SIST EN ISO 14910-1:2013

Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specifications (ISO 14910-1:2013)

ISO 14910-1:2013 establishes a system of designation for thermoplastic polyester/ester and polyether/ester elastomers, which may be used as the basis for specifications.
The types of thermoplastic polyester/ester and polyether/ester elastomer are differentiated from each other by a classification system based on appropriate levels of the designatory properties
hardness;
melting temperature;
tensile/flexural modulus of elasticity;
and on information about the intended application and/or method of processing, important properties, additives, colour, fillers and reinforcing materials.
ISO 14910-1:2013 is applicable to all thermoplastic polyester/ester and polyether/ester elastomers. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colourants, fillers or other additives.

Kunststoffe - Thermoplastische Polyester/Ester- und Polyether/Ester-Elastomer-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 14910-1:2013)

In diesem Teil von ISO 14910 ist ein Bezeichnungssystem für thermoplastische Polyester/Ester- und
Polyether/Ester-Elastomer-Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann.
Die Polyester/Ester- und Polyether/Ester-Elastomer-Formmassen-Typen werden mit Hilfe eines Einteilungssystems
voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften
⎯ Härte;
⎯ Schmelztemperatur;
⎯ Zug-/Biege-Elastizitätsmodul
und Informationen über vorgesehene Anwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften,
Additive und Farbstoffe, Füll- und Verstärkungsstoffe beruht.
Dieser Teil von ISO 14910 ist für alle thermoplastischen Polyester/Ester- und Polyether/Ester-Elastomer-
Formmassen anwendbar. Er gilt für gebrauchsfertige Formmassen in Form von Pulver, Granulat oder Pellets
und für mit Farbstoffen, Füllstoffen oder sonstigen Additiven usw. modifizierte oder nicht modifizierte
Materialien.
Es darf nicht unterstellt werden, dass Formmassen mit der gleichen Bezeichnung notwendigerweise ein
gleiches Leistungsverhalten zeigen. Dieser Teil von ISO 14910 enthält keine technischen Daten,
Leistungsangaben oder Verarbeitungsbedingungen, die gefordert werden dürfen, um eine Formmasse für
eine bestimmte Anwendung und/oder Verarbeitungsart festzulegen. Falls derartige zusätzliche Eigenschaften
verlangt sind, müssen sie, falls zutreffend, mit Hilfe der in ISO 14910-2 festgelegten Prüfverfahren bestimmt
werden.
Um ein thermoplastisches Polyester/Ester- und Polyether/Ester-Elastomer-Material für eine bestimmte
Anwendung festzulegen oder um eine reproduzierbare Verarbeitung sicherzustellen, dürfen im Daten-Block 5
(3.1, 3.6) zusätzliche Anforderungen angegeben werden.

Plastiques - Élastomères thermoplastiques à base de polyester/ester et polyéther/ester, pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 14910-1:2013)

L'ISO 14910-1:2013 établit un système de désignation des élastomères thermoplastiques à base de polyester/ester et polyéther/ester qui peut être utilisé comme base pour les spécifications.
Les types de thermoplastiques à base de polyester/ester et polyéther/ester sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés des propriétés de désignation: a) la dureté; b) la température de fusion; c) le module d'élasticité en traction/en flexion; et sur des informations concernant l'application prévue et/ou la méthode de mise en oeuvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
L'ISO 14910-1:2013 est applicable à tous les élastomères thermoplastiques à base de polyester/ester et polyéther/ester. Elle s'applique aux matériaux prêts à l'emploi sous forme de poudres, grains ou granulés, non modifiés ou modifiés par des colorants, charges, ou autres additifs.

