SIST EN ISO 1927-6:2013
(Main)Unshaped refractory materials - Part 6: Measurement of physical properties (ISO 1927-6:2012)
Unshaped refractory materials - Part 6: Measurement of physical properties (ISO 1927-6:2012)
This part of ISO 1927 specifies methods for the determination of properties of unshaped materials from test pieces prepared and stored according to ISO 1927-5. The methods are applicable to dense and insulating castables and to ramming materials (including plastics) as defined in ISO 1927-1 before and after firing.
Ungeformte feuerfeste Erzeugnisse - Teil 6: Bestimmung der physikalischen Eigenschaften (ISO 1927-6:2012)
Dieser Teil dieser Internationalen Norm legt Verfahren zur Bestimmung der Eigenschaften ungeformter Werkstoffe an Probekörpern, die nach ISO 1927-5 hergestellt und gelagert werden, fest. Die Verfahren gelten für dichte und wärmedämmende Feuerbetone und Rammmassen (einschließlich plastischer Massen), wie in ISO 1927-1 definiert, im ungebrannten und gebrannten Zustand.
Produits réfractaires non façonnés - Partie 6: Détermination des propriétés physiques (ISO 1927-6:2012)
L'ISO 1927-6:2012 spécifie des méthodes pour la détermination des propriétés de matériaux réfractaires monolithiques (non façonnés) à partir d'éprouvettes préparées et conservées conformément à l'ISO 1927-5.
Les méthodes sont applicables aux bétons denses et isolants et aux matériaux moulables (y compris les mélanges plastiques) tels que définis dans l'ISO 1927-1, avant et après cuisson.
Neoblikovani ognjevzdržni izdelki - 6. del: Merjenje fizikalnih lastnosti (ISO 1927-6:2012)
Ta del standarda ISO 1927 določa metode za ugotavljanje lastnosti neoblikovanih materialov iz vzorcev, pripravljenih in skladiščenih v skladu s standardom ISO 1927-5. Te metode se uporabljajo za zgoščene in izolacijske betone ter za mašilne materiale (vključno s plastiko), kot je opredeljeno v standardu ISO 1927-1, pred žganjem in po njem.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1927-6:2013
01-maj-2013
1DGRPHãþD
SIST EN 1402-6:2004
Neoblikovani ognjevzdržni izdelki - 6. del: Merjenje fizikalnih lastnosti (ISO 1927-
6:2012)
Unshaped refractory materials - Part 6: Measurement of physical properties (ISO 1927-
6:2012)
Ungeformte feuerfeste Erzeugnisse - Teil 6: Bestimmung der physikalischen
Eigenschaften (ISO 1927-6:2012)
Produits réfractaires non façonnés - Partie 6: Détermination des propriétés physiques
(ISO 1927-6:2012)
Ta slovenski standard je istoveten z: EN ISO 1927-6:2012
ICS:
81.080 Ognjevzdržni materiali Refractories
SIST EN ISO 1927-6:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 1927-6:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 1927-6:2013
EUROPEAN STANDARD
EN ISO 1927-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 81.080 Supersedes EN 1402-6:2003
English Version
Monolithic (unshaped) refractory products - Part 6:
Measurement of physical properties (ISO 1927-6:2012)
Produits réfractaires monolithiques (non façonnés) - Partie Ungeformte (monolithische) feuerfeste Erzeugnisse - Teil 6:
6: Détermination des propriétés physiques (ISO 1927- Bestimmung der physikalischen Eigenschaften (ISO 1927-
6:2012) 6:2012)
This European Standard was approved by CEN on 30 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1927-6:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 1927-6:2013
EN ISO 1927-6:2012 (E)
Contents Page
Foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 1927-6:2013
EN ISO 1927-6:2012 (E)
Foreword
This document (EN ISO 1927-6:2012) has been prepared by Technical Committee ISO/TC 33 "Refractories"
in collaboration with Technical Committee CEN/TC 187 “Refractory products and materials” the secretariat of
which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1402-6:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 1927-6:2012 has been approved by CEN as a EN ISO 1927-6:2012 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 1927-6:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 1927-6:2013
INTERNATIONAL ISO
STANDARD 1927-6
First edition
2012-12-01
Monolithic (unshaped) refractory
products —
Part 6:
Measurement of physical properties
Produits réfractaires monolithiques (non façonnés) —
Partie 6: Détermination des propriétés physiques
Reference number
ISO 1927-6:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 1927-6:2013
ISO 1927-6:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 1927-6:2013
ISO 1927-6:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Determination of geometric bulk density . 1
3.1 Principle . 1
3.2 Test pieces . 2
3.3 Apparatus . 2
3.4 Procedure . 2
3.5 Calculation and expression of test results . 3
4 Determination of density and porosity . 3
4.1 Principle . 3
4.2 Test pieces . 3
4.3 Procedure . 3
4.4 Calculation . 3
5 Determination of cold modulus of rupture . 3
5.1 Principle . 3
5.2 Test pieces . 4
5.3 Apparatus and procedure . 4
5.4 Test results . 4
6 Determination of cold crushing strength . 4
6.1 Principle . 4
6.2 Test pieces . 4
6.3 Apparatus . 5
6.4 Procedure . 5
6.5 Calculation and expression of results . 7
7 Determination of permanent linear change . 7
7.1 Principle . 7
7.2 Apparatus . 8
7.3 Procedure . 8
7.4 Calculation . 8
8 Determination of modulus of rupture at elevated temperatures . 9
8.1 Principle . 9
8.2 Apparatus and procedure . 9
8.3 Calculation and expression of results . 9
9 Determination of refractoriness under load and creep in compression . 9
9.1 Principle . 9
9.2 Test pieces . 9
9.3 Procedure . 9
9.4 Calculation and expression of test results .10
10 Test report .10
Bibliography . 11
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 1927-6:2013
ISO 1927-6:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1927-6 was prepared by Technical Committee ISO/TC 33, Refractories.
ISO 1927 consists of the following parts, under the general title Monolithic (unshaped) refractory products:
— Part 1: Introduction and classification
— Part 2: Sampling for testing
— Part 3: Characterization as received
— Part 4: Determination of consistency of castables
— Part 5: Preparation and treatment of test pieces
— Part 6: Measurement of physical properties
— Part 7: Tests on pre-formed shapes
— Part 8: Determination of complementary properties
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 1927-6:2013
INTERNATIONAL STANDARD ISO 1927-6:2012(E)
Monolithic (unshaped) refractory products —
Part 6:
Measurement of physical properties
1 Scope
This part of ISO 1927 specifies methods for the determination of properties of unshaped materials from test
pieces prepared and stored according to ISO 1927-5.
The methods are applicable to dense and insulating castables and to ramming materials (including plastics) as
defined in ISO 1927-1 before and after firing.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 1893, Refractory products — Determination of refractoriness under load — Differential method with
rising temperature
ISO 1927-5, Monolithic·(unshaped)·refractory·products — Part 5: Preparation and treatment of test pieces
ISO 3187 Refractory products — Determination of creep in compression
ISO 5013 Refractory products — Determination of modulus of rupture at elevated temperatures
ISO 5014: Dense and insulating shaped refractory products — Determination of modulus of rupture at
ambient temperature
ISO 5017, Dense shaped refractory products — Determination of bulk density, apparent porosity and true porosity
ISO 5018, Refractory materials — Determin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.