SIST EN ISO 5774:2009
(Main)Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2006)
Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2006)
This International Standard specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from 10 °C to + 60 °C. The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C, heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy service for use in mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C.
Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Spezifikation (ISO 5774:2006)
Diese Internationale Norm legt die Anforderungen für vier Typen von flexiblen Kunststoffschläuchen mit Textileinlage für Druckluftanwendungen in einem Temperaturbereich von − 10 °C bis + 60 °C fest.
Die vier Typen werden eingestuft in leichten Einsatzbereich mit einem maximalen Betriebsdruck von 7 bar bei 23 °C und 4,5 bar bei 60 °C, einen mittleren Einsatzbereich mit einem maximalen Betriebsdruck von 10 bar bei 23 °C und 6,5 bar bei 60 °C, einen schweren Einsatzbereich mit einem maximalen Betriebsdruck von
16 bar bei 23 °C und 11 bar bei 60 °C und einen schweren Einsatzbereich zur Anwendung im Bergbau mit einem maximalen Betriebsdruck von 25 bar bei 23 °C und 13 bar bei 60 °C.
Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé - Spécifications (ISO 5774:2006)
L'ISO 5774:2006 spécifie les exigences relatives à quatre types de tuyaux souples en thermoplastique armés de textile destinés aux applications d'air comprimé pour utilisation dans la plage des températures de -10 °C à +60 °C.
Les quatre types sont classés comme suit: service léger pour une pression maximale de service de 7 bar à 23 °C et de 4,5 bar à 60 °C, service moyen pour une pression maximale de service de 10 bar à 23 °C et de 6,5 bar à 60 °C, service intensif pour une pression maximale de service de 16 bar à 23 °C et de 11 bar à 60 °C, et service intensif dans les mines pour une pression maximale de service de 25 bar à 23 °C et de 13 bar à 60 °C.
Polimerne cevi - S tekstilom okrepljene cevi za zrak pod pritiskom - Specifikacija (ISO 5774:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 5774:2009
01-februar-2009
1DGRPHãþD
SIST EN ISO 5774:2000
Polimerne cevi - S tekstilom okrepljene cevi za zrak pod pritiskom - Specifikacija
(ISO 5774:2006)
Plastics hoses - Textile-reinforced types for compressed-air applications - Specification
(ISO 5774:2006)
Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Spezifikation
(ISO 5774:2006)
Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé -
Spécifications (ISO 5774:2006)
Ta slovenski standard je istoveten z: EN ISO 5774:2008
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 5774:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 5774:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 5774:2009
EUROPEAN STANDARD
EN ISO 5774
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2008
ICS 23.040.70 Supersedes EN ISO 5774:2000
English Version
Plastics hoses - Textile-reinforced types for compressed-air
applications - Specification (ISO 5774:2006)
Tuyaux en plastique - Types armés de textile pour Kunststoffschläuche - Textilverstärkte Typen für
applications avec de l'air comprimé - Spécifications (ISO Druckluftanwendungen - Spezifikation (ISO 5774:2006)
5774:2006)
This European Standard was approved by CEN on 26 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5774:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 5774:2009
EN ISO 5774:2008 (E)
Foreword
The text of ISO 5774:2006 has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 5774:2008 by Technical Committee CEN/TC 218 "Rubber and plastics hoses
and hose assemblies", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by July 2008, and conflicting national standards
shall be withdrawn at the latest by July 2008.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any
or all such patent rights.
This document supersedes EN ISO 5774:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of ISO 5774:2006 has been approved by CEN as EN ISO 5774:2008 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 5774:2009
INTERNATIONAL ISO
STANDARD 5774
Third edition
2006-07-01
Plastics hoses — Textile-reinforced types
for compressed-air applications —
Specification
Tuyaux en plastique — Types armés de textile pour applications avec
de l'air comprimé — Spécifications
Reference number
ISO 5774:2006(E)
©
ISO 2006
---------------------- Page: 5 ----------------------
SIST EN ISO 5774:2009
ISO 5774:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 5774:2009
ISO 5774:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Classification. 2
5 Couplings and end fittings . 2
6 Materials and construction . 2
7 Dimensions and tolerances . 2
7.1 Inside diameter, tolerances and minimum wall thickness . 2
7.2 Concentricity . 3
7.3 Tolerances on length. 3
8 Physical properties. 4
8.1 Plastic compounds. 4
8.1.1 Tensile strength and elongation at break of lining and cover . 4
8.1.2 Resistance to ageing. 4
8.1.3 Loss in mass on heating. 4
8.1.4 Resistance to liquids. 4
8.1.5 Hydrolysis test . 4
8.2 Performance requirements on finished hoses . 5
8.2.1 Hydrostatic requirements . 5
8.2.2 Adhesion. 5
8.2.3 Exposure to a xenon arc lamp. 5
8.2.4 Bending test . 6
8.2.5 Low-temperature flexibility . 6
9 Frequency of testing. 6
10 Marking . 7
11 Recommendations for packaging and storage . 7
12 Test report . 7
Annex A (normative) Hydrolysis test .8
Annex B (normative) Type approval and routine tests . 10
Annex C (informative) Production acceptance tests . 11
Annex D (informative) Couplings and end fittings. 12
Bibliography . 13
© ISO 2006 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 5774:2009
ISO 5774:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5774 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Hoses (rubber and plastics).
This third edition cancels and replaces the second edition (ISO 5774:1997), which has been technically
revised.
iv © ISO 2006 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 5774:2009
ISO 5774:2006(E)
Introduction
This International Standard has been prepared to provide minimum acceptable requirements for the
satisfactory performance of flexible thermoplastics hoses, textile reinforced, for compressed-air applications.
Maximum working pressures of each hose type are specified with two operating temperatures.
Some hose materials will require a hydrolysis test (given in Annex A).
© ISO 2006 – All rights reserved v
---------------------- Page: 9 ----------------------
SIST EN ISO 5774:2009
---------------------- Page: 10 ----------------------
SIST EN ISO 5774:2009
INTERNATIONAL STANDARD ISO 5774:2006(E)
Plastics hoses — Textile-reinforced types for compressed-air
applications — Specification
1 Scope
This International Standard specifies the requirements for four types of flexible thermoplastic hose, textile
reinforced, for compressed-air applications in the temperature range from − 10 °C to + 60 °C.
The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at
60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C, heavy
service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy service for use in
mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scales for assessing change in colour
ISO 176:2005, Plastics — Determination of loss of plasticizers — Activated carbon method
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and
tolerances on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1746, Rubber or plastics hoses and tubing — Bending tests
ISO 1817, Rubber, vulcanized — Determination of the effect of liquids
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of dimensions
ISO 4672:1997, Rubber and plastics hoses — Sub-ambient temperature flexibility tests
ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 8331, Rubber and plastics hoses and hose assemblies — Guide to selection, storage, use and
maintenance
ISO 11758:1995, Rubber and plastics hoses — Exposure to a xenon arc lamp — Determination of changes in
colour and appearance
© ISO 2006 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 5774:2009
ISO 5774:2006(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
4 Classification
Hoses are designated as one of the following four types depending on their pressure rating at the specified
temperature:
Type A: General industrial use — light service — for a maximum working pressure of 7 bar at 23 °C and
4,5 bar at 60 °C.
Type B: General industrial use — medium service — for a maximum working pressure of 10 bar at 23
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.