Polimerni materiali - Plastomerni poliester/ester in polieter/ester elastomeri za oblikovanje in ekstrudiranje - 1. del: Sistem označevanja in podlage za specifikacije (ISO 14910-1:2013)

Ta del standarda ISO 14910 določa sistem označevanja plastomernih poliester/ester in polieter/ester elastomerov, ki jih je mogoče uporabiti kot podlago za specifikacije. Vrste plastomernih poliester/ester in polieter/ester elastomerov se ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh označevalnih lastnosti: a) trdnosti, b) temperaturi taljenja, c) nateznih/upogibalnih modulih elastičnosti in na informacijah o načrtovani uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih ter materialih za ojačanje. Ta del standarda ISO 14910 se lahko uporablja za vse plastomerne poliester/ester in polieter/ester elastomere. Uporablja se za materiale v obliki praška, granul ali peletov, pripravljene za običajno uporabo, nespremenjene ali spremenjene z barvili, polnili ali drugimi aditivi. Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta del standarda ISO 14910 ne zagotavlja inženirskih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so morda potrebni za opredelitev materiala za določeno uporabo in/ali metodo obdelave. Če so take dodatne lastnosti zahtevane, se določijo v skladu s preskusnimi metodami iz standarda ISO 14910-2, če je to primerno. Da bi se določil plastomerni poliester/ester ali polieter/ester elastomer za določeno uporabo ali da bi se zagotovila obnovljiva obdelava, se lahko v podatkovnem bloku 5 navedejo dodatne zahteve.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 19-Jul-2010
• Publication Date: 05-May-2013
• Withdrawal Date: 18-Feb-2018
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 19-Feb-2018
• Due Date: 14-Mar-2018
• Completion Date: 19-Feb-2018
• Ref Project: EN ISO 14910-1:2013 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specification (ISO 14910-1:2013)

Relations

• Replaces: SIST EN ISO 14910-1:2006 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specifications (ISO 14910-1:1997)
• Effective Date: 01-Jun-2013
• Replaced By: SIST EN ISO 20029-1:2018 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specifications (ISO 20029-1:2017)
• Effective Date: 14-Feb-2018
• Revised: SIST EN ISO 14910-1:2006 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specifications (ISO 14910-1:1997)
• Effective Date: 01-Jun-2010

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2013
1DGRPHãþD
SIST EN ISO 14910-1:2006
3ROLPHUQLPDWHULDOL3ODVWRPHUQLSROLHVWHUHVWHULQSROLHWHUHVWHUHODVWRPHUL]D
REOLNRYDQMHLQHNVWUXGLUDQMHGHO6LVWHPR]QDþHYDQMDLQSRGODJH]D
VSHFLILNDFLMH,62
Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and
extrusion - Part 1: Designation system and basis for specifications (ISO 14910-1:2013)
Kunststoffe - Thermoplastische Polyester/Ester- und Polyether/Ester-Elastomer-
Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 14910-
1:2013)
Plastiques - Élastomères thermoplastiques à base de polyester/ester et polyéther/ester,
pour moulage et extrusion - Partie 1: Système de désignation et base de spécification
(ISO 14910-1:2013)
Ta slovenski standard je istoveten z: EN ISO 14910-1:2013
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 14910-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 83.080.20 Supersedes EN ISO 14910-1:2006
English Version
Plastics - Thermoplastic polyester/ester and polyether/ester
elastomers for moulding and extrusion - Part 1: Designation
system and basis for specification (ISO 14910-1:2013)
Plastiques - Élastomères thermoplastiques à base de Kunststoffe - Thermoplastische Polyester/Ester- und
polyester/ester et polyéther/ester, pour moulage et Polyether/Ester-Elastomer-Formmassen - Teil 1:
extrusion - Partie 1: Système de désignation et base de Bezeichnungssystem und Basis für Spezifikationen (ISO
spécification (ISO 14910-1:2013) 14910-1:2013)
This European Standard was approved by CEN on 1 December 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14910-1:2013: E
worldwide for CEN national Members.

Contents Page
Foreword . 3

Foreword
This document (EN ISO 14910-1:2013) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14910-1:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14910-1:2013 has been approved by CEN as EN ISO 14910-1:2013 without any modification.

