SIST EN ISO 12625-12:2010
(Main)Tissue paper and tissue products - Part 12: Determination of tensile strength of perforated lines - Calculation of perforation efficiency (ISO 12625-12:2010)
Tissue paper and tissue products - Part 12: Determination of tensile strength of perforated lines - Calculation of perforation efficiency (ISO 12625-12:2010)
This part of ISO 12625 specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation. This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper. The calculation of perforation efficiency is also specified in this part of ISO 12625. It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products can be carried out according to ISO 15755. For the determination of moisture content in tissue paper and tissue products, ISO 287 can be applied.
Tissue-Papier und Tissue-Produkte - Teil 12: Bestimmung der breitenbezogenen Bruchkraft an Perforationen - Berechnung der Perforations-Effizienz (ISO 12625-12:2010)
Dieser Teil der ISO 12625 legt ein Prüfverfahren für die Bestimmung der breitenbezogenen Bruchkraft an
Perforationen von Tissue-Papier fest. Hierfür wird ein Zugprüfgerät benutzt, das mit einer konstanten
Dehngeschwindigkeit arbeitet.
Die Berechnung der Perforations-Effizienz wird ebenfalls in diesem Dokument festgelegt.
Darüber hinaus wird ausdrücklich darauf hingewiesen, dass zur Erkennung von Unreinheiten und
Verunreinigungen in Tissue-Papier und Tissue-Produkten ISO 15755 angewendet werden sollte.
Für die Bestimmung des Feuchtegehaltes in Tissue-Papier und Tissue-Produkten sollte ISO 287 angewendet
werden.
Papier tissue et produits tissues - Partie 12: Détermination de la résistance à la rupture par traction de perforations - Calcul de l'efficacité des perforations (ISO 12625-12:2010)
L'ISO 12625-12:2010 spécifie une méthode d'essai permettant de déterminer la résistance à la rupture par traction des lignes de prédécoupe du papier tissue. Elle utilise un appareil d'essai de traction fonctionnant à une vitesse d'allongement constante.
Cette méthode doit être utilisée uniquement pour mesurer la résistance à la traction dans le sens machine, donc pour des lignes de prédécoupe dans le sens travers du papier tissue.
Le calcul de l'efficacité des perforations est également indiqué dans l'ISO 12625-12:2010.
Tissue papir in proizvodi iz tissue papirja - 12. del: Ugotavljanje natezne trdnosti perforacije - Izračun učinka perforacije (ISO 12625-12:2010)
Ta del ISO 12625 določa preskusno metodo za ugotavljanje natezne trdnosti perforacije tissue papirja. Uporablja napravo za preskušanje natezne trdnosti, ki deluje s stalno stopnjo raztezka. Ta metoda se uporablja samo za merjenje natezne trdnosti v smeri gibanja v stroju, to je za perforacije v prečni smeri na tissue papirju. Izračun učinkovitosti perforacij je prav tako določen v tem delu ISO 12625. Izrecno je navedeno, da se odkrivanje nečistoč in nasprotovanj v tissue papirju in tissue izdelkih lahko izvaja v skladu z ISO 15755. Za določanje vsebnosti vlage v tissue papirju in tissue izdelkih se lahko uporabi ISO 287.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 12625-12:2010
01-marec-2010
7LVVXHSDSLULQSURL]YRGLL]WLVVXHSDSLUMDGHO 8JRWDYOMDQMHQDWH]QHWUGQRVWL
SHUIRUDFLMH,]UDþXQXþLQNDSHUIRUDFLMH ,62
Tissue paper and tissue products - Part 12: Determination of tensile strength of
perforated lines - Calculation of perforation efficiency (ISO 12625-12:2010)
Tissue-Papier und Tissue-Produkte - Teil 12: Bestimmung der breitenbezogenen
Bruchkraft an Perforationen - Berechnung der Perforations-Effizienz (ISO 12625-
12:2010)
Papier tissue et produits tissues - Partie 12: Détermination de la résistance à la rupture
par traction de perforations - Calcul de l'efficacité des perforations (ISO 12625-12:2010)
Ta slovenski standard je istoveten z: EN ISO 12625-12:2010
ICS:
85.080.20 Tissue papir Tissue paper
SIST EN ISO 12625-12:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 12625-12:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 12625-12:2010
EUROPEAN STANDARD
EN ISO 12625-12
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2010
ICS 85.080.20
English Version
Tissue paper and tissue products - Part 12: Determination of
tensile strength of perforated lines - Calculation of perforation
efficiency (ISO 12625-12:2010)
Papier tissue et produits tissues - Partie 12: Détermination Tissue-Papier und Tissue-Produkte - Teil 12: Bestimmung
de la résistance à la rupture par traction des lignes de der breitenbezogenen Bruchkraft an Perforationen -
prédécoupe - Calcul de l'efficacité des perforations (ISO Berechnung der Perforations-Effizienz (ISO 12625-
12625-12:2010) 12:2010)
This European Standard was approved by CEN on 9 January 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12625-12:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 12625-12:2010
EN ISO 12625-12:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 12625-12:2010
EN ISO 12625-12:2010 (E)
Foreword
This document (EN ISO 12625-12:2010) has been prepared by Technical Committee CEN/TC 172 “Pulp,
paper and board”, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 6
