oSIST prEN ISO/ASTM 52910:2022

Additive manufacturing - Design - Requirements, guidelines and recommendations (ISO/ASTM DIS 52910:2022)

Additive Fertigung - Konstruktion - Anforderungen, Richtlinien und Empfehlungen (ISO/ASTM DIS 52910:2022)

Fabrication additive - Conception - Exigences, lignes directrices et recommandations (ISO/ASTM DIS 52910:2022)

Aditivna proizvodnja - Konstruiranje - Zahteve, smernice in priporočila (ISO/ASTM DIS 52910:2022)

General Information

• Status: Not Published
• Public Enquiry End Date: 01-Oct-2022
• ICS: 25.030 - Additive manufacturing
• Technical Committee: VAR - Welding
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 23-Sep-2024
• Due Date: 28-Sep-2024
• Completion Date: 23-Sep-2024
• Ref Project: prEN ISO/ASTM 52910 - Additive manufacturing - Design - Requirements, guidelines and recommendations (ISO/ASTM DIS 52910:2022)

Relations

• Revised: SIST EN ISO/ASTM 52910:2019 - Additive manufacturing - Design - Requirements, guidelines and recommendations (ISO/ASTM 52910:2018)
• Effective Date: 01-Sep-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2022
Aditivna proizvodnja - Načrtovanje - Zahteve, smernice in priporočila (ISO/ASTM
DIS 52910:2022)
Additive manufacturing - Design - Requirements, guidelines and recommendations
Additive Fertigung - Konstruktion - Anforderungen, Richtlinien und Empfehlungen
Fabrication additive - Conception - Exigences, lignes directrices et recommandations
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52910
ICS:
25.030 3D-tiskanje Additive manufacturing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52910
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-08-17 2022-11-09
Additive manufacturing — Design — Requirements,
guidelines and recommendations
Fabrication additive — Conception — Exigences, lignes directrices et recommandations
ICS: 25.030
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/ASTM DIS 52910:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2022

ISO/ASTM DIS 52910:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52910
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:

Additive manufacturing — Design — Requirements,
guidelines and recommendations
Fabrication additive — Conception — Exigences, lignes directrices et recommandations
ICS: 25.030
This document is circulated as received from the committee secretariat.
© ISO/ASTM International 2022 THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
NOT BE REFERRED TO AS AN INTERNATIONAL
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below STANDARD UNTIL PUBLISHED AS SUCH.
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
ISO copyright office ASTM International
TECHNOLOGICAL, COMMERCIAL AND
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
USER PURPOSES, DRAFT INTERNATIONAL
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
Phone: [phone] Phone: [phone]
POTENTIAL TO BECOME STANDARDS TO
Fax: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail] Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org Website: www.astm.org ISO/ASTM DIS 52910:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO/ASTM International 2022 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2022

ISO/ASTM DIS 52910:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Purpose . 1
5 Design opportunities and limitations . 5
5.1 General . 5
5.2 Design opportunities . 6
5.3 Design limitations . . 7
6 Design considerations . 8
6.1 General . 8
6.2 Product considerations . 8
6.3 Product usage considerations . 9
6.3.1 General . 9
6.3.2 Thermal environment . . 9
6.3.3 Chemical exposure . 9
6.3.4 Radiation exposure . 9
6.3.5 Other exposure . 10
6.4 Sustainability considerations . . 10
6.5 Business considerations . 11
6.6 Geometry considerations .13
6.7 Material property considerations . 15
6.7.1 General .15
6.7.2 Mechanical properties . .15
6.7.3 Thermal properties . 16
6.7.4 Electrical properties . 16
6.7.5 Other . 16
6.8 Process considerations . 17
6.8.1 General . 17
6.8.2 Specific process considerations . 17
6.8.3 Other considerations . 19
6.9 Communication considerations . 19
7 Warnings to designers .20
Bibliography .22
iii
© ISO/ASTM International 2022 – All rights reserved

ISO/ASTM DIS 52910:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by ISO/TC 261, Additive manufacturing, in cooperation with ASTM F42,
Additive Manufacturing Technologies, on the basis of a partnership agreement between ISO and ASTM
International with the aim to create a common set of ISO/ASTM standards on additive manufacturing.
iv
© ISO/ASTM International 2022 – All rights reserved

DRAFT INTERNATIONAL STANDARD ISO/ASTM DIS 52910:2022(E)
Additive manufacturing — Design — Requirements,
guidelines and recommendations
1 Scope
This document gives requirements, guidelines and recommendations for using additive manufacturing
(AM) in product design.
It is applicable during the design of all types of products, devices, systems, components or parts that
are fabricated by any type of AM system. This document helps determine which design considerations
can be utilized in a design project or to take advantage of the capabilities of an AM process.
General guidance and identification of issues are supported, but specific design solutions and process-
specific or material-specific data are not supported.
The intended audience comprises three types of users:
— designers who are designing products to be fabricated in an AM system and their managers;
— students who are learning mechanical design and computer-aided design;
— developers of AM design guidelines and design guidance systems.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/ASTM 52900 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Purpose
4.1 This document provid
...