INTERNATIONAL ISO
STANDARD 14910-1
Second edition
2013-03-01
Plastics — Thermoplastic polyester/
ester and polyether/ester elastomers
for moulding and extrusion —
Part 1:
Designation system and basis for
specification
Plastiques — Élastomères thermoplastiques à base de polyester/ester
et polyéther/ester, pour moulage et extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 14910-1:2013(E)
©
ISO 2013
ISO 14910-1:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 14910-1:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Designation system . 2
3.1 General . 2
3.2 Data block 1 . 2
3.3 Data block 2 . 3
3.4 Data block 3 . 4
3.5 Data block 4 . 5
3.6 Data block 5 . 6
4 Examples of designations . 6
Annex A (informative) Definition of thermoplastic polyester/ester and polyether/
estercopolymer elastomers . 8
ISO 14910-1:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14910-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This second edition cancels and replaces the first edition (ISO 14910-1:1997), which has been
technically revised.
ISO 14910 consists of the following parts, under the general title Plastics — Thermoplastic polyester/ester
and polyether/ester elastomers for moulding and extrusion:
— Part 1: Designation system and basis for specification
— Part 2: Preparation of test specimens and determination of properties
iv © ISO 2013 – All rights reserved

INTERNATIONAL STANDARD ISO 14910-1:2013(E)
Plastics — Thermoplastic polyester/ester and polyether/
ester elastomers for moulding and extrusion —
Part 1:
Designation system and basis for specification
1 Scope
This part of ISO 14910 establishes a system of designation for thermoplastic polyester/ester and
polyether/ester elastomers, which may be used as the basis for specifications.
The types of thermoplastic polyester/ester and polyether/ester elastomer are differentiated from each
other by a classification system based on appropriate levels of the designatory properties
a) hardness;
b) melting temperature;
c) tensile/flexural modulus of elasticity;
and on information about the intended application and/or method of processing, important properties,
additives, colour, fillers and reinforcing materials.
This part of ISO 14910 is applicable to all thermoplastic polyester/ester and polyether/ester elastomers.
It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or
modified by colourants, fillers or other additives.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This part of ISO 14910 does not provide engineering data, performance data or data on
processing conditions which might be required to specify a material for a particular application and/or
method of processing. If such additional properties are required, they shall be determined in accordance
with the test methods specified in ISO 14910-2, if suitable.
In order to specify a thermoplastic polyester/ester or polyether/ester elastomer for a particular
application or to ensure reproducible processing, additional requirements may be given in data block 5
(see 3.1 and 3.6).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 14910-2, Plastics — Thermoplastic polyester/ester and polyether/ester elastomers for moulding and
extrusion — Part 2: Preparation of test specimens and determination of properties
ISO 18064, Thermoplastic elastomers — Nomenclature and abbreviated terms
ISO 14910-1:2013(E)
3 Designation system
3.1 General
The designation system for thermoplastics is based on the following standardized pattern.
Designation
Identity block
Description International Individual-item block
block Standard
Data block 1 Data block 2 Data block 3 Data block 4 Data block 5
(optional) number
block
The designation consists of an optional description block, reading “Thermoplastics”, and an identity block
comprising the International Standard number and an individual-item block. For unambiguous designation,
the individual-item block is subdivided into five data blocks comprising the following information:
— Data block 1: Identification of the plastic by its abbreviated term (TPC), in accordance with
ISO 18064, and information on the alternating hard and soft segments in the main
chain (see 3.2).
— Data block 2: Position 1: Intended application and/or method of processing (see 3.3).
Positions 2 to 8: Important properties, additives and supplementary information
(see 3.3).
— Data block 3: Designatory properties (see 3.4).
— Data block 4: Fillers or reinforcing materials and their nominal content (see 3.5).
— Data block 5: For the purpose o
...