SIST EN 60317-0-2:2014
(Main)Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire
Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire
EN-IEC 60317-0-2 specifies the general requirements of enamelled rectangular copper winding wires. The range of nominal conductor dimensions is given in the relevant specification sheet.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-2: Allgemeine Anforderungen - Flachdrähte aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Partie 0-2: Prescriptions générales - Fil de section rectangulaire en cuivre émaillé
La CEI 60317-0-2:2013 spécifie les exigences générales pour les fils de bobinage de section rectangulaire en cuivre émaillé. La gamme des dimensions nominales des conducteurs est donnée dans la feuille de spécification appropriée. Cette troisième édition de la CEI 60317-0-2 annule et remplace la deuxième édition parue en 1997, l'Amendement 1:1999 et l'Amendement 2:2005. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - ajout du Paragraphe 3.2.2 transférant des exigences générales sur le fil de bobinage, présentes dans le domaine d'application; - correction des unités du Tableau 7; - modification des exigences de l'Article 15 avec une simple référence à la CEI 60172; - suppression de l'Annexe E. Mots clés: exigences pour les fils de bobinage de section rectangulaire en cuivre émaillé
Specifikacije za posebne vrste navijalnih žic - 0-2. del: Splošne zahteve - Emajliran bakren vodnik s pravokotnim prerezom (IEC 60317-0-2:2013)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60317-0-2:2014
01-marec-2014
1DGRPHãþD
SIST EN 60317-0-2:2001
SIST EN 60317-0-2:2001/A1:2001
SIST EN 60317-0-2:2001/A2:2005
Specifikacije za posebne vrste navijalnih žic - 0-2. del: Splošne zahteve - Emajliran
bakren vodnik s pravokotnim prerezom (IEC 60317-0-2:2013)
Specifications for particular types of winding wires - Part 0-2: General requirements -
Enamelled rectangular copper wire
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-2:
Allgemeine Anforderungen - Flachdrähte aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Partie 0-2: Prescriptions
générales - Fil de section rectangulaire en cuivre émaillé
Ta slovenski standard je istoveten z: EN 60317-0-2:2014
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
SIST EN 60317-0-2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60317-0-2:2014
---------------------- Page: 2 ----------------------
SIST EN 60317-0-2:2014
EUROPEAN STANDARD
EN 60317-0-2
NORME EUROPÉENNE
January 2014
EUROPÄISCHE NORM
ICS 29.060.10 Supersedes EN 60317-0-2:1998 + A1:2000 + A2:2005
English version
Specifications for particular types of winding wires -
Part 0-2: General requirements -
Enamelled rectangular copper wire
(IEC 60317-0-2:2013)
Spécifications pour types particuliers de Technische Lieferbedingungen für
fils de bobinage - bestimmte Typen von Wickeldrähten -
Partie 0-2: Exigences générales - Teil 0-2: Allgemeine Anforderungen -
Fil de section rectangulaire en cuivre Lackisolierte Flachdrähte aus Kupfer
émaillé (IEC 60317-0-2:2013)
(CEI 60317-0-2:2013)
This European Standard was approved by CENELEC on 2013-11-11. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-2:2014 E
---------------------- Page: 3 ----------------------
SIST EN 60317-0-2:2014
EN 60317-0-2:2014 - 2 -
Foreword
The text of document 55/1410/FDIS, future edition 3 of IEC 60317-0-2, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60317-0-2:2014.
The following dates are fixed:
(dop) 2014-08-11
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2016-11-11
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60317-0-2:1998.
EN 60317-0-2:2014 includes the following significant technical changes with respect to
EN 60317-0-2:1998:
– addition of 3.2.2, transferring general winding wire requirements from the scope;
– correction to Table 7 units;
– change to Clause 15 requirements with a simple reference to EN 60172;
– deletion of Annex E.
This standard is to be read in conjunction with the EN 60851 series. The clause numbers used in this
part of EN 60317 are identical with the respective test numbers of EN 60851 series.
In case of inconsistencies between EN 60851 and this part of EN 60317, the latter prevails.
The numbering of clauses in this standard is not continuous from Clauses 21 and 30 in order to
reserve space for possible future wire requirements prior to those for wire packaging.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60317-0-2:2013 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified).
IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified).
