SIST EN 13445-5:2002/A5:2007
(Amendment)Unfired pressure vessels - Part 5: Inspection and testing
Unfired pressure vessels - Part 5: Inspection and testing
Amendment to Non-destructive testing requirements
Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
Récipients sous pression non soumis a la flamme - Partie 5: Inspection et contrôles
Neogrevane tlačne posode – 5. del: Kontrola in preskušanje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13445-5:2002/A5:2007
01-januar-2007
1HRJUHYDQHWODþQHSRVRGH±GHO .RQWURODLQSUHVNXãDQMH
Unfired pressure vessels - Part 5: Inspection and testing
Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
Récipients sous pression non soumis a la flamme - Partie 5: Inspection et contrôles
Ta slovenski standard je istoveten z: EN 13445-5:2002/A5:2006
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST EN 13445-5:2002/A5:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 13445-5:2002/A5
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2006
ICS 23.020.30
English Version
Unfired pressure vessels - Part 5: Inspection and testing
Récipients sous pression non soumis à la flamme - Partie Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
5: Inspection et contrôles
This amendment A5 modifies the European Standard EN 13445-5:2002; it was approved by CEN on 27 April 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-5:2002/A5:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 13445-5:2002/A5:2006 (E)
Foreword
This document (EN 13445-5:2002/A5:2006) has been prepared by Technical Committee CEN/TC 54 “Unfired
pressure vessels”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13445-5:2002 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by February 2007, and conflicting
national standards shall be withdrawn at the latest by February 2007.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
This document includes the text of the amendment itself. The corrected pages of EN 13445-5 will be delivered
as issue xx of the standard.
2
---------------------- Page: 3 ----------------------
EN 13445-5:2002/A5:2006 (E)
2 Normative references
Replace:
prEN ISO 5817:2002, Welding – Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) – Quality levels for imperfections (ISO/DIS 5817:2002).
By:
EN ISO 5817:2003, Welding – Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) – Quality levels for imperfections (ISO 5817:2003).
3
---------------------- Page: 4 ----------------------
EN 13445-5:2002/A5:2006 (E)
6.6.3.2 Applicable non-destructive testing techniques
Replace by:
Table 6.6.3-1 shows the method, characterisation and acceptance criteria. This table is based on
EN 12062:1997 and also on Quality level C of EN ISO 5817:2003.
Table 6.6.3-1 — NDT methods, techniques, characterisation, acceptance criteria
NDT Methods (abbreviations) Techniques Characterisation Acceptance Criteria
Visual inspection (VT) EN 970:1997 EN ISO 5817:2003 EN ISO 5817:2003
(surface imperfections) (surface imperfections
c
Acceptance level C)
Radiography (RT) EN 1435:1997 class B EN 12517:1998 and EN 12517:1998,
additional table 6.6.4-1 Acceptance level 2, and
Table 6.6.4-1
b
Ultrasonic Testing(UT) EN 1714:1997
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.