.2.1Transmission partsRotating transmission parts, for example drive shafts, couplings, belt drives shall be providedwith fixed guards to prevent contact. These guards shall comply with EN 953:1997 in particularSIST EN 13862:2002
EN 13862:2001 (E)11clauses 5, 6 and 7. Fixed guards shall be held in position either by welding or by mounting themin such a way that they can be opened or removed only with the aid of tools or keys.Guards shall comply with the provisions of EN 294:1992 on safety distances.When daily access is required for service or maintenance purposes instead of fixed guardsmovable guards type A (see 1.4.2.2 of annex A of EN 292-2:1991) may be fitted. They shallfulfil the following requirements:-they shall remain fixed to the machine when open;-they shall be fitted with a system holding them in the open position;NOTE The system may be, for example, a locking, latching or spring loaded type.5.1.2.2Connection between the cutting head and the frameWhen the vertical movement of the cutting head with respect to the frame is power driven,safety distances according to EN 294:1992 shall be provided.5.1.2.3Protection of the tool5.1.2.3.1GeneralMachines shall be equipped with a guard covering at least the upper half of the tool(s)
and itsfixing device(s) (see figure C.1).Specifications concerning the strength of the guards are given in annex C.The guard(s) shall be so designed to facilitate safe and easy access for tool replacement.When the tool guard is removable to allow access to the tool fixing device, the machine shall beso designed that the rotation of the tool(s) may not be possible without the guard. The followingexception is possible.The presence of a device for stopping the tool(s) is not necessary when the absence or theopening of the guard creates a projection of water, which prevents the intended use of themachine. The guard shall remain fixed to the machine also in the open position and a warningsign (see figure D.3) shall be provided at the guard.5.1.2.3.2Open parts in the guardWhen the guard is designed with a section which can be opened at the front in order to visuallyposition the rotating tool in relation with the cutting line, or to allow it to perform a cut close to avertical surface, then:-the open section shall stay connected to the main guard;-the retaining device of the rotating tool(s) shall remain covered.SIST EN 13862:2002
EN 13862:2001 (E)125.1.2.3.3Complementary requirements to prevent contact with the tool(s) out of the cuttingareaContact with the tool(s) in rotation during the displacement of the machine outside the cuttingarea shall be prevented as follows:-either all parts of the tool(s) (in particular the lower part) shall be guarded when the ma-chine is set for displacement or;- if the tool(s) is(are) not completely guarded, the machine shall be designed to allow dis-placement without the tool rotating, for example by means of a clutch and the guard shallcarry a warning sign stating the following:„All displacement of the machine outside the cutting area shall be carried out with the tool not inrotation“ (see figure D.2).5.1.3Minimum strength of the guardThe guards for rotating tools shall be so designed to resist strains resulting from an accidentalprojection of a segment of the cutting-off wheel. Any brittleness damage of the guard materialshall be avoided. A permanent plastic deformation of the guard resulting from stresses isacceptable as long as the guard fulfils its protective function and can be normallyassembled/disassembled.The guards shall remain attached to the frame in the case of projection of segments of thecutting-off wheel.Annex C indicates characteristics of guards which correctly fulfil their function.5.1.4 Immobilization, stability5.1.4.1 ImmobilizationMachines whose nominal mass exceeds 100 kg shall be equipped with a device which allowstheir immobilization (e. g. mechanical parking brake or self-sustaining system) on a slope of 10°with the machine in a position and configuration giving the maximum load on the brakedwheel(s).5.1.4.2 StabilityThe machines shall be designed and constructed so that they are sufficiently stable under theintended operating conditions, e.g. movement on site, cutting and parking.This shall be verified under the most unfavorable conditions specified by the manufacturer withthe machine located on a plane inclined at 10° to the horizontal and with the machine powersource switched off. The immobilization means (if any) shall be in use during the test. Formachines without immobilization means the wheels shall be blocked for the test. Under thesetest conditions the machine shall not overturn.SIST EN 13862:2002