---------------------- Page: 4 ----------------------
SIST EN 60317-0-2:2014
- 3 - EN 60317-0-2:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the EN 60172 -
temperature index of enamelled winding
wires
IEC 60851 Series Winding wires - Test methods EN 60851 Series
ISO 3 - Preferred numbers - Series of preferred - -
numbers
---------------------- Page: 5 ----------------------
SIST EN 60317-0-2:2014
---------------------- Page: 6 ----------------------
SIST EN 60317-0-2:2014
IEC 60317-0-2
®
Edition 3.0 2013-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 0-2: General requirements – Enamelled rectangular copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-2: Exigences générales – Fil de section rectangulaire en cuivre émaillé
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX T
ICS 29.060.10 ISBN 978-2-8322-1149-6
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60317-0-2:2014
– 2 – 60317-0-2 © IEC:2013
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions . 9
4.1 Conductor dimensions . 9
4.2 Tolerance on conductor dimensions . 9
4.3 Rounding of corners . 10
4.4 Increase in dimensions due to the insulation . 12
4.5 Overall dimensions . 12
4.5.1 Nominal overall dimensions. 12
4.5.2 Minimum overall dimensions . 12
4.5.3 Maximum overall dimensions . 12
5 Electrical resistance . 13
6 Elongation . 13
7 Springiness . 13
8 Flexibility and adherence . 13
8.1 Mandrel winding test . 13
8.2 Adherence test . 13
9 Heat shock . 14
10 Cut-through . 14
11 Resistance to abrasion . 14
12 Resistance to solvents . 14
13 Breakdown voltage . 14
14 Continuity of insulation . 14
15 Temperature index . 14
16 Resistance to refrigerants . 15
17 Solderability . 15
18 Heat or solvent bonding . 15
19 Dielectric dissipation factor . 15
20 Resistance to transformer oil . 15
21 Loss of mass . 15
23 Pin hole test . 15
30 Packaging. 15
Annex A (informative) Nominal cross-sectional areas for preferred and intermediate
sizes . 17
Bibliography . 25
---------------------- Page: 8 ----------------------
SIST EN 60317-0-2:2014
60317-0-2 © IEC:2013 – 3 –
Table 1 – Conductor tolerances . 10
Table 2 – Nominal cross-sectional areas of preferred sizes. 11
Table 3 – Corner radii . 12
Table 4 – Increases in dimensions. 12
Table 5 – Elongation . 13
Table 6 – Mandrel winding . 13
Table 7 – Breakdown voltage . 14
Table A.1 – Nominal cross-sectional areas (1 of 7) . 17
Table B.1 – Tolerances for calculating special maximum and minimum dimensions of
grade 2 rectangular wire . 24
---------------------- Page: 9 ----------------------
SIST EN 60317-0-2:2014
– 4 – 60317-0-2 © IEC:2013
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR
TYPES OF WINDING WIRES –
Part 0-2: General requirements –
Enamelled rectangular copper wire
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60317-0-2 has been prepared by IEC technical committee 55:
Winding wires.
This third edition cancels and replaces the second edition published in 1997,
Amendment 1:1999 and Amendment 2:2005. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
– addition of 3.2.2, transferring general winding wire requirements from the scope;
– correction to Table 7 units;
– change to Clause 15 requirements with a simple reference to IEC 60172;
– deletion of Annex E.
---------------------- Page: 10 ----------------------
SIST EN 60317-0-2:2014
60317-0-2 © IEC:2013 – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
55/1410/FDIS 55/1431/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This International standard is to be read in conjunction with the IEC 60851 series. The clause
numbers used in this part of IEC 60317 are identical with the respective test numbers of
IEC 60851 series.
In case of inconsistencies between IEC 60851 and this part of IEC 60317, the latter prevails.
The numbering of clauses in this standard is not continuous from Clauses 21 and 30 in order to
reserve space for possible future wire requirements prior to those for wire packaging.
A list of all parts in the IEC 60317 series, published under the general title Specifications for
particular types of winding wires, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN 60317-0-2:2014
– 6 – 60317-0-2 © IEC:2013
INTRODUCTION
This part of IEC 60317 is one of a series which deals with insulated wires used for windings in
electrical equipment. The series has three groups describing:
1) Winding wires – Test methods (IEC 60851);
2) Specifications for particular types of winding wires (IEC 60317);
3) Packaging of winding wires (IEC 60264).