“Paper, board and pulps”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by July 2010, and conflicting national standards shall be withdrawn at the
latest by July 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 12625-12:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 12625-12:2010
INTERNATIONAL ISO
STANDARD 12625-12
First edition
2010-01-15
Tissue paper and tissue products —
Part 12:
Determination of tensile strength
of perforated lines — Calculation
of perforation efficiency
Papier tissue et produits tissues —
Partie 12: Détermination de la résistance à la rupture par traction
des lignes de prédécoupe — Calcul de l'efficacité des perforations
Reference number
ISO 12625-12:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 12625-12:2010
ISO 12625-12:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 12625-12:2010
ISO 12625-12:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Principle.2
5 Apparatus.2
5.1 Tensile-testing apparatus.2
5.2 Tensile-tester clamps.2
5.3 Cutting device.3
6 Sampling.3
7 Conditioning .3
8 Preparation of test pieces.3
8.1 Dimensions .3
8.2 Number of test pieces.4
9 Procedure.4
9.1 General .4
9.2 Non-perforated test pieces.4
9.3 Perforated test pieces.4
10 Calculation .6
10.1 Tensile strength.6
10.2 Calculation of perforation efficiency .6
11 Test report.6
12 Precision.7
12.1 General .7
12.2 Tensile strength of non-perforated and perforated products.8
12.3 Perforation efficiency.9
Annex A (informative) Influence of a pre-cut in the perforation line .10
Annex B (informative) Influence of paper ageing .12
Bibliography.14
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 12625-12:2010
ISO 12625-12:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12625-12 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 172, Pulp, paper and board, in collaboration with Technical Committee ISO/TC 6, Paper, board and
pulps, Subcommittee SC 2, Test methods and quality specifications for paper and board, in accordance with
the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
ISO 12625 consists of the following parts, under the general title Tissue paper and tissue products:
⎯ Part 1: General principles for the use of terms
⎯ Part 3: Determination of thickness, bulking thickness and apparent bulk density
⎯ Part 4: Determination of tensile strength, stretch at break and tensile energy absorption
⎯ Part 5: Determination of wet tensile strength
⎯ Part 6: Determination of grammage
⎯ Part 7: Determination of optical properties
⎯ Part 8: Water-absorption time and water-absorption capacity, basket-immersion test method
⎯ Part 9: Determination of ball burst strength
⎯ Part 12: Determination of tensile strength of perforated lines — Calculation of perforation efficiency
The following part is under preparation:
⎯ Part 13: Determination of the spectral reflectance factor (brightness) at the wavelength R 457 nm with
and without UV stimulus and opacity
iv © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 12625-12:2010
ISO 12625-12:2010(E)
Introduction
Tissue papers such as toilet paper and kitchen towel are often pre-cut. They are used after separation of two
consecutive sheets.
It is important to know the efficiency of the pre-cut perforations.
The perforation strength should be enough to ensure the product cohesion, but not too high, so that sheets
can be easily separated. Depending on the type of tissue product, forces can be applied perpendicular to the
perforation lines, or in the direction of the perforation lines.
This part of ISO 12625 has been prepared by harmonizing those standards applicable to tissue paper and
tissue products that are currently in use. It specifies a procedure to determine perforation efficiency based on
the method described in ISO 12625-4 for the determination of the tensile strength of tissue paper and tissue
products.
© ISO 2010 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 12625-12:2010
---------------------- Page: 12 ----------------------
SIST EN ISO 12625-12:2010
INTERNATIONAL STANDARD ISO 12625-12:2010(E)
Tissue paper and tissue products —
Part 12:
Determination of tensile strength of perforated lines —
Calculation of perforation efficiency
1 Scope
This part of ISO 12625 specifies a test method for the determination of the tensile strength of perforated lines
of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction
perforations on tissue paper.
The calculation of perforation efficiency is also specified in this part of ISO 12625.
It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products can be
carried out according to ISO 15755.
For the determination of moisture content in tissue paper and tissue products, ISO 287 can be applied.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 186, Paper and board — Sampling to determine average quality
ISO 187, Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for
monitoring the atmosphere and conditioning of samples
ISO 536, Paper and board — Determination of grammage
ISO 1924-2, Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation
method (20 mm/min)
ISO 7500-1, Metallic materials — Verification of static uniaxial test
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.