EN 13862:2001 (E)135.1.5Transport and handlingThe movable parts of the machine shall be either lockable or removable to avoid any risk ofshearing or crushing e.g. during handling and carrying.NOTE For technical requirements relating to transport and lifting of the machine see 1.1.5 ofEN 292-2:1991, annex A.5.1.6Fixing of the tool(s)5.1.6.1Device for mounting the rotating tool(s)The device for mounting the rotating tool(s) shall be so designed that loosening and untighten-ing shall be possible only by an intentional manual action (e.g. retaining the rotating tool(s) onthe drive spindle by a threaded nut, the thread direction of which prevents unscrewing of the nutduring the cutting operation).5.1.6.2Flanges5.1.6.2.1Mounting of a cutting-off wheelThe flanges intended to mount a rotating tool shall comply with the requirements of annex B.5.1.6.2.2Mounting of several cutting-off wheels for grooving and milling operationsWhere the machine is designed for grooving and milling operations with several cutting-offwheels mounted on the same spindle, the manufacturer shall specify that
the spacer discswhich allows the width of the saw cut to be altered to make the required groove width shall havethe following performance requirements:-when rotating, the spacer disc(s) shall be prevented from moving in relation to thecutting tools and spindle by a positive device and not only by the tightening of theflanges;-the use of multiple mounted cutting tools shall be effected without additional modifica-tion to existing guards or exchange of guards;-secure and safe fixing of the multiple tools on the spindle shall be provided.The manufacturer shall indicate the limitations and intended modifications of this application
inthe operator’s instructions.5.1.7Starting with a crankInternal combustion engines which are hand-started using a crank shall be designed to avoidhazards caused by kick-back, for example, a safety crank shall be provided or the engine shallbe fitted with an internal anti-kick-back device.Easily accessible storage facilities shall be provided for safety starting cranks.SIST EN 13862:2002
EN 13862:2001 (E)145.1.8Controls5.1.8.1GeneralFor control functions in electric systems see clauses 7, 9, 11 and 13 of EN 60204-1:1997 andfor safety related parts, see EN 954-1:1996.5.1.8.2 Stop control(s)The following stop control devices shall be provided at the intended operator´s position:- a control for stopping the whole machine;-a control enabling the rotation of the tool to be stopped (see 5.1.2.3.3)5.1.8.3Control for feed movementSelf-propelled machines (see 3.2.3) shall be equipped with a control at the operator’s positionwhich allows disengagement of the feed system.Self-propelled machines with the exception of those with a manually started engine shall beequipped with a device that shall prevent starting the engine when the feed mode is selected(neutral start function).Self-propelled pedestrian controlled machines whose travelling speed towards to the operator isgreater than 25 m/min (1,5 km/h) shall be equipped with a “hold to run” control.5.1.9Failure of the power supplyAn interruption of the power supply and re-establishment after an interruption shall not lead to adangerous situation in particular:-the machine shall not be restarted automatically, an intentional action shall be neces-sary;-the machine shall not be prevented from stopping if the stop command has been given.5.2Electrical hazards5.2.1GeneralMachines with an electrical motor power
< 4 kW shall fulfil the electrical safety requirements ofEN 61029-1:1995.Other machines with an electrical motor shall fulfil the electrical safety requirements ofEN 60204-1:1997, in particular clauses 4, 5, 6, 14, 15 and 16. In addition to 4.4.2 ofEN 60204-1:1997 these machines shall work as intended in an ambient temperature range of0° C to 40° C.The enclosure of the electric controls shall provide a degree of protection of at least IP 54 asdefined in EN 60529:1991.SIST EN 13862:2002
EN 13862:2001 (E)155.2.2Water pumpWhere water is supplied by an electrical pump for flushing the tool(s) the pump shall fulfil therelevant requirements of EN 60335-1:1994 and EN 60335-2-41:1996.5.3Thermal hazards5.3.1Handles and other surfaces which require continuous contact shall have a surfacetemperatu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.