---------------------- Page: 12 ----------------------
SIST EN 60317-0-2:2014
60317-0-2 © IEC:2013 – 7 –
SPECIFICATIONS FOR PARTICULAR
TYPES OF WINDING WIRES –
Part 0-2: General requirements –
Enamelled rectangular copper wire
1 Scope
This part of IEC 60317 specifies the general requirements of enamelled rectangular copper
winding wires.
The range of nominal conductor dimensions is given in the relevant specification sheet.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
IEC 60172, Test procedure for the determination of the temperature index of enamelled winding
wires
IEC 60851 (all parts), Winding wires – Test methods
ISO 3, Preferred numbers – Series of preferred numbers
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
class
thermal performance of a wire expressed by the temperature index and the heat shock
temperature
3.1.2
coating
material which is deposited on a conductor or wire by a suitable means and then dried and/or
cured
3.1.3
conductor
bare metal after removal of the insulation
3.1.4
crack
opening in the insulation which exposes the conductor to view at the stated magnification
---------------------- Page: 13 ----------------------
SIST EN 60317-0-2:2014
– 8 – 60317-0-2 © IEC:2013
3.1.5
dual coating
insulation composed of two different materials, an underlying and a superimposed coating
3.1.6
enamelled wire
wire coated with an insulation of cured resin
3.1.7
grade
range of thickness of the insulation of a wire
3.1.8
insulation
coating or covering on the conductor with the specific function of withstanding voltage
3.1.9
nominal conductor dimension
designation of the conductor size in accordance with the IEC 60317 series
3.1.10
normal vision
20/20 vision, with corrective lenses, if necessary
3.1.11
winding wire
wire used for winding a coil to provide a magnetic field
3.1.12
wire
conductor coated or covered with an insulation
3.2 General notes
3.2.1 Methods of test
All methods of test to be used for this standard are given in IEC 60851.
The clause numbers used in this standard are identical to the corresponding test numbers in
the IEC 60851 series of standards.
In case of inconsistencies between the publication on methods of test and this standard,
IEC 60317-0-2 shall prevail.
Where no specific range of nominal conductor dimensions is given for a test, the test applies to
all nominal conductor dimensions covered by the specification sheet.
Unless otherwise specified, all tests shall be carried out at a temperature from 15 °C to 35 °C
and a relative humidity from 45 % to 75 %. Before measurements are made, the specimens
shall be preconditioned under these atmospheric conditions for a time sufficient to allow the
specimens to reach stability.
The wire to be tested shall be removed from the packaging in such a way that the wire will not
be subjected to tension or unnecessary bends. Before each test, sufficient wire should be
discarded to ensure that any damaged wire is not included in the test specimens.
---------------------- Page: 14 ----------------------
SIST EN 60317-0-2:2014
60317-0-2 © IEC:2013 – 9 –
3.2.2 Winding wire
When reference is made to a winding wire according to a standard of the IEC 60317 series
mentioned under Clause 2, the following information is given in the description:
– reference to IEC specification;
– nominal conductor dimensions in millimetres (width × thickness);
– grade.
EXAMPLE: IEC 60317-17 – 4,00 × 1,00 Grade 1
3.3 Appearance
The film coating shall be essentially smooth and continuous, free from streaks, blisters and
foreign material when examined with normal vision, as wound on the original spool or reel.
4 Dimensions
4.1 Conductor dimensions
The dimensions for widths and thickness of conductors of winding wires with rectangular cross-
section recommended in this standard are taken from the R 20 and R 40 series according to
ISO 3.
Preferred sizes are combinations of width and thickness both according to the R 20 series.
Intermediate sizes are combinations of width or thickness according to the R 20 series with the
other dimension according to the R 40 series.
This standard covers:
– widths from 2,00 mm up to and including 16,00 mm;
– thicknesses from 0,80 mm up to and including 5,60 mm.
For thicknesses over 5,60 mm up to and including 10 mm and for widths over 16 mm up to and
including 25 mm where, for technical reasons, additional sizes may be needed, the R 40 series
shall be used. The ratio width/thickness shall be within the specified limits and combinations of
R 40 and R 40 are not allowed in the case of additional sizes.
The ratio width/thickness shall be greater than or equal to 1,4:1 and shall not exceed 8:1.
*
The actual values of dimensions are given in Table 2 .
The nominal cross-sectional areas for preferred sizes are given in Table 2, and the nominal
cross-sectional areas for intermediate sizes are given in Table A.1.
4.2 Tolerance on conductor dimensions
The conductor dimensions shall not differ from the nominal values by more than the tolerance
given in Table 1.
________
*
Dimensions according to R 20 series are printed in larger type.
---------------------- Page: 15 ----------------------
SIST EN 60317-0-2:2014
– 10 – 60317-0-2 © IEC:2013
Table 1 – Conductor tolerances
Nominal width or thickness of the conductor
Tolerance
mm
±
mm
Over Up to and including
– 3,15 0,030
3,15 6,30 0,050
6,30 12,50 0,070
12,50 16,00 0,100
4.3 Rounding of corners
The arc shall merge smoothly into the flat surfaces of the conductor and the strip shall be free
from sharp, rough and projecting edges. The conductor shall have radiused corners complying
with Table 3. The specified radii shall be maintained within ±25 %.
---------------------- Page: 16 ----------------------
60317-0-2 © IEC:2013 – 11 –
SIST EN 60317-0-2:2014
Table 2 – Nominal cross-sectional areas of preferred sizes
---------------------- Page: 17 ----------------------
SIST EN 60317-0-2:2014
– 12 – 60317-0-2 © IEC:2013
Table 3 – Corner radii
Nominal thickness of conductor
Corner
mm
radius
Up to and including mm
Over
–
1,00 0,5 nominal thickness
0,50*
1,00 1,60
0,65**
1,60 2,24
0,80
2,24 3,55
1,00
3,55 5,60
NOTE If agreed between purchaser and supplier, the corner radii for wires with a
width greater than 4,8 mm may be:
* 0,5 nominal thickness
** 0,8 mm
4.4 Increase in dimensions due to the insulation
The increase in width or thickness due to the insulation shall be as given in Table 4.
Table 4 – Increases in dimensions
Increase in dimensions
mm
Grade
Minimum Nominal Maximum
1 0,06 0,085 0,11
2 0,12 0,145 0,17
4.5 Overall dimensions
4.5.1 Nominal overall dimensions
The nominal overall dimensions shall be calculated as the sum of the nominal bare conductor
and the nominal increase in dimension due to the insulation.
4.5.2 Minimum overall dimensions
The minimum overall dimensions shall be calculated as the sum of the minimum bare
conductor and the minimum increase in dimension due to the insulation. See also note under
4.5.3.
4.5.3 Maximum overall dimensions
The maximum overall dimensions shall be calculated as the sum of the maximum bare
conductor and the maximum increase in dimension due to the insulation.
NOTE When agreed between purchaser and supplier, special tolerances for grade 2 as given in Annex B can be
used to calculate special maximum and minimum dimensions.
---------------------- Page: 18 ----------------------
SIST EN 60317-0-2:2014
60317-0-2 © IEC:2013 – 13 –
5 Electrical resistance
The resistance of the wire shall be expressed as the d.c. resistance at 20 °C. The method used
shall provide an accuracy of 0,5 %.
The maximum value of resistance shall be not greater than the value calculated for the
minimum tolerated cross-sectional area of the conductor resulting from the minimum
dimensions in thickness and width and the maximum for the corner radius, and with a resistivity
2 –1
of 1/58 Ω·mm ·m .
One measurement shall be made.
6 Elongation
The elongation at fracture shall be in accordance with the values given in Table 5.
Table 5 – Elongation
Nominal thickness of the conductor
Minimum elongation
mm
%
Over Up to and including
– 2,50 30
2,50 5,60 32
7 Springiness
The wire shall not exceed the maximum springback of 5 degrees.
8 Flexibility and adherence
8.1 Mandrel winding test
The coating shall show no crack after the wire has been bent flatwise and edgewise on a
mandrel with a diameter as specified in Table 6.
Table 6 – Mandrel winding
Wire bent on Mandrel diameter
Width Sizes up to and including 10 mm
4 × width
Sizes over 10 mm
5 × width
Thickness All sizes 4 × thickness
8.2 Adherence test
The wire shall be stretched by 15 %. The distance of loss of adherence shall be less than
1 × width.
---------------------- Page: 19 ----------------------
SIST EN 60317-0-2:2014
– 14 – 60
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.